IEX-402-SHDSL Series Hardware Installation Guide Moxa Managed SHDSL Ethernet Extender First Edition, October 2012 2012 Moxa Inc. All rights reserved.
Overview The Moxa IEX-402-SHDSL Series Ethernet Extender consists of one 10/100BaseT(x) port and a DSL interface that provides an economical solution for your Ethernet connections. Utilizing SHDSL technology over copper wires, the IEX-402-SHDSL series supports data rates of up to 15.3 Mbps and long transmission distance of over 8 km. Advanced managed functionality provides highly reliable communication for networks.
IEX-402-SHDSL Panel Layout Front Panel View Top Panel View 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19.
Mounting Dimensions (unit = mm[inches]) -4-
DIN-Rail Mounting The aluminum DIN-Rail attachment plate should already be fixed to the back panel of the IEX-402-SHDSL when you take it out of the box. If you need to reattach the DIN-Rail attachment plate, make sure the stiff metal spring is situated towards the top, as shown in the following figures. STEP 1: Insert the top of the DIN-Rail into the slot just below the stiff metal spring. STEP 2: The DIN-Rail attachment unit will snap into place as shown below.
NOTE Before tightening the screws into the wall, make sure the screw head and shank size are suitable by inserting the screw into one of the keyhole-shaped apertures of the wall mounting plates. Do not screw the screws in completely—leave about 2 mm to allow room for sliding the wall mount panel between the wall and the screws.
Wiring the Redundant Power Inputs Both power inputs can be connected simultaneously to live DC power sources. If one power source fails, the other live source acts as a backup, and automatically supplies the IEX-402-SHDSL with power. The two 2-contact terminal block connectors on the IEX's top panel are used for IEX's two DC power inputs. Top and front view of the terminal block connectors are shown here.
RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring DSL Port Connection The DSL port located on the IEX-402-SHDSL has two connection options. One is the RJ45 connector interface (2-wire on pin 4 and pin 5), the other is the screw detachable interface. Pinouts are illustrated below.
RS-232 Console Port Connection The IEX-402-SHDSL has one RS-232 (10-pin RJ45) console port, located on the top panel. Use either an RJ45-to-DB9 (see the cable following wiring diagrams) to connect the IEX-402-SHDSL‘s console port to your PC’s COM port. You may then use console terminal software, such as Moxa PComm Terminal Emulator, to access the IEX-402-SHDSL’S serial console.
Restore Factory Defaults Button Press and hold the Reset button for 5 seconds to load the factory default settings. Use a pointed object, such as a straightened paper clip or toothpick, to depress the Reset button. This will cause the STATE LED to blink once a second. After depressing the button for 5 continuous seconds, the STATE LED will start to blink rapidly. This indicates that factory default settings have been loaded and you can release the reset button.
rate follows defined standard mode value defined Turbo mode value LED Indicators LED Color PWR1 AMBER State On Off On PWR2 AMBER Off On GREEN Blinking STATE On RED Blinking FAULT RED On Off On 10/100M (TP port) GREEN Blinking Off On GREEN Blinking Off LINK/ACT On AMBER GREEN CO/CPE AMBER Blinking Off On Off On Off Description Power is being supplied to the power input PWR1 Power is not being supplied to the power input PWR1 Power is being supplied to the power input PWR2 Power is not
DSL Speed/SNR LED Indicator Five Levels of SNR/SPEED Setting 5 4 3 2 1 Turbo Speed (K bits) 10297 – 15304 5697 – 10296 3457 – 5696 1025 – 3456 192 – 1024 5 4 3 2 1 STD Speed (K bits) 4609 – 5760 3073 – 4608 2049 – 3072 769 – 2048 192 – 768 5 4 3 2 1 SNR (dB) 18 – 30 14 – 17 10 – 13 6–9 3–5 Specifications Technology Standards SHDSL Data Rate Protocols MIB Flow Control Interface RJ45 Port DSL Port Console LED Indicators DIP Switches Power Input Voltage Input Current (@24V) Connection Overload Current P
Reverse Polarity Present Protection Physical Characteristics Housing Metal, IP30 protected Dimension 35 x 130 x 105 mm Weight 0.
