MultiModem® rCell Intelligent Wireless Router User Guide
MultiModem® rCell User Guide Intelligent Wireless Router MTCBA-Xx-EN3 S000508D, Revision D Copyright This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. All rights reserved. Copyright © 2013 by Multi-Tech Systems, Inc. Multi-Tech Systems, Inc. makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.
Contents Chapter 1 – Introduction and Description.......................................................................................................... 6 Introduction ........................................................................................................................................................... 6 Package Contents ...................................................................................................................................................
Contents Screen Buttons............................................................................................................................................... 23 Submenus ...................................................................................................................................................... 24 Web Management Software Screens................................................................................................................... 24 IP Setup ...................
Contents Tools > Load Configuration ............................................................................................................................ 55 Tools > Save Configuration ............................................................................................................................ 55 Statistics & Logs....................................................................................................................................................
Chapter 1 – Introduction and Description Introduction This guide describes the MultiModem® rCell intelligent wireless routers with an Ethernet II interface. The MultiModem rCell Router is configured for one of three connectivity modes: always-on, wake-up on ring, or dialon demand. The always-on network connection automatically establishes a wireless data connection and allows for around the clock surveillance, monitoring or real time data acquisition of any remote Ethernet device such as a Web camera.
Chapter 1 – Introduction and Description Safety Warnings Ethernet Ports CAUTION: The Ethernet ports and command ports are not designed to be connected to a public telecommunication network. ATTENTION: Ports Ethernet et des ports de commande ne sont pas conçus pour être connecté à un réseau de télécommunication public. RF Safety Due to the possibility of radio frequency (RF) interference, it is important that you follow any special regulations regarding the use of radio equipment.
Chapter 1 – Introduction and Description ● Éteignez votre appareil sans fil dans un avion. Utilisant des dispositifs électroniques portables dans un avion peut mettre en danger le fonctionnement de l'avion, peut perturber le réseau cellulaire, et est illégal. Le nonrespect de cette restriction peut entraîner la suspension ou le refus des services cellulaires au contrevenant, une action en justice, ou les deux.
Chapter 1 – Introduction and Description ● Keep the device on the opposite the side of the body from the pacemaker to add extra distance between the pacemaker and the device. ● Avoid placing a turned-on device next to the pacemaker (for example, don’t carry the device in a shirt or jacket pocket directly over the pacemaker). Front Panel The front panel contains nine LEDs and the SIM card holder. For details on inserting a SIM card, refer to Insert the SIM Card into Holder.
Chapter 1 – Introduction and Description Specifications General Standards Frequency Bands Speed Packet Data* Circuit Swithed Data Physical Description Dimensions Weight (Device Only) Connectors Antenna Connector SIM Holder LAN Connector HSPA Quad-band: 850/900/1900/2100 MHz HSDPA data service of up to 7.2 Mbps HSUPA data service of up to 5.76 Mbps Up to 14.4K bps, non-transparent 3.34 in x 6.05 in x 1.51 in 8.48 cm x 16.51 cm x 3.84 cm 0.72 lbs 0.
Chapter 1 – Introduction and Description Certifications and Compliance EMC Compliance FCC Part 15 Class B EN55022 Class B EN55024 Radio Compliance FCC Part 22, 24 RSS102,132, 133 EN301 489-1 EN489-3 (GPS models only) EN301 489-7 EN301 489-24 EN301 511 Safety Certifications UL/cUL 60950-1 2nd Ed IEC60950-1 2nd Ed am.1 Network Certifications PTCRB AT&T 1UL Listed at 40° C, limited by power supply.
Chapter 1 – Introduction and Description Power Draw Multi-Tech Systems, Inc. recommends that you incorporate a 10% buffer into your power source when determining product load. Input Voltage= 5.0Volts Idle Mode Typical Maximum Peak Tx Peak Rst (Inrush Current) GSM850 Current(AMPS) Watts HSDPA 0.345 1.76 0.450 2.29 1.20 5.94 3.60 Current(AMPS) 0.345 0.760 1.01 1.40 Watts 1.76 3.84 5.03 Inrush Current (AMPS) (approx. 3ms duration) 2.
Chapter 1 – Introduction and Description GSM Antenna Requirements/Specifications Frequency Range Impedance VSWR Typical Radiated Gain Radiation Polarization TRP/TIS 13 824 – 960 MHz / 1710 – 1990 MHz 50 Ohms VSWR shall not exceed 2.0:1 at any point across the bands of operation 3 dBi on azimuth plane Omni-directional Vertical Including cable loss the total radiated power (TRP) at the antenna shall be no less than +22/24.
Chapter 2 - Installation Inserting the SIM The router requires the power supply connection to begin operation. It also requires a SIM card (Subscriber Identity Module) to operate on a GSM network. To install the SIM, do the following: 1. Open the SIM door by pressing down on the tab on the top of the door and prying it open. Note: When changing a SIM, disconnect power. 2. Insert the SIM card into the card holder. The image above shows the correct SIM card orientation. 3.
Chapter 2 – Installation Mounting the Router Before you mount your router to a permanent surface, verify signal strength, refer to Verify Signal Strength in this Chapter. The router can be panel mounted with screws spaced according to the measurement shown. Note: Use either #6 or #8 pan head screws for all four mounts. Setting the TCP/IP Address Establish a TCP/IP connection at the pc so the PC can communicate with the router. Note that these steps are based on Windows XP. 1.
Chapter 2 – Installation The Local Area Connection Properties dialog box displays. 3. Select Internet Protocol [TCP/IP] and click Properties. The Internet Protocol (TCP/IP) Properties screen displays. Note: If the Internet Protocol (TCP/IP) Properties shows your current IP configuration, record this information. You may want to restore the computer’s settings after configuring the router. 4. Enter TCP/IP Properties for a Fixed IP Address. Repeat these steps for each computer on your network a.
Chapter 2 – Installation Note: The computer’s settings must be in the same subnet range as the router. The factory default settings for the router are: IP Address: 192.168.2.1 Subnet Mask: 255.255.255.0 e. Select Use the following DNS server addresses. f. Enter the IP Address for the Preferred DNS Server and click OK. Example: 205.171.3.65 g. Close the Local Area Properties screen by clicking OK.
Chapter 2 – Installation The Wizard Setup screen displays. Wizard Setup A minimum router configuration is provided using the Wizard Setup. This provides a quick way to enter and save information needed to create a connection to the Internet. The table below provides the information for the minimum configuration. IP Configuration IP Address The default is 192.168.2.1. To change it, simply enter your own IP address. Mask The default is 255.255.255.0 DNS Enter the primary DNS IP address for the system.
Chapter 2 – Installation PPP Authentication Authenticatio Click the button corresponding to the authentication protocol you want to use n to negotiate with the remote peer. PAP, CHAP, or PAP-CHAP. T Default = PAP-CHAP y p e Username Enter the PPP Username. This name authenticates the remote peer. Password Enter the PPP Password. This password authenticates the remote peer. 1. Enter settings. 2. Click Submit. 3. Click Save & Restart to reboot.
Chapter 2 – Installation In the command window, type telnet 192.168.2.1 5000 At the Login prompt, type the default user name: admin (all lower-case). Press ENTER At the Password prompt, type the default password: admin (all lower-case). Press ENTER 2. In the command window, type AT+CSQ . The router responds with the received signal strength (rssi).
Chapter 3 - Web Management Software Use the Web Management software to configures your router’s Ethernet functions. Navigating the Web Management Software This section explains the menu structure and the navigation buttons of the router’s Web Management software. Menu Bar IP Setup: Sets up a General Configuration, HTTP, DDNS, SNTP, Static Routes, and Remote Configuration. PPP: Sets up the PPP authentication, dial-on-demand, router authentication, and Wakeup on Call.
Chapter 3 – Using the Web Management Software Screen Parts Menu Bar Submenu Title Submenu List Screen Buttons Screen Name Screen Input Area Screen Buttons Home: Click this button to return to the Home screen. Wizard Setup: Click this button to display the Wizard Setup screen on which you can quickly set up your MultiModem rCell Router with basic configuration settings. Logout: Click this button to Logout and return to the login screen. Help: Click this button to display the Help text.
Chapter 3 – Using the Web Management Software Submenus The submenus display on the left side of the screen. The following table shows the sub-menu selections under each main menu category.
Chapter 3 – Using the Web Management Software IP Setup Setup > General Configuration In the General Configuration, you will set the general system-based parameters. 25 Multi-Tech Systems, Inc.
Chapter 3 – Using the Web Management Software General Configuration Date and Time: The system date and time display in these formats: MM/DD/YYYY / HH:MM:SS. A real time clock is part of SNTP to display proper time. IP Configuration Enter the following addresses for the Ethernet interface. IP Address: Default = 192.168.2.1 Mask: Default 255.255.255.0 Default Gateway: Default 0.0.0.0 Primary DNS: Default 0.0.0.0 Secondary DNS: Default 0.0.0.
Chapter 3 – Using the Web Management Software Server Port: Enter the Server Port Number. Default port is 1020. Broadcast Timer: Enter the amount of time in seconds for the auto-discovery packet granularity of periodic broadcasting. Default is 10 seconds. Auto Reboot Timer Configuration Auto Reboot Timer: Enter the number of hours to lapse between each automatic reboot. The default of zero deactivates the timer. Range is 0 to 999. Telnet Configuration Enables/Disables the Telnet port.
Chapter 3 – Using the Web Management Software IP Setup > DDNS Configuration DDNS (Dynamic Domain Naming System) is dependent upon cellular network/account configuration. DDNS allows you to have a static domain name with a dynamic IP address. Whenever your dynamic IP address changes, it is submitted to the DDNS server where your domain name is updated to point to the new IP address. Note: You have to register with a DDNS server to use this feature. General DDNS: Check the Enable or Disable box.
Chapter 3 – Using the Web Management Software Domain: Enter the registered Domain name. Authentication Username: Enter the Username that can access the DDNS Server. Default = NULL. You should have received your username when you registered with the DDNS service. Password: Enter the Password that can access the DDNS Server. Default = NULL. You should have received your password when you registered with the DDNS service.
Chapter 3 – Using the Web Management Software Time Zone Configuration Time Zone: Enter your time zone. Default = UTC (Universal Coordinated Time, Universal Time). See the following Web site for Time Zone information: http://wwp.greenwichmeantime.com/info/current-time.htm Time Zone Offset: Enter +/- hh:mm. Default = +00:00. Offset is the amount of time varying from the standard time of a Time Zone. Daylight Configuration Daylight Saving: Enables/disables Daylight Saving mode. The default is Enable.
Chapter 3 – Using the Web Management Software Add Static Routes IP packets destined for the network indicated in the drop down box are routed to the IP address in the box pointed to by the arrow. The networks in the drop down box can be defined under the ‘Networks & Services’ tab. Static Route: Select a static route from the drop down list box, and then click Add. The new route displays at the bottom of the screen.
Chapter 3 – Using the Web Management Software PPP PPP > PPP Configuration NAT Configuration NAT Enable/disable NAT (Network Address Translation). The default is Enable. If NAT is enabled: Your LAN can use one set of IP addresses for internal traffic and a second set of addresses for external traffic. In other words, the router with NAT does the simple IP routing between the LAN interface and the WAN interface. NAT hides the LAN address behind a single IP address on the wireless side.
Chapter 3 – Using the Web Management Software Note: For routing to take effect, save the configuration after enabling it. It won’t be effective on the fly at runtime. PPP General PPP Enable/disable PPP. The default is Disable. When enabled, the unit functions as a router. PPP must be disabled to access the integrated cellular modem directly using telnet port 5000. If PPP is enabled, you cannot access the integrated cellular modem. Dial-on-Demand: Enable/disable Dial-on-Demand. The default is Disable.
Chapter 3 – Using the Web Management Software For EVDO models, the Dial Number is #777 Dial Prefix: Set the modem dial prefix. The default is ATDT. Connect String: Set the modem Connect String. The default is CONNECT. APN: Enter the APN (Access Point Name). For more information on APN, refer to Access Point Names. Init String 1-4: Configure the modem init strings. You can set up to 4 modem initialization strings. Baud Rate: Baud Rate only displays on certain models and is set at 230.
Chapter 3 – Using the Web Management Software from LAN: The default is disable. When enabled, the router will reconnect when it sees IP traffic on the LAN that is needed to be routed. If this feature is disabled, Dial-on-Demand initiates a PPP connection to the Internet only from the WAN, not from the LAN. Init Strings: Configure the router initialization string. This initialization string is specific to the installed integrated cellular modem.
Chapter 3 – Using the Web Management Software PPP > Wakeup-On-Call Examples Example 1 – Determine if Router Support Incoming Calls and Caller ID 1. On the PPP > PPP Configuration screen, make sure that PPP is Disabled. 2. On the PPP > Wakeup-on-Call screen, make sure that Wakeup-on-Call is Disabled. 3. Open a command prompt by clicking the Start button and selecting Run. 4. Type CMD to open the command window. Click OK. 5. When the command window opens, telnet to the router.
Chapter 3 – Using the Web Management Software ● All Init Strings should be empty. Caller ID Configuration ● Enter the string RING to the Caller ID list. ● Click Add to save the string to the Caller ID list. 3. Click Save & Restart to save all the settings and reboot. Example 3 – Set Up the Ethernet Router to Activate on Matching Caller IDs Only: 1. On the PPP > PPP Configuration screen, set up the following parameters and click Submit. PPP General ● Make sure that PPP is enabled.
Chapter 3 – Using the Web Management Software PPP > Power-On Configuration The Power-On Configuration feature allows you to set an initialization string that will be sent to the router upon boot up. Power-On Init String Configuration Power-On Init String: Note: You can enter a string of 0 to 40 characters that will be sent to the router upon boot up. All commands will initialize before you proceed with regular PPP related activity.
Chapter 3 – Using the Web Management Software AT+CREG? Notes: Network Registration You can also retrieve the integrated cellular modem information without using a browser: Make a TCP connection to port 80 (same as the Web Admin port) and send data as: GET /atinfor.html HTTP/1.1 Then press Enter twice. Refer to the AT Command Reference Guide for other commands. Networks & Services Networks & Services > Network Configuration Networks or Hosts can be added here.
Chapter 3 – Using the Web Management Software When you click Add, the defined network displays at the bottom of the screen. Networks & Services > Service Configuration On this screen you can specify the standard set of well known services available on the system. These services enable the configuration of the user-defined services. The options to Delete or Edit a service after it has been defined and added are available by using the table at the bottom of the screen. Multi-Tech Systems, Inc.
Chapter 3 – Using the Web Management Software Service Configuration Enter the Name, Protocol, Source Port/Client, and Destination Port/Server for the new Service and click Add. The new service displays at the bottom of the screen. Notes: A Service Name: ● Cannot be edited. ● If used in another configuration, cannot be deleted. ● Changes are reflected in all the configurations in the Web Management software where they are used.
Chapter 3 – Using the Web Management Software To (Host/Networks): Enter the network/host to which the packet must send for the filter rule to match. The Any option, which matches all IP addresses regardless of whether they are officially assigned addresses or private addresses, may also be entered. The network/host must be pre-defined in the Networks section. Action: Enter the action that the packet filter executes if the rule matches any traffic traversing the firewall.
Chapter 3 – Using the Web Management Software Click Save after making changes. The defined DNAT configuration displays at the bottom of the screen. Delete or edit settings by clicking the Edit or the Delete buttons. Packet Filters > DNAT Example Set Up DNAT and Port Forwarding to an Internal Device Note: The internal device can be camera, meter, security device, etc. For this example, assume the device is on a LAN with an IP address of 192.168.2.100 and the port to access the device is port 7700. 1.
Chapter 3 – Using the Web Management Software 5. Click Save and Restart once you have completed and submitted all the screens on which you have made changes. Packet Filters > Advanced Connection Tracking H323: Enable/disable the forwarding of H323 packets across the firewall. Default is disabled. PPTP: Enable/disable PPTP Packet Pass-through (PPTP NAT support). Default is disabled.
Chapter 3 – Using the Web Management Software GRE Tunnels GRE tunneling and GRE routing together are referred to Generic Routing Encapsulation (GRE). GRE Routing is an integral part of GRE tunneling. First, the GRE Tunnels are created using the GRE Tunnel Configuration. Then the routes for the remote networks that are to be routed through a tunnel need to be specified in the GRE Routes Configuration.
Chapter 3 – Using the Web Management Software GRE Tunnels > GRE Routes Configuration GRE Routes Configuration Remote Network: Select the remote network for which the traffic destined to it must be routed through the given tunnel. Tunnel Name: Select the name of the tunnel through which the traffic will be routed. Note: To add a tunneled route, the remote network and the tunnel must have been defined in Network Configuration.
Chapter 3 – Using the Web Management Software General Configuration DHCP (Dynamic Host Configuration Protocol) is a protocol that allows individual devices on an IP network to get their own network configuration information (IP address, subnet mask, broadcast address, etc.) from a DHCP server. The overall purpose of DHCP is to make it easier to administer a large network. DHCP: Enable/disable the DHCP server. Subnet: Enter the subnet address.
Chapter 3 – Using the Web Management Software DHCP Fixed Configuration The DHCP server can be made to assign a fixed IP address for a particular user by identifying the MAC address. This binding can be made permanent by configuring it here. The same IP address will not be used for any DHCP client with a different MAC address, even if there is no active DHCP connection with that IP address. MAC Address: Enter the MAC address to which the specified IP address binds.
Chapter 3 – Using the Web Management Software IPSec The IPSec (IP Security) protocol suite, based on modern cryptographic technologies, provides security services like encryption and authentication at the IP network layer. It secures the whole network traffic providing guaranteed security for any application using the network. It can be used to create private secured tunnels between two hosts, two security gateways, or a host and a security gateway. Up to three tunnels can be active at any given time.
Chapter 3 – Using the Web Management Software Manual Connection Click Add for Manual Connection to access the Manual Connection setup. Add IKE Connection Add an IKE Connection Connection Name Enter a text name that will identify the connection for you. Compression Check the compression checkbox to enable IPCOMP, the compression algorithm. Perfect Forward Secrecy (PFS) Check the PFS checkbox to enable PFS, in which the newly generated keys are unrelated to the older keys. Default is enabled.
Chapter 3 – Using the Web Management Software Local LAN Internal subnet of the local security gateway for which the security services should be provided. If the router acts as a host, this should be configured as None. Remote Gateway IP Interface where the IPSec tunnel ends. In the case of a Road Warrior with a Dynamic IP address, this should be configured to ANY.
Chapter 3 – Using the Web Management Software Authentication Key The VPN firewall could use either MD5-96 or SHA1-96 for authentication. For example, MD5-96 could have a key of abcdefgh12345678. Authentication Protocol SHA1-96 MD5-96 Key Length Must be 20 characters Must be 16 characters Accepted Characters Alphanumeric Alphanumeric Encryption Method Select the encryption method. Options include: 3DES, AES-128, AES-192, AES-256, and NULL (no encryption).
Chapter 3 – Using the Web Management Software NetBIOS Broadcast Check this option to enable broadcasts over the connection. It will allow computers on the network to share Microsoft file and printer sharing information. Click Save to save these settings. 53 Multi-Tech Systems, Inc.
Chapter 3 – Using the Web Management Software Tools Tools > Tools DDNS DDNS Force Update: Click Update to update the DDNS server with your current dynamically assigned IP address. DDNS Status: Click Refresh to display the DDNS Status after a forced update. Modem Reset Modem: Click Reset to reset the integrated cellular modem. Tools > Firmware Upgrade Firmware Upgrade Use this page to update router firmware. Go to multitech.com/support.go to check for firmware updates.
Chapter 3 – Using the Web Management Software displays in the text box. Make sure you select the correct BIN file; otherwise, your router can become inoperable. Then click Upgrade. When upgrade is completed, the program returns to the main login screen. Notes: ● The new firmware is written into the flash memory. ● Firmware upgrades take at least 4 minutes while the firmware is downloaded. Do not cycle power during this time.
Chapter 3 – Using the Web Management Software Statistics & Logs Statistics & Logs > System Information This image shows an example of Statistics & Logs System information Multi-Tech Systems, Inc.
Chapter 3 – Using the Web Management Software Statistics & Logs > Ethernet This image shows an example of Ethernet statistics. 57 Multi-Tech Systems, Inc.
Chapter 3 – Using the Web Management Software Statistics & Logs > PPP This image shows an example of PPP statistics when PPP is enabled. Multi-Tech Systems, Inc.
Chapter 3 – Using the Web Management Software Statistics & Logs > PPP Trace This image shows an example of PPP trace messages. Statistics & Logs > DHCP Statistics This image shows an example of DHCP statistics. Statistics & Logs > GRE Statistics This page displays active tunnel statistics. 59 Multi-Tech Systems, Inc.
Chapter 3 – Using the Web Management Software Statistics & Logs > Modem Information This image shows the modem commands currently set on the PPP > Modem Commands page along with commands results. Statistics & Logs > Service Status This page displays the service status summary. Statistics & Logs > TCP/UDP Client Live Log This page displays the TCP/UDP Client Live Log. Statistics & Logs > TCP/UDP Server Live Log This screen displays the TCP/UDP Server Live Log. Multi-Tech Systems, Inc.
Chapter 3 – Using the Web Management Software Statistics & Logs > IPSec Live Log This screen displays the IPSec Live Log. Statistics & Logs > IPSec Log Traces This screen displays the IPSec Log Traces. 61 Multi-Tech Systems, Inc.
Appendix A – Commonly Supported Subnets Reference Table This table lists commonly supported Subnets organized by Address. Network Number Hosts Available Broadcast Address 255.255.255.128 N.N.N.0 N.N.N.1-126 N.N.N.127 /25 N.N.N.128 N.N.N.129-254 N.N.N.255 Network Number Hosts Available Broadcast Address 255.255.255.192 N.N.N.0 N.N.N.1-62 N.N.N.63 /26 N.N.N.64 N.N.N.65-126 N.N.N.127 N.N.N.128 N.N.N.129-190 N.N.N.191 N.N.N.192 N.N.N.193-254 N.N.N.
Appendix A – Commonly Supported Subnets Reference Table N.N.N.72 N.N.N.73-78 N.N.N.79 N.N.N.80 N.N.N.81-86 N.N.N.87 N.N.N.88 N.N.N.89-94 N.N.N.95 N.N.N.96 N.N.N.97-102 N.N.N.103 N.N.N.104 N.N.N.105-110 N.N.N.111 N.N.N.112 N.N.N.113-118 N.N.N.119 N.N.N.120 N.N.N.121-126 N.N.N.127 N.N.N.128 N.N.N.129-134 N.N.N.135 N.N.N.136 N.N.N.137-142 N.N.N.143 N.N.N.144 N.N.N.145-150 N.N.N.151 N.N.N.152 N.N.N.153-158 N.N.N.159 N.N.N.160 N.N.N.161-166 N.N.N.167 N.N.N.168 N.N.N.
Appendix A – Commonly Supported Subnets Reference Table N.N.N.120 N.N.N.121-122 N.N.N.123 Network Number Hosts Available Broadcast Address N.N.N.124 N.N.N.125-126 N.N.N.127 N.N.N.128 N.N.N.129-130 N.N.N.131 N.N.N.132 N.N.N.133-134 N.N.N.135 N.N.N.136 N.N.N.137-138 N.N.N.139 N.N.N.140 N.N.N.141-142 N.N.N.143 N.N.N.144 N.N.N.145-146 N.N.N.147 N.N.N.148 N.N.N.149-150 N.N.N.151 N.N.N.152 N.N.N.153-154 N.N.N.155 N.N.N.156 N.N.N.157-158 N.N.N.159 N.N.N.160 N.N.N.161-162 N.N.N.
Appendix B – Regulatory Information EMC, Safety, and R&TTE Directive Compliance The CE mark is affixed to this product to confirm compliance with the following European Community Directives: Council Directive 2004/108/EC of 15 December 2004 on the approximation of the laws of Member States relating to electromagnetic compatibility; and Council Directive 2006/95/EC of 12 December 2006 on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage li
Appendix B – Regulatory Information EMC Requirements for Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Reglement Canadien sur le matériel brouilleur. This device complies with Industry Canada RSS Appliance radio exempt from licensing. The operation is permitted for the following two conditions: 1. the device may not cause harmful interference, and 2.
Appendix B – Regulatory Information REACH Statement Registration of Substances After careful review of the legislation and specifically the definition of an “article” as defined in EC Regulation 1907/2006, Title II, Chapter 1, Article 7.1(a)(b), it is our current view Multi-Tech Systems, Inc. products would be considered as “articles”. In light of the definition in § 7.
Appendix B – Regulatory Information 1Lead usage in some components is exempted by the following RoHS annex, therefore higher lead concentration would be found in some modules (>1000 PPM); –Resistors containing lead in a glass or ceramic matrix compound.
Appendix B – Regulatory Information Information on HS/TS Substances According to Chinese Standards (in Chinese) 依照中国标准的有毒有害物质信息 根据中华人民共和国信息产业部 (MII) 制定的电子信息产品 (EIP) 标准－中华人民共和国《电子信息产品污染控制管理办法》（第 39 号），也称作中国 RoHS，下表列出了 Multi-Tech Systems, Inc.
Index A Access Point Name AH Key Authentication Algorithms Auto Dialout configuration Autodiscovery configuration 20 52 51 26 26 GRE tunnel configuration GRE tunneling 45 45 H H323 packets connection tracking HTTP authentication HTTP configuration B Broadcast timer Browse File for Upgrade in Tools Browse File to Load Configuration I 27 55 55 C Caller ID for Wakeup on Call 35 China’s Administrative Measures on the Control of Pollution 68 ICMP configuration ICMP Keep Alive Check IP Configuration IP Se
Index System domain name S Save configuration in Tools Screen parts Select encryption method Server Port Service Configuration SNTP configuration Static Routes configuration Statistics & Logs > DHCP Statistics Statistics & Logs > Ethernet Statistics & Logs > Modem Information Statistics & Logs > PPP Subnets Supported Subnets Syslog configuration 71 55 23 52 27 40 29 30 59 57 60 58 62 62 26 28 T Time zone configuration Tools 30 54 U UDP 41 W Wakeup on Call Wakeup on Call Examples WEEE Directive Wiz
