本書は製品とともに大切に保管してください N8403-017 1000BASE-T 接続ボード(2ch) ユーザーズガイド まえがき このたびは、N8403-017 1000BASE-T 接続ボードをお買い上げいただきまことにありがとうございます。 本書は、N8403-017 1000BASE-T 接続ボード(以下「本製品」と呼びます)を正しく、安全に設置、使用 するための手引きです。本製品を取り扱う前に必ずお読みください。また、本製品を使用する上でわからな いこと、不具合が起きたときにもぜひご利用ください。本書は、必要な時にすぐに参照できるように必ずお 手元に保管してください。 本製品を取り付ける CPU ブレードの取り扱いについての説明は、CPU ブレードに添付のユーザーズガイド を参照してください。また、本製品を取り扱う前に「安全上のご注意」、 「使用上のご注意」を必ずお読みく ださい。
商標について Microsoft と そ の ロ ゴ お よ び Microsoft Windows, Windows, Windows Server 2003 は 米 国 Microsoft Corporation の米国およびその他の国における登録商標です。 記載の会社名および商品名は各社の商標または登録商標です。 ご注意 (1) 本書の内容の一部または全部を無断転載することは禁止されています。 (2) 本書の内容に関しては将来予告なしに変更することがあります。 (3) NECの許可なく複製・改変などを行うことはできません。 (4) 本書は内容について万全を期して作成いたしましたが、万一ご不審な点や誤り、記載もれなどお気づきのことが ありましたら、お買い求めの販売店にご連絡ください。 (5) 運用した結果の影響については(4)項にかかわらず責任を負いかねますのでご了承ください。
このユーザーズガイドは、必要なときすぐに参照できるように必ずお手元に保管してください。 「安全上のご注意」および「使用上のご注意」を必ずお読みください。 安全上のご注意 ~ 必ずお読みください ~ 本製品を安全に正しくご使用になるために必要な情報が記載されています。 安全にかかわる表示 本書では危険の程度を表す言葉として、「警告」と「注意」という用語を使用しています。それぞれの 用語は次のような意味を持つものとして定義されています。 警 告 人が死亡する、または重傷を負うおそれがあることを示します。 注 意 火傷や怪我などを負うおそれや物的損害を負うおそれがあることを示します。 表示は次の3種類の記号を使って表します。それぞれの記号は次のような意味を持つものものとし て定義されています。 (例) 注意の喚起 この記号は危険が発生するおそれがあることを表します。記号 の中の絵表示は危険の内容を図案化したものです。 (感電注意) (例) 行為の禁止 行為の強制 この記号は行為の禁止を表します。記号の中や近くの絵表示 は、してはならない行為の内容を図案化したものです。 この記号は行為の強制
安全上のご注意 本製品を安全にお使いいただくために、ここで説明する注意事項をよく読んでご理解し、安全にご 活用ください、記号の説明については巻頭の「安全にかかわる表示」の説明をご参照ください。 警 告 人命に関わる業務や高度な信頼性を必要とする業務には使用しない 本製品は、医療機器、原子力設備や機器、航空宇宙機器、輸送設備や機器など、人命に関わる設 備や機器および高度な信頼性を必要とする設備や機器などへの組み込みやこれら機器の制御な どを目的とした使用は意図されておりません。これら設備や機器、制御システムなどに本製品を 使用した結果、人身事故、財産損傷などが生じても当社はいかなる責任も負いかねます。 ご自分で分解、修理、改造はしない 本書に記載されている場合を除き、絶対に分解したり、修理・改造を行ったりしないでください。 装置が正常に動作しなくなるばかりでなく、感電や火災の危険があります。故障の際はお買い求 めの販売店または保守サービス会社にご連絡ください。 煙や異臭・異音がしたまま使用しない 万一、煙・異臭・異音などが生じた場合は、ただちに電源を OFF にして電源コードをコンセント から抜いてくださ
注 意 高温に注意する CPU ブレードの電源を OFF にした直後は、装置内の部品が高温になっています。十分に冷めたこ とを確認してから取り付け/取り外しを行ってください。 確実に接続する 本製品を CPU ブレードのメザニンスロットに接続するときは、確実に差し込んでネジを締めてく ださい。完全に差し込まなかったり、ネジを締めなかった場合、発煙や発火のおそれがあります。 中途半端に差し込まない 電源コードおよびケーブルは根本までしっかりと差し込んでください。中途半端に差し込むと接 触不良のため発熱し、火災の原因となることがあります。また差し込み部にほこりがたまり、水 滴などが付くと発熱し、火災の原因となるおそれがあります。 指定以外のインタフェースケーブルを使用しない インタフェースケーブルは、指定するものを使用し、接続する装置やコネクタを確認した上で接 続してください。指定以外のケーブルを使用したり、接続先を誤ったりすると、ショートにより 感電や火災を起こすことがあります。 インタフェースケーブルの取り扱いや接続について次の注意をお守りください。 ・破損したケーブルを使用しない。 ・ケーブルを踏まな
使用上のご注意 ~本製品を正しく動作させるために~ 本製品を使用するときに注意していただきたいことを次に示します。これらの注意を無視して、本 製品を使用した場合、資産(データやその他の装置)が破壊されるおそれがありますので必ずお守り ください。 本製品は大変静電気に弱い電子部品です。ブレード収納ユニットの金属フレーム部分などに触 れて身体の静電気を逃がしてから取り扱ってください。また、本製品の端子部分や部品を素手 で触ったり、直接机の上に置いたりしないでください。 本製品を落としたり物にぶつけたりしないでください、誤動作や故障するおそれがあります。 本書及び CPU ブレードのユーザーズガイドに記載されている説明をよくお読みになり、正しく 取り扱ってください。 CPU ブレードのメザニン拡張スロットにうまく本製品を取り付けられないときは、いったん本 製品を取り外してから取り付けなおしてください。過度の力を加えると破損するおそれがあり ますので注意してください。
本書について 本書は、N8403-017 1000BASE-T 接続ボードを正しくセットアップし、使用できるようにするための手引きで す。本製品を使用される前に本書をよくお読みになり、いつでも取り出せる場所に大切に保管してください。 本製品の移設の際は必ず本書も一緒に移設してください。 本書は、Windows などのオペレーティングシステムやキーボード、マウスといった一般的な入 出力装置などの基本的な取り扱いについて十分な知識を持ったユーザを対象として記載され ています。 本文中の記号 本文中では次の 3 つの記号を使用しています。それぞれの意味を示します。(「安全にかかわる表示」 については 1 ページをご参照ください) 重要 ヒ ン ト 本製品を取り扱う上で守らなけれ ばならない事柄や特に注意すべき 点を示します。 知っておくと役に立つ情報や、便 利なことなどを示します。 チ ェ ッ ク 本製品を取り扱う上で確認してお く必要がある点を示します。
梱包箱の中身について 梱包箱の中には本製品以外に色々な部品が入っています。「第2章 構成品」を参照し、全ての添付品がそろ っていることを確認してください。万一、足りないものや破損しているものがあった場合には、本製品をご 購入された販売店にご連絡ください。 保証について 本製品には「保証書」が添付されています。 「保証書」は販売店で所定事項を記入しお渡ししますので、記載 内容をご確認の上、大切に保管してください。保証期間中に故障した場合には、 「保証書」の記載内容に基づ き無償修理致します。保証後の修理については、ご購入された販売店もしくはご契約されている保守サービ ス会社にご相談ください。 製品寿命について 本製品の製品寿命は5年です。本製品の交換については、本製品をご購入された販売店もしくはご契約され ている保守サービス会社へご相談ください。 第三者への譲渡について 本製品を第三者に譲渡(または売却)する時には、必ず本書を含む全ての添付品をあわせて譲渡(または売 却)してください。 ソフトウェアに関しては、譲渡した側は一切の複製物を所有しないでください。また、インストールした装 置から削除した後、譲渡
目次 安全上のご注意 ~ 必ずお読みください ~ ...................................... 3 安全にかかわる表示 ................................................................... 安全上のご注意 ....................................................................... 使用上のご注意 ~本製品を正しく動作させるために~ .................................... 本書について ......................................................................... 本文中の記号 ......................................................................... 梱包箱の中身について ....................................................
1.本製品について 1-1.仕様 項目 仕様 LAN インターフェイス なし(外部ポート×2) 速度 ポート数 1000Gbps 2 形態 ブレード用タイプ1 メザニンカード 外形寸法 重量 動作電圧 消費電力 動作時 動作環境 保管時 115mm(幅)×100mm(奥行) 0.1kg 以下 3.3V 定常 1.5W 温度 0 ~ 45℃ 湿度 5 ~ 95% 温度-40 ~ 70℃ 湿度 5 ~ 95% 備考 LAN の接続には GbE スルーカ ードもしくは GbE インテリ ジェントスイッチ(L2)等の 本製品に対応するスイッチ モジュールが必要になりま す。 タイプ 1 もしくはタイプ 2 の メザニン拡張スロットに実 装可能です。 結露しないこと 1-2.
2.構成品 梱包箱にはコントローラボード以外に付属品が入っています。添付の構成品表を参照し全てそろって いることを確認してください。万一、足りないものや破損しているものがありましたら、販売店にご 連絡ください。 品名 1000BASE-T 接続ボード(2ch) 数量 1 備考 保証書 1 組込出荷時は添付されません。 本体装置の保証書に記載されます。 取扱説明書 1 本書 固定用ネジ 3 本装置を CPU ブレードに装着するためのネジ です 3.
4.
4-1.本製品の取り付け 次に示す手順に従って本製品を CPU ブレードに取り付けます。 注 意 高温に注意する CPU ブレードの電源を OFF にした直後は、装置内の部品が高温になっています。十分に冷めたこ とを確認してから取り付け/取り外しを行ってください。 確実に接続する CPU ブレードに取り付ける際は確実に接続してください。中途半端に取り付けると接触不良を起 こし、発煙や発火の原因となるおそれがあります。 1. 本製品を取り付ける CPU ブレードの電源が OFF(POWER ランプ消灯)になっていることを確認し ます。 重要 CPU ブレードの電源が ON(POWER ランプ点灯)になっている場合は、各オペレー ティングシステムの電源 OFF の処理を行った後、CPU ブレードの電源を OFF に してください。 2. CPU ブレードの説明書に従ってブレード収納ユニットから本製品を取り付ける CPU ブレードを 取り出します。 3.
4-2.CPU ブレードの取り付け CPU ブレードの説明書に従ってブレード収納ユニットに CPU ブレードに取り付けます。 注 意 高温に注意する CPU ブレードの電源を OFF にした直後は、装置内の部品が高温になっています。十分に冷めたこ とを確認してから取り付け/取り外しを行ってください。 確実に接続する CPU ブレードを取り付ける際は確実に接続してください。中途半端に取り付けると接触不良を起 こし、発煙や発火の原因となるおそれがあります。 4-3.
5.注意事項/困ったときの処理 本製品をご使用される際の注意事項及び困ったときの処理について、下記に記します。 該当する項目がある場合は、説明に従って正しく対処してください。 5-1.
Keep this manual with the product. N8403-017 1000BASE-T Adapter (2ch) User's Guide Preface Congratulations on your purchase of the N8403-017 1000BASE-T Adapter. This User’s Guide is intended to allow you to install and use the N8403-017 1000BASE-T Adapter (hereafter called the card) correctly and safely. Read this manual thoroughly before handling the card. In addition, refer to this guide to understand how to use the card or when a problem occurs.
Trademarks Microsoft, its logo, Microsoft Windows, Windows, and Windows Server 2003 are worldwide registered trademarks of Microsoft Corporation of the U.S.A. All company names and product names mentioned herein are trademarks or registered trademarks of their respective companies. Notes: (1) (2) (3) (4) (5) (6) No part of this manual may be reproduced in any form without the prior written permission of NEC Corporation. The contents of this manual may be revised without prior notice.
Keep this User's Guide handy for quick reference when necessary. Be sure to read this section carefully. NOTES ON USE - Always read the Notes - The following includes information necessary for proper and safe operation of the card. SAFETY INDICATIONS In the User’s Guide, "WARNING" or "CAUTION" is used to indicate a degree of danger. These terms are defined as follows: WARNING Indicates the presence of a hazard that may result in death or serious personal injury.
Symbols Used in This Manual Attentions Indicates a general notice or warning that cannot be specifically identified. Indicates that improper use may cause an electric shock. Indicates that improper use may cause personal injury. Indicates that improper use may cause fumes or fire. Prohibited Actions Indicates a general prohibited action that cannot be specifically identified. Do not disassemble, repair, or modify the server. Otherwise, an electric shock or fire may be caused.
Safety Indications This section provides notes on using your product safely. Read this section carefully to ensure proper and safe use of the product. For symbols, see "SAFETY INDICATIONS" provided earlier. WARNING Do not use this product for services where critical high availability may directly affect human lives.
CAUTION Avoid installation in extreme temperature conditions. Immediately after the server is powered off, its internal components such as hard disks are very hot. Leave the server until its internal components fully cool down before installing/removing any component. Connect firmly. Connect the product to the computer firmly. A loose connection can cause a contact failure and can lead to smoke or fire. Insert the power plug into the outlet as far as it goes.
Notes on Use - For Proper Operation - Note the following when you use the card. If you ignore the notes, your assets (including important data and/or other devices) may be damaged. The product is extremely sensitive to static electricity. Make sure to touch the metal frame of the Blade Enclosure to discharge static electricity from your body before handling the product. Do not touch the terminals or components of the product with your bare hands or place the product directly on a desk.
About This Manual This guide describes how to setup and use the N8403-017 1000BASE-T Adapter. Read this guide thoroughly before using the card and store it in a safe place for future reference. When transferring the product, always include this guide. This guide is intended for persons who are familiar with operating systems including Windows and fundamental operations of general-purpose I/O devices including the keyboard and mouse.
Transfer to Third Party Make sure to provide this manual and all the accessories along with the product to a third party. To transfer or sell any software application that comes with the product to a third party, the following requirements must be satisfied: All provided software applications must be transferred and no backup copies must be retained. Software applications must be uninstalled before transferring the product.
Contents Preface .................................................................... 16 NOTES ON USE - Always read the Notes - ................................ 18 Symbols Used in This Manual ......................................................... Safety Indications .................................................................. Notes on Use - For Proper Operation - ............................................... About This Manual ...................................................................
1. About N8403-017 1-1. Specifications Item Specifications Remarks LAN interface None (External port x2) To connect with the LAN, Switch modules corresponding to this product, such as 1Gb Pass-Through Card or 1Gb Intelligent L2 Switch, are required. Transfer rate Number of ports Type 1Gbps 2 Type 1 Mezzanine card for CPU blade Outside dimensions Weight Operating voltage Power consumption Operating Operating Environment Storage 115 mm (width) ×100 mm (depth) 0.1 kg max. 3.3V Stationary state: 1.
2. Components The package contains the items listed in the table below. Make sure that all the items are provided. If you find any component missing or damaged, contact your service representative. Name 1000BASE-T Adapter (2ch) User's Guide Fixing screws Qty 1 1 3 Remarks This guide. Screws to secure the card to the CPU blade.
3. Names and Functions of Sections MAC address Front view Rear view Mezzanine connector Fixing screws (x3) (1) Fixing screws Use these screws to secure the card to the spacer of the CPU blade. (2) MAC address Indicates the MAC address assigned to the card. The MAC address is equivalent to the 12-digit LAN address assigned to port 1 of the card. The LAN address of port 2 is "LAN address of port 1 + 1.
4. Setup Procedure Take the following steps to setup the card: Explained in this User's Guide Installing card See Page 30. Install the N8403-017 Adapter in the CPU blade. Installing CPU blade See Page 31. Install the CPU blade in the Blade Enclosure. Explained in the User's Guide of the CPU Blade Installing device driver See the User's Guide of the CPU blade. Install the appropriate device driver for your operating system.
4-1. Installation Take the following steps to install the card in the CPU blade: CAUTION Avoid installation in extreme temperature conditions. Immediately after the CPU blade is powered off, its internal components are very hot. Leave the CPU blade until its internal components fully cool down before installing/removing any component. Connect firmly. Connect the product to the computer firmly. A loose connection can cause a contact failure and can lead to smoke or fire. 1.
4-2. Installing CPU Blade Install the CPU blade in the Blade Enclosure according to the User's Guide of the CPU blade. CAUTION Avoid installation in extreme temperature conditions. Immediately after the CPU blade is powered off, its internal components are very hot. Leave the CPU blade until its internal components fully cool down before installing/removing any component. Connect firmly. Connect the product to the computer firmly.
5. Troubleshooting This section describes actions to take to resolve problems with the card. 5-1. Troubleshooting An error message appears while booting the server: Refer to the manual provided with the CPU blade. If the slot containing the card is assumed to be the error cause, check the following: An error occurred in the slot in which the card is installed. Reconnect the card. Notice If the same error message still appears, remove the card and install it in another mezzanine slot.