OPERATION AND PARTS MANUAL MODEL QP2H CENTRIFUGAL PUMP (HONDA GX120U1PX2 GASOLINE ENGINE) Revision #0 (08/04/08) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PROPOSITION 65 WARNING PAGE 2 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
NOTES QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
TABLE OF CONTENTS QP2H Centrifugal Pump Honda GX120U1PX2 Engine Proposition 65 Warning ........................................... 2 Table of Contents .................................................... 4 Parts Ordering Procedures ..................................... 5 Safety Information ................................................ 6-9 Specifications/Dimensions (Pump) ....................... 10 Specifications/Dimensions (Engine) ..................... 11 General Information .........................
www.multiquip.com PARTS ORDERING PROCEDURES Ordering parts has never been easier! Choose from three easy options: Effective: January 1st, 2006 Best Deal! Order via Internet (Dealers Only): If you have an MQ Account, to obtain a Username and Password, E-mail us at: parts@multiquip.com. Order parts on-line using Multiquip’s SmartEquip website! ■ View Parts Diagrams ■ Order Parts ■ Print Specification Information To obtain an MQ Account, contact your District Sales Manager for more information.
SAFETY INFORMATION FOR YOUR SAFETY AND SAFETY OF OTHERS! HAZARD SYMBOLS Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the safety messages and operating instructions could result in injury to yourself and others. Potential hazards associated with the operation of this equipment will be referenced with hazard symbols which may appear throughout this manual in conjunction with safety messages.
SAFETY INFORMATION GENERAL SAFETY ■ DO NOT operate or service this equipment before reading the entire manual. The equipment is to be operated by trained and qualified personnel only! The equipment is for industrial use only. ■ This equipment should not be operated by persons under 18 years of age. ■ NEVER operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job.
SAFETY INFORMATION ■ NEVER run engine without air cleaner. Severe engine damage may occur. ■ ALWAYS ensure pump is on level ground before use. ■ NEVER pump volatile, explosive, flammable or low flash point fluids. These fluids could ignite or explode. NEVER pump corrosive chemicals or water containing toxic substances. These fluids could create serious health and environmental hazards. Contact local authorities for assistance. ■ NEVER open the priming plug when pump is hot.
SAFETY INFORMATION REFUELING EMERGENCIES ■ ALWAYS know the location of the nearest fire extinguisher. ■ ALWAYS know the location of the nearest first aid kit. ■ In emergencies, always know the location of the nearest phone or keep a phone on the job site. Also know the phone numbers of the nearest ambulance , doctor and fire department . This information will be invaluable in case of emergency. MAINTENANCE SAFETY ■ NEVER lubricate components or attempt service on a running machine.
SPECIFICATIONS/DIMENSIONS (PUMP) Table 1. Specifications (Pump) Pump Model MQ QP2H Type Centrifugal Pump Suction & Discharge Size 2.00 in. (51 mm.) Maximum Pumping Capacity 158 gallons/minute (600 liters/minute) Max. Lift 25 ft. (7.62 meters) Max. Head 115 ft. (35.0 meters) 53 lbs. (24 Kg.) Dry Net Weight Figure 1. QP2H Dimensions PAGE 10 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
SPECIFICATIONS/DIMENSIONS (ENGINE) Table 2. Specifications (Engine) Model HONDA GX120U1PX2 Type Air-cooled 4 stroke, Single Cylinder, OHV, Horizontal Shaft Gasoline Engine Bore X Stroke 2.4 in. x 1.6 in. (60 mm x 42 mm) Displacement 118 cc (7.3 cu-in) Max Output 4.0 H.P./3600 R.P.M. Engine Fuel Tank Capacity Fuel Lube Oil Capacity Approx. 0.66 U.S. gallons (2.5 liters) Unleaded Automobile Gasoline .60 liters (0.
GENERAL INFORMATION APPLICATION The QP2H Centrifugal Pump is designed to handle all types of clear water applications. It is ideal for residential use such as dewatering basements and swimming pools. Both the suction and discharge ports on the QP2H pump use a 2-inch diameter opening, which allows the pump to pump at a rate of approximately 158 gallons/minute (gpm) or 600 liters/minute (lpm).
PUMP COMPONENTS Figure 2 shows a typical application using the QP2H centrifugal pump. Please note that this pump is intended for the removal of clean water. Figure 2. QP2H Pump Application 1. Pump – The QP2H is 2-inch centrifugal pump used in general de-watering applications. Typical dewatering applications consist of dewatering basements and swimming pools. 2. Fill Cap – Prior to operation, the pump casing should be filled with water. Remove this cap to add water to the pump.
BASIC ENGINE INITIAL SERVICING The engine (Figure 4) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturers engine manual for instructions and details of operation and servicing. The engine shown above is a HONDA engine, operation for other types of engines may vary somewhat. 1. Fuel Filler Cap – Remove this cap to add unleaded gasoline to the fuel tank. Make sure cap is tightened securely. DO NOT over fill.
NOTES QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
INSPECTION (ENGINE) CAUTION — Read Manual DO NOT attempt to operate the pump until the Safety Information, General Information and Inspection sections of this manual have been read and thoroughly understood. 3. Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick. 4. If the oil level is low (Figure 6), fill to the edge of the oil filler hole with the recommended oil type (Table 5). Maximum oil capacity is 0.63 quarts (0.60 liters).
SET-UP SET-UP 1. Place pump as near to water as possible, on a firm flat, level surface. 2. To prime pump, remove fill cap (Figure 2) and fill pump casing with water. If the pump casing is not filled with water before starting, it will not begin pumping. 3. Attach suction and discharge hoses to the pump. Check that all hoses are securely attached to the pump. Make certain suction hose (Figure 2) does not have any air leakage. Tighten hose clamps and couplings as required. 4.
OPERATION STARTING THE ENGINE 4. Place the choke lever (Figure 10) in the OPEN position if starting a warm engine or the temperature is warm. CAUTION — Pump Priming DO NOT attempt to start the engine unless the pump has previously been primed with water. Severe pump damage will occur if pump has not been primed. 1. Place the engine fuel valve lever (Figure 7) to the ON position. Figure 10. Engine Choke Lever (Open) 5. Place the engine ON/OFF switch (Figure 11) in the ON position. Figure 7.
OPERATION CAUTION — Maximum Engine Speed ALWAYS run engine at full speed while pumping. STOPPING THE ENGINE Normal Shutdown 1. Move the throttle lever to the IDLE position (Figure 15) and run the engine for three minutes at low speed. Figure 13. Choke Lever (Open) 8. Before the pump is placed into operation, run the engine for several minutes. 9. Check for fuel leaks and noises that would be associated with a loose component.Check for leaks between pump and engine.
MAINTENANCE (PUMP) PUMP VACUUM TEST CAUTION — Pump Priming DO NOT attempt to start the engine unless the pump has previously been primed with water. Severe pump damage will occur if pump has not been primed. To perform the pump vacuum test do the following: 1. Remove the pump fill cap (Figure 2), and fill the pump with water. 7. If the vacuum tester gauge indicates a reading below -20 in. Hg, it can then be assumed that the pump is not functioning correctly, and corrective action needs to be taken. 8.
MAINTENANCE (PUMP) Figure 18. Pump Vacuum Tester Vacuum test may be performed without water flowing through the discharge port. However, it is recommended to have water flowing to prevent any heat-up. QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
MAINTENANCE (ENGINE) ENGINE MAINTENANCE Perform engine maintenance procedures as referenced by Table 6 below: Table 6. Engine Maintenance Schedule DESCRIPTION (3) OPERATION BEFORE CHECK X FIRST EVERY FIRST MONTH 3 MONTHS 25 OR OR HRS. 10 HRS. 25 HRS. EVERY 6 MONTHS OR 50 HRS. EVERY EVERY YEAR YEAR OR OR 100 HRS. 200 HRS. EVERY 2 YEARS OR 200 HRS.
MAINTENANCE (ENGINE) MAINTENANCE Perform the engine maintenance procedures as indicated below: DAILY ■ Thoroughly remove dirt and oil from the engine and control area. Clean or replace the air cleaner elements as necessary. Check and retighten all fasteners as necessary. Check the spring box and bellows for oil leaks. Repair or replace as needed. WEEKLY ■ Remove the fuel filter cap and clean the inside of the fuel tank. ■ Remove or clean the filter at the bottom of the tank.
STORAGE PUMP STORAGE For storage of the pump for over 30 days, the following is required: ■ Drain the fuel tank completely. ■ Run the engine until the fuel in the carburetor is completely consumed. ■ Completely drain used oil from the engine crankcase and fill with fresh clean oil, then follow the procedures described in the engine manual for engine storage. ■ Remove the drain plug from the pump and drain out any water from left in the housing. ■ Remove the pump cover and clean inside of pump housing.
TROUBLESHOOTING (ENGINE) TABLE 7. ENGINE TROUBLESHOOTING SYMPTOM POSSIBLE PROBLEM SOLUTION Difficult to start Fuel is available but spark plug will not ignite. (Power available at high tension cable). Fuel is available but spark plug will not ignite. (Power NOT available at high tension cable). Fuel is available and spark plug ignites (compression normal). Fuel is available and spark plug ignites (compression low ). Ignition plug being bridge? Check ignition system.
TROUBLESHOOTING (ENGINE/PUMP) TABLE 7. ENGINE TROUBLESHOOTING (Continued) SYMPTOM POSSIBLE PROBLEM SOLUTION Operation not satisfactory Rotational speed fluctuates. Recoil star ter not working properly. Governor adjustment improper? Adjust governor to correct lever. Governor spring defective? Clean or replace ignition. Fuel flow erratic? Check fuel line. Air taken in through suction line? Check suction line. Dust in rotating par t? Clean recoil star ter assembly.
NOTES QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions. The contents and part numbers listed in the parts section are subject to change without notice. Multiquip does not guarantee the availibility of the parts listed. * * Numbers Used - Item quantity can be indicated by a number, a blank entry, or A/R.
SUGGESTED SPARE PARTS QP2H CENTRIFUGAL PUMP 1 TO 3 UNITS WITH HONDA GX120U1PX2 ENG. Qty. 2 2 2 1 2 3 3 1 P/N Description KIT204 ................ KIT, PUMP 0631211100 ........ DRAIN CAP, FLOODING 0480350300 ........ O-RING DRAIN CAP 9258000030 ........ IMPELLER 17210ZE0822 ..... ELEMENT AIR CLEANER DUAL 9807955855 ........ SPARK PLUG 28461ZH8003 ..... ROPE STARTER 17620Z0T305 ......
PUMP ASSY. PAGE 30 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
PUMP ASSY. NO. 1 2 3 4 5 6 7% 8% 9% 10% 10% 11 12 13 14 15 16 PART NO.
HONDA GX120U1PX2 ENGINE — AIR CLEANER (DUAL) ASSY. PAGE 32 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — AIR CLEANER (DUAL) ASSY. NO. 1 2 3% 4 5% 7+ 8+ 9 12 13 14 PART NO. 16271ZE1000 17210ZE0822 17218ZE0821 17230ZE0820 17323891000 17238ZE0010 17239ZE1000 17410ZE0030 90325044000 957010602000 9405006000 PART NAME QTY. REMARKS GASKET, ELBOW 1 ELEMENT, AIR CLEANER (DUAL) ............. 1 ............... INCLUDES ITEMS W/% FILTER, OUTER 1 COVER, AIR CLEANER (DUAL) 1 GROMMET, AIR CLEANER 1 COLLAR, AIR CLEANER 2 COLLAR B, AIR CLEANER 1 ELBOW, AIR CLEANER .............................. 1 ..
HONDA GX120U1PX2 ENGINE — CAMSHAFT ASSY. PAGE 34 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — CAMSHAFT ASSY. NO. 1 2 3 4 5 6# 7 8 9 10 11 12 13 14 15 PART NO. 14100ZE0812 14410ZE0010 14431ZE1000 14441ZE1010 14451ZE1013 14568ZE1000 14711ZF0010 14721ZH7810 14751ZF1000 14771ZE1000 14773ZE1000 14781ZE1000 14791ZE0010 90012ZE0010 90206ZE1000 PART NAME QTY. REMARKS CAMSHAFT ASSEMBLY ......................... 1.................. INCLUDES ITEMS W/# ROD, PUSH 2 ARM, VALVE ROCKER 2 LIFTER, VALVE 2 PIVOT, ROCKER ARM 2 SPRING, WEIGHT RETURN 1 VALVE, IN. 1 VALVE, EX.
HONDA GX120U1PX2 ENGINE — CARBURETOR ASSY. PAGE 36 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — CARBURETOR ASSY. NO. 1% 2% 3% 4% 5% 6% 7% 8% 9 10% 11% 12% 13 14 15 16 17 18% 19% 19% 20% 21% 22% 23% 24%+ 25 25 25% 26% PART NO.
HONDA GX120U1PX2 ENGINE — CONTROL ASSY. PAGE 38 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — CONTROL ASSY. NO. 1 4 5 6 7 8# 9# 10# 12# 13# 14# 15# 18 19 20 21# 24# 26 PART NO. 16500ZH7000 16551ZE0010 16555ZE0000 16561ZE0020 16562ZE0020 16571ZH7000 16574ZE1000 16575ZH8000 16578ZE1000 16580ZH7000 16575ZH8000 16584883300 90013883000 90015ZE5010 90022888010 90114SA0000 93500050250H 9405006000 PART NAME QTY. REMARKS CONTROL ASSEMBLY ............................ 1..................
HONDA GX120U1PX2 ENGINE — CRANKCASE COVER ASSY. PAGE 40 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — CRANKCASE COVER ASSY. NO. 1 2 3 4 7+# 9 10% 11% 12 PART NO. 11300ZE0641 11381ZH7800 15600ZE1003 15600ZG4003 15625ZE1003 90015883000 91001878003 91203ZE0013 9430108140 PART NAME QTY. REMARKS COVER ASSY., CRANKCASE(U- TYPE) ........ 1........... INCLUDES ITEMS W/% GASKET, CASE COVER 1 CAP ASSEMBLY, OIL FILLER ........................ 1........... INCLUDES ITEM W/+ CAP ASSEMBLY, OIL FILLER ........................ 1...........
HONDA GX120U1PX2 ENGINE — CRANKSHAFT ASSY. PAGE 42 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — CRANKSHAFT ASSY. NO. 6 PART NO. 13310ZE0650 PART NAME CRANKSHAFT, P-TYPE QTY. 1 REMARKS QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — CYLINDER BARREL ASSY. PAGE 44 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — CYLINDER BARREL ASSY. NO. 2 3 4 5% 6% 7% 8 9 12 13 14 15 16# 17# 18 19 20 21 20 PART NO. 12000ZH7425 15510ZE1033 16510ZE1000 16511ZE1000 16512ZE1000 16513ZE1000 16531ZE1000 16541ZE1000 90131ZE1000 90451ZE1000 90601ZE1000 90602ZE1000? 91001878003 91202ZE6013 91353671003 9405010000 9410106800 9425108000 957010601200 PART NAME QTY. REMARKS CYLINDER BARREL ASSEMBLY ............ 1.................. INCLUDES ITEMS W/# SWITCH ASSEMBLY, OIL LEVEL 1 GOVERNOR ASSEMBLLY ....................
HONDA GX120U1PX2 ENGINE — CYLINDER HEAD ASSY. PAGE 46 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — CYLINDER HEAD ASSY. NO. 1 2 3 4+ 5 6 7 8 9 10 11 12 14 15 15 15 15 PART NO. 12210ZH7405 12204ZE1306 12205ZE1315 12216ZE5300 12251ZH7800 12310ZE1020 12391ZE1000 15721ZH8000 90013883000 90043ZE1020 90047ZE1000 9430110160 957230805500 9807955846 9807956846 9807955855 9807956855 PART NAME QTY. REMARKS CYLINDER HEAD ............................................1 .......... INCLUDES ITEMS W/# GUIDE, VALVE (OS) OPTIONAL 1 GUIDE, EX. VALVE (OS) OPTIONAL .............1 ..........
HONDA GX120U1PX2 ENGINE — FAN COVER ASSY. PAGE 48 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — FAN COVER ASSY. NO. 1 2 3 4 5 7 8 9 10 11 13 PART NO. 1134371300 19610ZE0000ZE 19611ZH7810 90601ZH7013 19630ZH7000 36100ZF6P81 36101ZE1010 90013883000 90022888010 34150ZH7003 957010600800 PART NAME QTY. REMARKS GROMET, ADJUSTING CABLE 1 COVER, FAN *NH1* BLACK 1 PLATE, SIDE(OIL ALERT) 1 CLIP, HARNESS 1 SHROUD 1 SWITCH ASSEMBLY, ENGINE STOP 1 WIRE, STOP SWITCH 370MM 1 BOLT, FLANG 6 X 12 (CT200) 6 BOLT, FLANG 6 X 12 (CT200) 1 ALERT UNIT, OIL .......................................
HONDA GX120U1PX2 ENGINE — FLYWHEEL ASSY. PAGE 50 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — FLYWHEEL ASSY. NO. 1 2 4 5 7 PART NO. 13331357000 19511ZE0000 28451ZH7801 31100ZE0010 90201878003 PART NAME KEY, SPECIAL WOODRUFF 25X18 FAN, COOLING PULLEY, STARTER FLYWHEEL NUT, SPECIAL 14MM QTY. 1 1 1 1 1 REMARKS QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — FUEL TANK ASSY. PAGE 52 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — FUEL TANK ASSY. NO. 1 2 3 5 6% 11 12 13 14 15 PART NO. 16854ZH8000 16955ZE1000 17510ZE0020ZD 17620Z0T305 17631Z0T812 91353671004 9405006000 950014514040 9500202080 90004ZH7003 PART NAME QTY. REMARKS RUBBER, SUPPORTER 107MM 1 JOINT, FUEL TANK 1 TANK, FUEL *NH1* (BLACK) 1 CAP COMP., FUEL FILLER (CHROME) ..........1 .......... INCLUDES ITEMS W/% GASKET, FUEL FILLER CAP 1 O- RING 14MM (NOK) 1 NUT, FLANGE 6MM 2 BULK HOSE, FUEL (4.5X3000) (4.
HONDA GX120U1PX2 ENGINE — IGNITION COIL ASSY. PAGE 54 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — IGNITION COIL ASSY. NO. 1 2 8 PART NO. 30500ZE1063 30700ZE1013 90121952000 PART NAME COIL ASSEMBLY, IGNITION CAP ASSEMBLY, NOISE SUPPRESSOR BOLT, FLANGE 6X25 QTY. 1 1 2 REMARKS QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — MUFFLER ASSY. PAGE 56 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — MUFFLER ASSY. NO. 1 3 7 10 13 PART NO. 18310ZF1000 18320ZF1H01 18381ZH8800 90050ZE1000 94001080000S PART NAME MUFFLER (STD) PROTECTOR, MUFFLER (STD BLACK) GASKET, MUFFLER SCREW, TAPPING 5X8 NUT, HEX. 8MM QTY. 1 1 1 4 2 REMARKS QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — PISTON ASSY. PAGE 58 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — PISTON ASSY. NO. 1 1 1 1 1 1 1 1 2 2 2 2 3 4 5# 6 PART NO. 13010ZE6013 13010ZK7V01 13011ZE6013 13011ZK7V01 13012ZE6013 13012ZK7V01 13013ZE6013 13013ZK7V01 13101ZH7000 13102ZH7000 13103ZH7000 13104ZH7000 13111ZE0000 13200ZE0000 90001ZE1000 90551ZE0000 PART NAME QTY. REMARKS RING SET, PISTON (STANDARD) 1 RING SET, PISTON (STANDARD) 1 RING SET, PISTON ( 0.25) 1 RING SET, PISTON ( 0.25) 1 RING SET, PISTON ( 0.50) 1 RING SET, PISTON ( 0.50) 1 RING SET, PISTON (0.
HONDA GX120U1PX2 ENGINE — RECOIL STARTER ASSY. PAGE 60 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — RECOIL STARTER ASSY. NO. 1 2# 3# 4# 5# 6# 7# 8# 9# 10# 11# 12 PART NO. 28400ZH8023ZB 28410ZH8003ZB 28421ZH8801 28422ZH8801 28431ZH8801 28433ZH8801 28441ZH8801 28442ZH8003 28443ZH8801 28461ZH8003 28462ZH8003 90008ZE2003 PART NAME QTY. REMARKS STARTER ASSY., RECOIL *NH1* (BLACK) ......... 1 .............
HONDA GX120U1PX2 ENGINE — GASKET ASSY. PAGE 62 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — GASKET ASSY. NO. 1# 2# 3# 4# 5# 6# 7 PART NO. 11381ZH7800 12251ZH7800 12391ZE1000 16212ZH7800 16221ZH8801 18381ZH8800 06111ZH7405 PART NAME QTY. REMARKS GASKET, CASE COVER 1 GASKET, CYLINDER HEAD 1 GASKET, CYLINDER HEAD COVER 1 GASKET, INSULATOR 1 GASKET, CARBURETOR 1 GASKET, MUFFLER 1 GASKET KIT ............................................... 1 ............. INCLUDES ITEM W/# QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — LABELS ASSY. PAGE 64 — QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
HONDA GX120U1PX2 ENGINE — LABELS ASSY. NO. 1 2 3 4 5 PART NO. 87521ZH7030 87516ZH7000 87522ZH9000 87528ZH7000 87532ZH7000 PART NAME EMBLEM MARK OPERATOR CAUTION (ENGLISH) LABEL, CAUTION MARK, CHOKE (GRAY) MARK, THROTTLE INDICATION QTY. 1 1 1 1 1 REMARKS QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
TERMS AND CONDITIONS OF SALE — PARTS PAYMENT TERMS 5. Parts must be in new and resalable condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked. 6. The following items are not returnable: Terms of payment for parts are net 30 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin.
NOTES QP2H CENTRIFUGAL PUMP • OPERATION AND PARTS MANUAL — REV.
OPERATION AND PARTS MANUAL HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES Multiquip Corporate Office 18910 Wilmington Ave. Tel. (800) 421-1244 Carson, CA 90746 Fax (800) 537-3927 Contact: mq@multiquip.