Full Product Manual

ManualsBrandsmyTouchSmart ManualsElectricalSimple Set Plug-In Dual Digital Outdoor Timer with 2 Grounded Outlets

II. Preset schedules

There are 3 pre-programmed times

that run individually or simultaneously.

Choose from the following:

“evening” (5pm-12am)

“morning” (5am-8am)

“all night” (6pm-6am).

When a preset or custom program

is chosen, the blue LED indicator

light will turn on.

If a preset schedule does not ﬁt your

needs, a custom on/o time can be used

to modify the preset. Example: Using “evening”

(5pm-12am) and adding a “my o

time” of

10pm will create a 5pm-10pm timer

schedule.

III. Countdown

This feature turns the

light on for a set period

of time and turns it o

when time expires.

Press “countdown,” then use up

( ) and down ( ) arrows to set

from 1 minute to 24 hours. Once

you reach your desired time setting,

simply walk away and the timer will

begin counting down. Your last time

setting will be remembered the next

time you use the countdown feature.

Note: When daylight savings time occurs use the up

( ) and down ( ) arrows to adjust the time by 1 hour.

This device complies with part 15 of the FCC and Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1 this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may

cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modiﬁcations to this equipment. Such modiﬁcations could void the user’s authority

to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment o and on, the user is encourage to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAN ICES-3(B)/NMB-3(B)

1. Setup

If no numbers are visible on-screen, plug timer into an

outlet and let timer charge for 1 hour. Once charged,

press the reset (

) button in the lower right corner

using a toothpick or pencil.

2. Set the time

Use up ( ) and down ( )

arrows to set current time,

take note of AM or PM time.

3. Programming Options

Set your custom on & o time

and/or pick any of the presets

that suit your schedule!

I. Choose your custom on/o times

Press “my on time,” then use up ( )

and down ( ) arrows to set on time.

Press “my o time,” then use up ( )

and down ( ) arrows to set o time.

(If you set the “my on time” earlier

than the current time, it will not turn

on until the next day at the time

scheduled. Use the Countdown to

turn on the timer if needed

immediately.) When using “my on”

and “my o” times make sure the

blue light is lit next to the button.

The blue lights will only illuminate

when plugged into a wall outlet.

Mounting /Installation

1. Mount the timer on a wall near a GFCI receptacle using a screw or nail. Timer must be mounted in a vertical

position with the outlets facing downwards at least 4ft. above ground level. Screw or nail head must extend at

least 3/16” out from the wall (nails or screws not included).

2.Hang the timer, from the hole at the top of the unit.

MADE IN CHINA

Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.

This Jasco product comes with a 1-year limited warranty.

Visit www.byjasco.com for warranty details.

Questions? Contact us at 1-800-654-8483 between 7:00AM–8:00PM CST.

26898-P2 VERSION 01 10/11/16

Total ratings for both outlets:

125V 50/60 Hz

15A 1875 General Purpose/Resistive

10A 1250W Tungsten

1/2 HP

Works with dimmable

LED and CFL bulbs.

Outdoor/Indoor

Simple Set

Plug-In Timer

GE 53120

RISK OF ELECTRIC SHOCK

• PLUG DIRECTLY INTO

A GFCI PROTECTED

ELECTRICAL OUTLET

• UNPLUG TIMER

BEFORE CLEANING

• FULLY INSERT PLUG

• KEEP AWAY FROM CHILDREN

• NOT FOR WATER IMMERSION

• SUITABLE FOR INDOOR

AND OUTDOOR LOCATIONS,

STORE INDOORS WHILE

NOT IN USE.

RISK OF FIRE

• DO NOT USE TO CONTROL

APPLIANCES THAT CONTAIN

HEATING ELEMENTS (COOKING

APPLIANCES, HEATERS,

IRONS, ETC.)

• DO NOT EXCEED

ELECTRICAL RATINGS

• RATINGS ARE FOR BOTH

OUTLETS COMBINED

• DO NOT USE IF DEVICE

OR CORD IS DAMAGED.

• DO NOT USE WITH AN

EXTENSION CORD

WARNING

Summary of content (2 pages)

PAGE 1
Outdoor/Indoor Simple Set Plug-In Timer Mounting /Installation 1. Mount the timer on a wall near a GFCI receptacle using a screw or nail. Timer must be mounted in a vertical position with the outlets facing downwards at least 4ft. above ground level. Screw or nail head must e xtend at least 3/16” out from the wall (nails or screws not included). 2.Hang the timer, from the hole at the top of the unit. 1.
PAGE 2
Exterior y Interior Fácil de Programar Temporizador Enchufable Montaje/instalación 1. Con un tornillo o clavo, instale el temporizador en una pared cerca de un tomacorriente GFCI. Temporizador debe ser montado en una posición vertical con las tomas de corriente hacia abajo al menos 1.3 metros sobre el nivel del suelo. La cabeza del tornillo o del clavo se debe extender al menos 3/16” fuera de la pared (tornillo o clavo no incluido). 2.