Operation Manual

ManualsBrandsNAD ManualsAudioVISO THREE

CD-R AND CD-RW AUDIO DI SCS

The VISO THREE can playback CD-R or CD-RW audio discs that have been

recorded on a computer or CD recorder. The quality of CD-R or CD-RW

audio discs varies widely which may aect playability. Some factors that

aect playability:

• The quality of the disc itself. Generally speaking, CD-R or CD-RW blanks

from well-renowned companies give better results than unbranded

ones.

• The quality of CD-recorder or computer CD re/writer. Some recorders

and writers produce better results than others.

• The CD-R and CD-RW were created with high-speed writing. In general,

the quality of a CD-R or CD-RW is better when produced at a lower

speed against a higher speed on the same recorder or re/writer.

PLAYING MP3/WMA FILES

The VISO THREE can play MP3/WMA formatted recordings on CD-R or CD-

RW discs. You may mix any of the le types on the disc. Refer to SELECTING

FOLDERS OR FILES (USB, CD-R/-RW) at the USB mode section below for

MP3/WMA playability procedure.

PROGRAMMING ( CD/USB)

The program function enables you to store your favorite tracks from any

disc in the player memory. When programming a sequence of tracks, the

VISO THREE must be in STOP mode. Using the VR3 remote control, enter

your desired program sequence through the following steps

1 Press [PROG]. The VFD will show

Program��1��

T0000��

The “0000” in the “T0000” keeps on blinking, meaning that the player is

awaiting the rst Program entry.

2 Use the Direct-Entry numeric keypad buttons to enter the rst track in

your planned sequence. For example, press “2” and then [ENTER]. The

VFD will briey show

Program��1��

T0002��

3 The display will revert to show

Program��2��

T0000��

The “0000” in the “T0000” keeps on blinking, meaning that the player

is awaiting the second Program entry. For example, press “4” and then

[ENTER]. Upon entering the second track, the VFD will again briey

show

Program��2��

T0004��

4 Repeat steps 2 and 3 to select and store other track numbers in

memory, up to a maximum of 32 entries. If you attempt to program

more than 32 tracks or les, “Program Full” will be displayed in the VFD.

Program Full��

T0006��

5 Press [PROG] to end or nalize the program – the VFD will show the last

programmed number and track.

6 Press [ ] (Play) to start program playback.

NOTES

• The procedure for programming MP3/WMA les is the same as above.

• If you want to select le number “119” in a disc where there are 100 or

more MP3/WMA les, press “1” twice and then “9.”

• Pressing [STOP] button at any time during the programming procedure

will put to a STOP the sequence and clear all the currently programmed

tracks or les. VFD will revert back to displaying the total number of

tracks and total playback time for audio CD and total number of les for

MP3/WMA.

• Pressing [STOP] button twice during program playback will delete the

whole program list.

REVIEW PROGRAM LIST

1 Initiate review of your programmed entries by pressing [PROG].

2 The VFD will show the rst Program Number.

3 Press [ENTER] repeatedly to step through the program sequence. You

will have reached the end of the program sequence when “Program

End” is displayed at the VFD.

EDIT PROGRAM LIST

1 Initiate editing of your programmed entries by pressing [PROG].

2 The VFD will show the rst Program Number.

3 Press [ENTER] repeatedly to step through the program sequence. Stop

at the program sequence you want to edit.

4 To change the programmed track of the particular sequence, use the

Direct-Entry numeric keypad buttons. Press [ENTER].

5 Press [PROG] to end or nalize the program.

DELETE PROGRAM

Initiate editing of your programmed entries by pressing [PROG].

1 To delete a particular programmed track/le, press repeatedly

[ENTER] key until the desired programmed sequence is reached. Press

VR3’s [CLEAR] key once and the track/le in the particular sequence

is deleted. The program sequence will adjust accordingly as a

programmed track/le is deleted.

2 To clear the program memory, perform any of the following steps

• During programming mode, press [STOP] once.

• During program playback, press [STOP] twice.

• Press [OPEN/CLOSE] to open the disc tray (CD mode).

OPERATIO N

USING THE VISO THREE  CD MODE

ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ