Projector M352WS/M302WS/M332XS User’s Manual The M302WS is not distributed in North America. Model No.
Ver. 1/12/13 • DLP is a trademark of Texas Instruments. • Apple, Mac, Mac OS, and MacBook are trademarks of Apple Inc. registered in the U.S. and other countries. • Microsoft, Windows, Windows Vista, Internet Explorer, .NET Framework and PowerPoint are either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. • Intel and Intel Core are trademarks of Intel Corporation in the U.S. and/or other countries.
Important Information Safety Cautions Precautions Please read this manual carefully before using your NEC projector and keep the manual handy for future reference. CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. CAUTION TO PREVENT SHOCK, DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Important Information WARNING TO CALIFORNIA RESIDENTS: Handling the cables supplied with this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. WASH HANDS AFTER HANDLING. RF Interference (for USA only) WARNING The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Display Solutions of America, Inc. in this manual.
Important Information WARNING • Do not cover the lens with the lens cap or equivalent while the projector is on. Doing so can lead to melting of the cap due to the heat emitted from the light output. • Do not place any objects, which are easily affected by heat, in front of the projector lens. Doing so could lead to the object melting from the heat that is emitted from the light output. • Do not spray flammable gas to get rid of dust and dirt that accumulate in the lens. Doing so could cause a fire.
Important Information • Do not splash water over the projector. Doing so can cause electrical shock or fire. If the projector gets wet, turn off the projector, unplug the power cord and have the projector serviced by a qualified service personnel. • Handle the power cord carefully. A damaged or frayed power cord can cause electric shock or fire. - Do not use any power cord other than the one supplied with the projector. - Do not bend or tug the power cord excessively.
Important Information Note for US Residents The lamp in this product contains mercury. Please dispose according to Local, State or Federal Laws. Lamp Replacement • Use the specified lamp for safety and performance. • To replace the lamp, follow all instructions provided on page 128. • Be sure to replace the lamp when the message [THE LAMP HAS REACHED THE END OF ITS USABLE LIFE. PLEASE REPLACE THE LAMP.] appears.
Important Information Power management function The projector has power management functions. To reduce power consumption, the power management functions (1 and 2) are factory preset as shown below. To control the projector from an external device via a LAN or serial cable connection, use the on-screen menu to change the settings for 1 and 2. 1. STANDBY MODE (Factory preset: NORMAL) To control the projector from an external device, select [NETWORK STANDBY] for [STANDBY MODE].
Table of Contents Important Information. ........................................................................................... i 1. Introduction............................................................................................................1 ❶ What’s in the Box?...........................................................................................................1 ❷ Introduction to the Projector............................................................................................
Table of Contents Checking Energy-Saving Effect [CARBON METER]...............................................32 ❺ Preventing the Unauthorized Use of the Projector [SECURITY]........................................33 ❻ Using the Computer Cable (VGA) to Operate the Projector (Virtual Remote Tool).......36 ❼ Operating Your Computer’s Mouse Functions from the Projector’s Remote Control via the USB Cable (Remote Mouse Function)...........................................................
Table of Contents ❼ Menu Descriptions & Functions [INFO.]......................................................................109 [USAGE TIME].......................................................................................................109 [SOURCE(1)].........................................................................................................110 [SOURCE(2)].........................................................................................................110 [WIRED LAN]...........
1. Introduction ❶ What’s in the Box? Make sure your box contains everything listed. If any pieces are missing, contact your dealer. Please save the original box and packing materials if you ever need to ship your projector.
1. Introduction ❷ Introduction to the Projector This section introduces you to your new projector and describes the features and controls. Congratulations on Your Purchase of the Projector This projector is one of the very best projectors available today. The projector enables you to project precise images up to 150 inches for short throw models across (measured diagonally) from your PC or Mac computer (desktop or notebook), VCR, DVD player, or document camera.
1. Introduction • Integrated RJ-45 connector for wired networking capability along with wireless networking capabilities An RJ-45 connector is standard. An optional USB Wireless LAN Unit is required for wireless LAN connection. • Software programs (User Supportware) contained in the supplied CD-ROM The supplied NEC Projector includes three programs: Virtual Remote Tool, Image Express Utility Lite (for Windows/ Mac OS), PC Control Utility Pro 4 (for Windows)/5 (for Mac OS).
1. Introduction About this user’s manual The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to review the user’s manual. This may save you time later on. At the beginning of each section of the manual you’ll find an overview. If the section doesn’t apply, you can skip it.
1. Introduction Comparative Table of Main Features The main features vary depending on the model as follows. Native Aspect Ratio Native Resolution (dots × lines*1) Screen Size Projection Distance Light output *2 *3 in OFF for ECO MODE Lamp Replacement Time (average) Lamp Model Lamp Wattage (AC) Zoom Focus Short-Throw Models with Wide Panel M352WS M302WS 16:10 Wide WXGA (1280 × 800) Short-Throw Model M332XS 4:3 Standard XGA (1024 × 768) 60" - 150" 22–58 inches/0.57–1.
1. Introduction ❸ Part Names of the Projector Front/Top [M352WS/M302WS/M332XS] Light Sensor (→ page 93) Controls (→ page 8) Focus Lever (→ page 23) Port Cover for Optional USB Wireless LAN Unit When using the optional USB Wireless LAN Unit, first remove the cover. (→ page 125) Lens Lens Cap Adjustable Tilt Foot (→ page 21) Security chain opening Attach an anti-theft device. The security chain opening accepts security wires or chains up to 0.18 inch/4.6 mm in diameter.
1. Introduction Rear [M352WS/M302WS/M332XS] Built-in Security Slot ( Lamp Cover (→ page 128) )* Intake Vent (→ page 127) Connection for cable cover (Left) Screw holes (→ page 137) Terminal Panel (→ page 9) Connection for cable cover (Right) Screw holes (→ page 137) AC Input Connect the supplied power cord’s three-pin plug here, and plug the other end into an active wall outlet. (→ page 16) Rear Feet (→ page 21) Monaural Speaker (20 W) * This security slot supports the MicroSaver ® Security System.
1. Introduction Top Features 12 4 3 8 9 6 5 13 7 10 11 1. (POWER) Button (→ page 17, 27) 2. POWER Indicator (→ page 16, 17, 27, 131) 3. STATUS Indicator (→ page 131) 4. LAMP Indicator (→ page 128, 131) 5. ECO Button (→ page 31) 6. SOURCE Button (→ page 19) 7. AUTO ADJ. Button (→ page 26) 1, 2 9. ▲▼◀▶ / Volume Buttons ◀▶ / Keystone Buttons ▲▼ (→ page 24, 26, 78) 10. ENTER Button (→ page 78) 11. EXIT Button (→ page 78) 12.
1. Introduction Terminal Panel Features 11 12 5 10 7 13 8 9 1. COMPUTER IN/ Component Input Connector (Mini D-Sub 15 Pin) (→ page 117, 119, 121) 2. COMPUTER AUDIO IN Mini Jack (Stereo Mini) (→ page 117, 119, 121) 3. HDMI 1 IN Connector (Type A) (→ page 117, 122) 4. HDMI 2 IN Connector (Type A) (→ page 117, 122) 5. USB-B Port (Type B) (→ page 42, 43) 6. MONITOR OUT (COMP.) Connector (Mini D-Sub 15 Pin) (→ page 121) 7.
1. Introduction ❹ Part Names of the Remote Control 1 2 5 8 9 11 15 14 18 19 22 23 24 27 33 3 4 6 7 10 16 13 12 17 20 21 26 28 25 29 30 31 32 1. Infrared Transmitter (→ page 11) 22. ENTER Button (→ page 78) 2. POWER ON Button (→ page 17, 27) 23. D-ZOOM (+)(–) Button (→ page 29) 3. STANDBY Button (→ page 27) 24. MOUSE L-CLICK Button* (→ page 42) 4. SOURCE Button (→ page 19) 25. MOUSE R-CLICK Button* (→ page 42) 5, 6.
1. Introduction Battery Installation 1 Press firmly and slide the battery cover off. 2 Install new batteries (AAA). Ensure that you have the batteries’ polarity (+/−) aligned correctly. 3 Slip the cover back over the batteries until it snaps into place. Do not mix different types of batteries or new and old batteries. EN OP EN OP Remote Control Precautions • • • • • • • • • Handle the remote control carefully. If the remote control gets wet, wipe it dry immediately.
1. Introduction ❺ Operating Environment for Software Included on CD-ROM Names and Features of Bundled Software Programs Name of software program Virtual Remote Tool (Windows only) Features This is a software program used to control the power ON/OFF and source selection of the projector from your computer by using the supplied computer cable (VGA) and others.
1. Introduction Operating Environment The following is the operating environment for Image Express Utility Lite. For the operating environment of other software program, refer to the help function of each software program.
1. Introduction [Mac] Supported OS Mac OS X v10.6, v10.7, v10.8 Processor (CPU) Intel® Core™ Duo processor 1.5 GHz or higher required Intel® Core™ 2 Duo processor 1.
2. Projecting an Image (Basic Operation) This section describes how to turn on the projector and to project a picture onto the screen.
2. Projecting an Image (Basic Operation) ❷ Connecting Your Computer/Connecting the Power Cord 1. Connect your computer to the projector. This section will show you a basic connection to a computer. For information about other connections, see “6. Installation and Connections” on page 117. Connect the computer cable (VGA) between the projector’s COMPUTER IN connector and the computer’s port (mini D-Sub 15 Pin). Turn two thumb screws of both connectors to fix the computer cable (VGA). 2.
2. Projecting an Image (Basic Operation) ❸ Turning on the Projector 1. Remove the lens cap. Lens cap 2. Press the (POWER) button on the projector cabinet or the POWER ON button on the remote control. The POWER indicator will turn to blue and the projector will become ready to use. TIP: • When the message “Projector is locked! Enter your password.” is displayed, it means that the [SECURITY] feature is turned on.
2. Projecting an Image (Basic Operation) Note on Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one of the menu languages. To select a menu language, follow these steps: 1. Use the ▲, ▼, ◀ or ▶ button to select one of the languages from the menu. 2. Press the ENTER button to execute the selection. After this has been done, you can proceed to the menu operation.
2. Projecting an Image (Basic Operation) ❹ Selecting a Source Selecting the computer or video source NOTE: Turn on the computer or video source equipment connected to the projector. Detecting the Signal Automatically Press the SOURCE button once. The projector will search for the available input source and display it. The input source will change as follows: COMPUTER → HDMI1 → HDMI2 → VIDEO → USB-A → LAN → USB-B → COMPUTER → ...
2. Projecting an Image (Basic Operation) ❺ Adjusting the Picture Size and Position Use the adjustable tilt foot, the zoom function or the focus ring to adjust the picture size and position. In this chapter drawings and cables are omitted for clarity.
2. Projecting an Image (Basic Operation) Adjust the Tilt Foot 1. Lift the front edge of the projector. CAUTION: Do not try to touch the exhaust vent during Tilt Foot adjustment as it can become heated while the projector is turned on and after it is turned off. 1 2. Push up and hold the Adjustable Tilt Foot Lever on the front of the projector to extend the adjustable tilt foot. 2 3. Lower the front of the projector to the desired height. Adjustable Tilt Foot 4.
2. Projecting an Image (Basic Operation) Zoom The image size can be adjusted electronically from the menu. To do so, follow the steps below. Adjusting with the ZOOM button on the remote control 1. Press the ZOOM button. The DIGITAL ZOOM bar will be displayed. 2. Press the ◀ or ▶ button to adjust the image size. 3. Press the EXIT button. The DIGITAL ZOOM bar will be closed.
2. Projecting an Image (Basic Operation) Focus Use the FOCUS lever to obtain the best focus.
2. Projecting an Image (Basic Operation) ❻ Correcting Keystone Distortion Manually If the screen is tilted vertically, keystone distortion becomes large. Automatic Keystone Correction function is turned on at the time of shipment. To correct keystone distortion manually, proceed with the following steps to correct keystone distortion. NOTE: • The Keystone correction can cause an image to be slightly blurred because the correction is made electronically.
2. Projecting an Image (Basic Operation) Adjusting with the remote control 1. Press the KEYSTONE button. The Keystone bar will be displayed. 2. Use the ◀ or ▶ button to correct the keystone distortion. Adjust so that the right and left sides are parallel. 3. Press the EXIT button. The Keystone bar will be closed.
2. Projecting an Image (Basic Operation) ❼ Optimizing Computer Signal Automatically Adjusting the Image Using Auto Adjust Optimizing a computer image automatically. (COMPUTER) Press the AUTO ADJ. button to optimize a computer image automatically. This adjustment may be necessary when you connect your computer for the first time. [Poor picture] [Normal picture] NOTE: Some signals may take time to display or may not be displayed correctly.
2. Projecting an Image (Basic Operation) ❾ Turning off the Projector To turn off the projector: 1. First, press the (POWER) button on the projector cabinet or the STANDBY button on the remote control. The confirmation message will be displayed. 2. Secondly, press the ENTER button or press the (POWER) or the STANDBY button again. Power On Standby Steady blue light Steady red light After the projector turns off, the cooling fans keep operating for a while (Cooling-off time).
2. Projecting an Image (Basic Operation) ❿ After Use Preparation: Make sure that the projector is turned off. 1. Unplug the power cord. 2. Disconnect any other cables. • Remove the USB memory if it is inserted into the projector. 3. Retract adjustable tilt foot if extended. 4. Reattach the lens cap 1 2 ① Put the lens cap on the top of the lens. ② Push to cover the lens completely. CAUTION: Use caution when putting the projector in the soft case immediately after the projector has been operating.
3. Convenient Features ❶ Turning off the Image and Sound Press the AV-MUTE button to turn off the image and sound for a short period of time. Press again to restore the image and sound. The projector’s power-saving function will work 10 seconds after the image is turned off. As a result, the lamp power will be reduced. NOTE: • Even though the image is turned off, the menu still remains on the screen. • Sound from the AUDIO OUT jack (Stereo mini) can be turned off.
3. Convenient Features 2. Press the ▲▼◀▶ button. The area of the magnified image will be moved 3. Press the D-ZOOM (−) button. Each time the D-ZOOM (−) button is pressed, the image is reduced. NOTE: • The image will be enlarged or reduced at the center of the screen. • Displaying the menu will cancel the current magnification.
3. Convenient Features ❹ Changing Eco Mode/Checking Energy-Saving Effect Using Eco Mode [ECO MODE] The ECO MODE (NORMAL and ECO) increases lamp life, while lowering power consumption and cutting down on CO2 emissions. Four brightness modes of the lamp can be selected: [OFF], [AUTO ECO], [NORMAL] and [ECO] modes. [ECO MODE] Description [OFF] The lamp brightness is 100%.
3. Convenient Features Checking Energy-Saving Effect [CARBON METER] This feature will show energy-saving effect in terms of CO2 emission reduction (kg) when the projector’s [ECO MODE] is set to [AUTO ECO], [NORMAL], or [ECO]. This feature is called as [CARBON METER]. There are two messages: [TOTAL CARBON SAVINGS] and [CARBON SAVINGS-SESSION]. The [TOTAL CARBON SAVINGS] message shows the total amount of CO2 emission reduction from the time of shipment up to now.
3. Convenient Features ❺ Preventing the Unauthorized Use of the Projector [SECURITY] A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the projector cannot project an image. • The [SECURITY] setting cannot be cancelled by using the [RESET] of the menu. To enable the Security function: 1. Press the MENU button.
3. Convenient Features 7. Type in the same combination of ▲▼◀▶ buttons and press the ENTER button. The confirmation screen will be displayed. 8. Select [YES] and press the ENTER button. The SECURITY function has been enabled. To turn on the projector when [SECURITY] is enabled: 1. Press the POWER button. The projector will be turned on and display a message to the effect that the projector is locked. 2. Press the MENU button. 3. Type in the correct keyword and press the ENTER button.
3. Convenient Features To disable the SECURITY function: 1. Press the MENU button. The menu will be displayed. 2. Select [SETUP] → [INSTALLATION] → [SECURITY] and press the ENTER button. The OFF/ON menu will be displayed. 3. Select [OFF] and press the ENTER button. The SECURITY KEYWORD screen will be displayed. 4. Type in your keyword and press the ENTER button. When the correct keyword is entered, the SECURITY function will be disabled. NOTE: If you forget your keyword, contact your dealer.
3. Convenient Features ❻ Using the Computer Cable (VGA) to Operate the Projector (Virtual Remote Tool) Using the utility software “Virtual Remote Tool” included on the companion NEC Projector CD-ROM, Virtual Remote screen (or toolbar) can be displayed on your computer screen. This will help you perform operations such as projector’s power on or off and signal selection via the computer cable (VGA), serial cable, or LAN connection.
3. Convenient Features NOTE: • When [COMPUTER] is selected from your source selection, the Virtual Remote screen or the toolbar will be displayed as well as your computer screen. • Use the supplied computer cable (VGA) to connect the COMPUTER IN connector directly with the monitor output connector of the computer to use Virtual Remote Tool. Using a switcher or other cables than the supplied computer cable (VGA) may cause failure in signal communication. VGA cable connector: Pin Nos.
3. Convenient Features TIP: If the menu window will not be displayed, try the following procedure. For Windows 7 1. Click “start” on Windows. 2. Click “All Programs” → “Accessories” → “Run”. 3. Type your CD-ROM drive name (example: “Q:\”) and “LAUNCHER.EXE” in “Name”. (example: Q:\ LAUNCHER.EXE) 4. Click “OK”. The menu window will be displayed. 2 Click “Install Virtual Remote Tool” on the menu window. The installation will start.
3. Convenient Features TIP: Uninstalling Virtual Remote Tool Preparation: Exit Virtual Remote Tool before uninstalling. To uninstall Virtual Remote Tool, the Windows user account must have “Administrator” privilege (Windows 8, Windows 7 and Windows Vista) or “Computer Administrator” privilege (Windows XP). • For Windows 7/Windows Vista 1 Click “Start” and then “Control Panel”. The Control Panel window will be displayed.
3. Convenient Features Step 3: Start Virtual Remote Tool Start using the shortcut icon • Double-click the shortcut icon on the Windows Desktop. Start from the Start menu • Click [Start] → [All Programs] or [Programs] → [NEC Projector User Supportware] → [Virtual Remote Tool] → [Virtual Remote Tool]. When Virtual Remote Tool starts for the first time, “Easy Setup” window will be displayed.
3. Convenient Features Exiting Virtual Remote Tool 1 Click the Virtual Remote Tool icon on the Taskbar. The pop-up menu will be displayed. 2 Click “Exit”. The Virtual Remote Tool will be closed. Viewing the help file of Virtual Remote Tool • Displaying the help file using the taskbar 1 Click the Virtual Remote Tool icon on the taskbar when Virtual Remote Tool is running. The pop-up menu will be displayed. 2. Click “Help”. The Help screen will be displayed.
3. Convenient Features ❼ Operating Your Computer’s Mouse Functions from the Projector’s Remote Control via the USB Cable (Remote Mouse Function) The built-in remote mouse function enables you to operate your computer’s mouse functions from the supplied remote control when the projector is connected to a computer via a commercially available USB cable (compatible with USB 2.0 specifications). The Remote Mouse function works for the COMPUTER input while the computer screen is displayed.
3. Convenient Features ❽ Projecting Your Computer’s Screen Image from the Projector via the USB Cable (USB Display) Using a commercially available USB cable (compatible with USB 2.0 specifications) to connect the computer with the projector allows you to send your computer screen image to the projector for displaying. Power On/Off and source selection of the projector can be done from your computer without connecting a computer cable (VGA).
3. Convenient Features 5. Operate the control window. (6) (1) (2) (3) (4) (5) (1) (Source) ����� Selects an input source of the projector. (2) (Picture) ���� Turns on or off AV-MUTE (Picture mute), and turns on or off FREEZE (Freeze a picture). (3) (Sound) ����� Turns on or off AV-MUTE (Sound mute), play the sound and turns up or down the volume. (4) (Others) ����� Uses “Update”, “HTTP Server”*, “Settings” and “Information”. * The HTTP Server cannot be selected when a USB cable is connected.
3. Convenient Features ❾ Controlling the Projector by Using an HTTP Browser Overview The HTTP Server function provides settings and operations for: 1. Setting for wired/wireless network (NETWORK SETTINGS) To use wireless LAN connection, the optional USB Wireless LAN Unit is required. (→ page 124) To use wired/wireless LAN connection, connect the projector to the computer with a commercially available LAN cable. (→ page 123) 2.
3.
3. Convenient Features PICTURE: Controls the video adjustment of the projector. BRIGHTNESS ▲ ���� Increases the brightness adjustment value. BRIGHTNESS ▼ ���� Decreases the brightness adjustment value. CONTRAST ▲ �������� Increases the contrast adjustment value. CONTRAST ▼ �������� Decreases the contrast adjustment value. COLOR ▲ �������������� Increases the color adjustment value. COLOR ▼ �������������� Decreases the color adjustment value. HUE ▲ ������������������� Increases the hue adjustment value.
3. Convenient Features NETWORK SETTINGS • SETTINGS WIRED or WIRELESS SETTING Set for wired LAN or for wireless LAN. APPLY Apply your settings to wired LAN or wireless LAN. DHCP ON Automatically assign IP address, subnet mask, and gateway to the projector from your DHCP server. DHCP OFF Set IP address, subnet mask, and gateway to the projector assigned by your network administrator. IP ADDRESS Set your IP address of the network connected to the projector.
3. Convenient Features NETWORK TYPE Select communication method when using wireless LAN. INFRASTRUCTURE: Select this option when communicating with one or more equipment connected to the wireless LAN network via a wireless access point. AD HOC: Select this option when using the wireless LAN to directly communicate with a computer in peer-to-peer mode. SECURITY TYPE Turn on or off the encryption mode for secure transmission. When turn on the encryption mode, set WEP key or encrypted key.
3. Convenient Features • NAME PROJECTOR NAME Enter a name for your projector so that your computer can identify the projector. A projector name must be 16 characters or less. TIP: Projector name will not be affected even when [RESET] is done from the menu. HOST NAME Enter the hostname of the network connected to the projector. A host name must be 15 or less. DOMAIN NAME Enter the domain name of the network connected to the projector. A domain name must be 60 characters or less.
3. Convenient Features CRESTRON ROOMVIEW compatibility The projector supports CRESTRON ROOMVIEW, allowing multiple devices connected in the network to be managed and controlled from a computer or a controller. For more information, visit http://www.crestron.com Access to the HTTP server function, and make necessary settings for [CRESTRON] in [NETWORK SETTINGS]. • ROOMVIEW for managing from the computer. DISABLE Disables ROOMVIEW. ENABLE Enables ROOMVIEW.
3. Convenient Features ❿ Controlling the Projector over a LAN (PC Control Utility Pro 4/ Pro 5) Using the utility software “PC Control Utility Pro 4” and “PC Control Utility Pro 5” included on the companion NEC Projector CD-ROM, the projector can be controlled from a computer over a LAN. PC Control Utility Pro 4 is a program compatible with Windows. (→ this page) PC Control Utility Pro 5 is a program compatible with Mac OS.
3. Convenient Features TIP: If the menu window will not be displayed, try the following procedure. For Windows 7: 1. Click “start” on Windows. 2. Click “All Programs” → “Accessories” → “Run”. 3. Type your CD-ROM drive name (example: “Q:\”) and “LAUNCHER.EXE” in “Name”. (example: Q:\ LAUNCHER.EXE) 4. Click “OK”. the menu window will be displayed. 2 Click “PC Control Utility Pro 4” on the menu window. The installation will start.
3. Convenient Features Step 2: Connect the projector to a LAN. Connect the projector to the LAN by following the instructions in “Connecting to a Wired LAN” (→ page 123), “Connecting to a Wireless LAN (Optional: NP02LM series)” (→ page 124) and “9. Controlling the Projector by Using an HTTP Browser” (→ page 45) Step 3: Start PC Control Utility Pro 4 Click “Start” → “All programs” or “Programs” → “NEC Projector User Supportware” → “PC Control Utility Pro 4” → “PC Control Utility Pro 4”.
3. Convenient Features Using on Mac OS Step 1: Install PC Control Utility Pro 5 on the computer 1. Insert the accompanying NEC Projector CD-ROM in your Mac CD-ROM drive. The CD-ROM icon will be displayed on the desktop. 2. Double-click the CD-ROM icon. The CD-ROM window will be displayed. 3. Double-click the “Mac OS X” folder. 4. Double-click “PC Control Utility.mpkg”. The installer will start. 5. Click “Next”. “END USER LICENSE AGREEMENT” screen will be displayed. 6.
3. Convenient Features ⓫ Projecting Your Computer’s Screen Image from the Projector over a LAN (Image Express Utility Lite) Using Image Express Utility Lite contained on the supplied NEC Projector CD-ROM allows you to send the computer’s screen image and sound to the projector over a USB cable or a wired or wireless LAN. Image Express Utility Lite is a program compatible with Windows. Image Express Utility Lite for Mac OS is a program compatible with Mac OS.
3. Convenient Features Using on Windows Step 1: install Image Express Utility Lite on the computer. NOTE: • To install or uninstall the program, the Windows user account must have “Administrator” privilege (Windows 8, Windows 7, Windows Vista and Windows XP). • Exit all running programs before installation. If another program is running, the installation may not be completed. • Image Express Utility Lite will be installed to the system drive of your computer.
3. Convenient Features Step 3: Start Image Express Utility Lite. 1. On Windows, click “Start” → “All programs” → “NEC Projector UserSupportware” → “Image Express Utility Lite” → “Image Express Utility Lite”. Image Express Utility Lite will start. The select window for network connection will be displayed 2. Select Network and click “OK”. The select window for destination will show a list of connectable projectors.
3. Convenient Features Starting Image Express Utility Lite from a USB Memory or SD Card Image Express Utility Lite can be started from commercially available removable media such USB memory or SD cards if it is copied beforehand. This will eliminate the trouble of installing Image Express Utility Lite to your computer. 1. Copy Image Express Utility Lite to removable media. Copy all the folders and files (total size approx.
3. Convenient Features Downloading Image Express Utility Lite via the HTTP server Downloading procedure when the projector is connected to the Internet. 1. Access the HTTP server. (→ page 45) 2. Select the “NETWORK SETTINGS” tab and then the “NETWORK SERVICE” tab. 3. Click “DOWNLOAD” for “Image Express Utility Lite”. The download page will be displayed. 4. Place a checkmark for IEU_Lite (removable-media).zip and/or gct.ngm. 5. Click “DOWNLOAD”. 6.
3. Convenient Features Using on Mac OS Step 1: Install Image Express Utility Lite for Mac OS on the computer 1. Insert the accompanying NEC Projector CD-ROM in your Mac CD-ROM drive. The CD-ROM icon will be displayed on the desktop. 2. Double-click the CD-ROM icon. The CD-ROM window will be displayed. 3. Double-click the “Mac OS X” folder. 4. Double-click “Image Express Utility Lite.dmg”. The “Image Express Utility Lite” window will be displayed. 5.
3. Convenient Features TIP: Viewing the Help of Image Express Utility Lite for Mac OS • From the menu bar, click “Help” → “Image Express Utility Lite Help” while Image Express Utility is running.
3. Convenient Features ⓬ Projecting an Image from an Angle (Geometric Correction Tool in Image Express Utility Lite) The Geometric Correction Tool (GCT) function allows you to correct distortion of images projected even from an angle. What you can do with GCT • The GCT feature includes the following three functions • 4-point Correction: You can fit a projected image within the border of the screen easily by align the four corners of an image to the ones of the screen.
3. Convenient Features 3. Use the mouse to click the [ • ] mark of which corner you wish to move. The currently selected [ • ] mark will turn red. (In the above example, Windows screens are omitted for clarification.) 4. Drag the selected [ • ] mark to the point you wish to correct and drop it. • When you click somewhere within the project image area, the nearest [ • ] mark will go to the position where the mouse cursor is. 5. Repeat Step 3 and 4 to correct the distortion of the projected image.
3. Convenient Features ⓭ Viewing 3D Images The projector provides 3D images to a user wearing commercially available LCD shutter eyeglasses. CAUTION Health precautions Before viewing, be sure to read health care precautions that may be found in the user’s manual included with your LCD shutter eyeglasses or your 3D compatible content such as DVDs, video games, computer’s video files and the like.
3. Convenient Features On-screen menu for 3D images Follow the steps to display the 3D menu. 1. Press the MENU button. The on-screen menu will be displayed. 2. Press the ▷ button twice. The [SETUP] menu will be displayed. 3. Press the ▽ button once, and then press the ▷ button five times. The [3D] menu will be displayed 4. Press the ▽ button to select a signal and press the ENTER button. The 3D (DETAIL SETTINGS) screen will be displayed. 5.
3. Convenient Features 8. Press the ▽ button to select a compatible eyeglass method and press the ENTER button. Set other 3D-related menu options such as [FORMAT] and [L/R INVERT] as necessary. 9. Press the MENU button once. The menu will disappear. Selecting input connected to a source of 3D images [COMPUTER/HDMI1/HDMI2/VIDEO] This function switches the 3D mode between ON and OFF for each input.
3. Convenient Features Troubleshooting on viewing 3D images If images will not be displayed in 3D or 3D images appear as 2D, check the following table. Also refer to the user’s manual accompanied with your 3D content or LCD shutter eyeglasses. Possible causes • The content you are playing back is not compatible with 3D. • • • • Solutions • Play back a content compatible with 3D. • Use the projector’s menu to turn on 3D mode for the selected The 3D mode was turned off for the selected source.
3. Convenient Features ⓮ Connecting Your Microphone Connecting a commercially available dynamic or condenser microphone to the MIC input jack allows you to output your mic sound from the built-in speaker. Sound from COMPUTER, HDMI 1, HDMI 2, and VIDEO audio inputs or sound of USB-A/LAN input will be heard from the speaker with your microphone voice. Type of microphone can be selected. From the menu, select [SETUP] → [INSTALLATION] → [MIC SELECT] (→ page 99) Microphone sensitivity can be adjusted.
4. Using the Viewer ❶ What you can do with the Viewer The Viewer has the following features. • When a commercially available USB memory that stores image files is inserted into the USB port (Type A) of the projector, the Viewer allows you to view the image files on the USB memory. Even if no computer is available, presentations can be conducted simply with the projector. • Supported graphic format is JPEG.
4. Using the Viewer NOTE • The USB port of the projector does not support USB hub. • The following operations by using the buttons on the projector are not possible when the VIEWER screen such as the slide screen and the thumbnail screen is displayed. - Keystone correction by using the ▲/▼ button - Auto Adjustment by using the AUTO ADJ.
4. Using the Viewer ❷ Projecting images stored in a USB memory device This section explains the basic operation of the Viewer. The explanation provides the operational procedure when the Viewer toolbar (→ page 76) is set to the factory default. • Starting the Viewer........................................................................below • Removing the USB memory from the projector........................ page 74 • Exiting the Viewer.....................................................................
4. Using the Viewer 4. Press the ENTER button. The thumbnail screen will be displayed. (→ page 75) 5. Use the ▲▼◀ or ▶ button to select an icon. • The → (arrow) symbol on the right indicates there are more pages. pressing the PAGE ▽ (page down) button will show the next page: pressing the PAGE △ (page up) will show the previous page. 6. Press the ENTER button. The selected slide will be displayed. • When a folder icon is selected, icons contained in the folder will be displayed. 7.
4. Using the Viewer Removing the USB memory from the projector 1. Select the VIEWER start screen. Press the EXIT button with no menu displayed. 2. Remove the USB memory from the projector. Make sure that the LED on the USB memory is not flashing before removing the USB memory. NOTE: If you remove the USB memory from the projector with a slide displayed, the projector may not operate correctly. If this happens, turn off the projector and unplug the power cord.
4. Using the Viewer Parts of each screen The Viewer has four screens. (1) Viewer start screen (5) (2) (3) Thumbnail screen (6) (4) (7) (9) Slide screen/ (11) Slideshow screen (8) (10) (12) Name Description (1) Viewer start screen This screen will be displayed first when you select the Viewer. (2) USB icon This icon indicates that the USB memory is inserted into the projector. (3) Thumbnail screen This screen will show a list of folders and image files stored in the USB memory.
4. Using the Viewer Using the toolbar 1. Press the MENU button. The toolbar will be displayed. The SOURCE screen will be displayed as Viewer connection screen. 2. Use the ◀ or ▶ button to select an item and use the ▲ or ▼ button to select its available option. When the cursor is placed, the selected item will be changed to yellow. The ▲ or ▼ shows more available choices. 3. Press the ENTER button. The selected item will be displayed. 4. Press the MENU button two times.
4. Using the Viewer Slide toolbar (1) Menu Options (1) Display (2) (3) (4) Description Closes the menu and switches to the slide screen. Closes the menu and displays the thumbnail screen. Closes the menu and starts the slideshow from the highlighted item. (2) Image display Closes the menu and displays the image in its actual size. Closes the menu and displays the image in the projector’s maximum resolution.
5. Using On-Screen Menu ❶ Using the Menus NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected. 1. Press the MENU button on the remote control or the projector cabinet to display the menu. NOTE: The commands such as ENTER, EXIT, ▲▼, ◀▶ in the bottom show available buttons for your operation. 2. Press the ◀▶ buttons on the remote control or the projector cabinet to display the submenu. 3.
5. Using On-Screen Menu ❷ Menu Elements Tab Slide bar Solid triangle Available buttons Source Highlight Radio button Wireless symbol ECO mode symbol High Altitude symbol Off Timer remaining time Thermometer symbol Key Lock symbol Menu windows or dialog boxes typically have the following elements: Highlight �����������������������������Indicates the selected menu or item. Solid triangle ����������������������Indicates further choices are available.
5. Using On-Screen Menu ❸ List of Menu Items Some menu items are not available depending on the input source. Menu Item Default * COMPUTER SOURCE HDMI1 * HDMI2 * VIDEO * USB-A * LAN * USB-B * * PRESET REFERENCE DETAIL SETTINGS PICTURE ADJUST * GAMMA CORRECTION*1 SCREEN SIZE*2 COLOR TEMPERATURE COLOR ENHANCEMENT DYNAMIC CONTRAST Options 1–7 HIGH-BRIGHT, PRESENTATION, VIDEO, MOVIE, GRAPHIC, sRGB, DICOM SIM.
5.
5. Using On-Screen Menu Menu Item Default LAMP LIFE REMAINING USAGE TIME LAMP HOURS USED TOTAL CARBON SAVINGS TOTAL COST SAVINGS RESOLUTION HORIZONTAL FREQUENCY SOURCE(1) VERTICAL FREQUENCY SYNC TYPE SYNC POLARITY SCAN TYPE SIGNAL TYPE VIDEO TYPE SOURCE(2) BIT DEPTH VIDEO LEVEL 3D SIGNAL IP ADDRESS WIRED LAN INFO.
5. Using On-Screen Menu ❹ Menu Descriptions & Functions [SOURCE] COMPUTER Selects the computer connected to your COMPUTER input connector signal. NOTE: When the component input signal is connected to the COMPUTER IN connector, select [COMPUTER] respectively. HDMI1 and 2 Selects the HDMI compatible equipment connected to your HDMI 1 or HDMI 2 IN connector. VIDEO Selects what is connected to your VIDEO input-VCR, DVD player or document camera.
5. Using On-Screen Menu ❺ Menu Descriptions & Functions [ADJUST] [PICTURE] [PRESET] This function allows you to select optimized settings for your projected image. You can adjust neutral tint for yellow, cyan or magenta. There are seven factory presets optimized for various types of images. You can also use [DETAIL SETTINGS] to set user adjustable settings to customize each gamma or color. Your settings can be stored in [PRESET 1] to [PRESET 7].
5. Using On-Screen Menu Storing Your Customized Settings [REFERENCE] This function allows you to store your customized settings in [PRESET 1] to [PRESET 7]. First, select a base preset mode from [REFERENCE], then set [GAMMA CORRECTION], [SCREEN SIZE], [COLOR TEMPERATURE], [COLOR ENHANCEMENT], and [DYNAMIC CONTRAST]. HIGH-BRIGHT �������� Recommended for use in a brightly lit room. PRESENTATION ����� Recommended for making a presentation using a PowerPoint file.
5. Using On-Screen Menu [CONTRAST] Adjusts the intensity of the image according to the incoming signal. [BRIGHTNESS] Adjusts the brightness level or the back raster intensity. [SHARPNESS] Controls the detail of the image. [COLOR] Increases or decreases the color saturation level. [HUE] Varies the color level from +/− green to +/− blue. The red level is used as reference.
5. Using On-Screen Menu [IMAGE OPTIONS] Adjusting Clock and Phase [CLOCK/PHASE] This allows you to manually adjust CLOCK and PHASE. CLOCK ������������������� Use this item to fine tune the computer image or to remove any vertical banding that might appear. This function adjusts the clock frequencies that eliminate the horizontal banding in the image. This adjustment may be necessary when you connect your computer for the first time.
5. Using On-Screen Menu Adjusting Horizontal/Vertical Position [HORIZONTAL/VERTICAL] Adjusts the image location horizontally and vertically. NOTE: The [HORIZONTAL] and [VERTICAL] items are not available for VIDEO, HDMI1, HDMI2, USB-A, LAN, and USB-B. - An image can be distorted during the adjustment of [CLOCK] and [PHASE]. This is not malfunction. - The adjustments for [CLOCK], [PHASE], [HORIZONTAL], and [VERTICAL] will be stored in memory for the current signal.
5. Using On-Screen Menu Selecting Aspect Ratio [ASPECT RATIO] The term “aspect ratio” refers to the ratio of width to height of a projected image. The projector automatically determines the incoming signal and displays it in its appropriate aspect ratio. • This table shows typical resolutions and aspect ratios that most computers support.
5. Using On-Screen Menu Sample image when the appropriate aspect ratio is automatically determined M332XS [Computer signal] Aspect ratio of incoming signal 4:3 5:4 4:3 Letterbox 16:9 15:9 16:10 Sample image when the appropriate aspect ratio is automatically determined [Video signal] Aspect ratio of incoming signal Sample image when the aspect ratio is automatically determined Squeeze NOTE: To display a squeezed signal properly, select [16:9] or [WIDE ZOOM].
5. Using On-Screen Menu Turning on Noise Reduction [NOISE REDUCTION] This function allows you to select the level of noise reduction. The projector is set to the optimized level for each signal at the factory. Select your preference item for your signal when video noise is noticeable. The options are [OFF], [LOW], [MEDIUM], and [HIGH]. NOTE: This feature is not available for the RGB signal. Noise reduction set to off gives best image quality by way of higher bandwidth.
5. Using On-Screen Menu ❻ Menu Descriptions & Functions [SETUP] [GENERAL] Using Digital Zoom [DIGITAL ZOOM] This feature allows you to electronically fine adjust the image size on the screen. Use the ◀ or ▶ button to large or reduce the projected image. TIP: To adjust the projected image size roughly, move the projector away or closer to the screen. To fine adjust the zoom, use the [DIGITAL ZOOM] function.
5. Using On-Screen Menu Using the Wall Color Correction [WALL COLOR] This function allows for quick adaptive color correction in applications where the screen material is not white. NOTE: • Selecting [WHITEBOARD] reduces lamp brightness. • The [WALL COLOR] item cannot be selected when [ON] is selected for [3D] while images are projected.
5. Using On-Screen Menu ECO OPTION Set the option when [ECO] is selected for [ECO MODE]. CONSTANT BRIGHTNESS: OFF ������������������������ The CONSTANT BRIGHTNESS feature will not work. The lamp brightness will gradually decrease over long periods of time. ON ������������������������� The lamp brightness will increase according to the lamp use of time and will be kept at the lamp brightness equivalent to the brightness at ECO.
5. Using On-Screen Menu [MENU] Selecting Menu Color [COLOR SELECT] You can choose between two options for menu color: COLOR and MONOCHROME. Turning On / Off Source Display [SOURCE DISPLAY] This option turns on or off input name display such as COMPUTER, HDMI1, HDMI2, VIDEO, USB-A, LAN, USB-B, to be displayed on the top right of the screen. When no input signal is present, the no-signal guidance prompting you to check for an available input will be displayed at the center of the screen.
5. Using On-Screen Menu Selecting Menu Display Time [DISPLAY TIME] This option allows you to select how long the projector waits after the last touch of a button to turn off the menu. The preset choices are [MANUAL], [AUTO 5 SEC], [AUTO 15 SEC], and [AUTO 45 SEC]. The [AUTO 45 SEC] is the factory preset. Selecting a Color or Logo for Background [BACKGROUND] Use this feature to display a blue/black screen or logo when no signal is available. The default background is [BLUE].
5. Using On-Screen Menu [INSTALLATION] Selecting Projector Orientation [ORIENTATION] This reorients your image for your type of projection. The options are: desktop front projection, ceiling rear projection, desktop rear projection, and ceiling front projection. DESKTOP FRONT CEILING REAR DESKTOP REAR CEILING FRONT Disabling the Cabinet Buttons [CONTROL PANEL LOCK] This option turns on or off the CONTROL PANEL LOCK function. NOTE: • This CONTROL PANEL LOCK does not affect the remote control functions.
5. Using On-Screen Menu Selecting Communication Speed [COMMUNICATION SPEED] This feature sets the baud rate of the PC Control port (D-Sub 9P). It supports data rates from 4800 to 38400 bps. The default is 38400 bps. Select the appropriate baud rate for your equipment to be connected (depending on the equipment, a lower baud rate may be recommended for long cable runs). NOTE: Your selected communication speed will not be affected even when [RESET] is done from the menu.
5. Using On-Screen Menu Using Test Pattern [TEST PATTERN] Displays the test pattern to check for image distortion at the time of the projector setup. Press the ENTER button to display the test pattern; press the EXIT button to close the test pattern and return to the menu. Menu operation and keystone correction are not possible when the test pattern is displayed. Selecting Microphone Type [MIC SELECT] This feature allows you to select dynamic or condenser type for your microphone.
5. Using On-Screen Menu Selecting Signal Format [COLOR SYSTEM] This feature allows you to select video standards manually. Normally select [AUTO]. Select the video standard from the pulldown menu. Enabling or Disabling WXGA Mode [WXGA MODE] Selecting [ON] will give priority to WXGA (1280 × 768)/WUXGA (1920 × 1080) signals in recognizing an input signal. When [WXGA MODE] is set to [ON], XGA (1024 × 768)/UXGA (1600 × 1200) signals may not be recognized on M332XS. In this case, select [OFF].
5. Using On-Screen Menu [OPTIONS(2)] Selecting Standby condition in [STANDBY MODE] The projector has two standby modes: [NORMAL] and [NETWORK STANDBY]. The [NORMAL] mode is the mode that allows you to put the projector in the power-saving condition which consumes less power than the [NETWORK STANDBY] mode. The projector is preset for the [NORMAL] mode at the factory.
5. Using On-Screen Menu Turning On the Projector By Applying Computer Signal [AUTO POWER ON(COMP.)] When the projector is in Standby mode, applying a computer signal from a computer connected to the COMPUTER IN input will power on the projector and simultaneously project the computer’s image. This functionality eliminates the need to always use the POWER button on the remote control or the projector cabinet to power on the projector.
5. Using On-Screen Menu Setting carbon footprint factor [CARBON CONVERT] Adjusts the carbon footprint factor in the carbon saving calculation. The initial setting is 0.505[kg-CO2/kWh] based on the CO2 Emissions from Fuel Combustion (2008 Edition) published by OECD. Selecting your currency [CURRENCY] Displays electricity pricing (available in 4 currency units).
5. Using On-Screen Menu [3D] Selecting input connected to a source of 3D images [COMPUTER/HDMI1/HDMI2/VIDEO] [3D] This function switches the 3D mode between ON and OFF for each input. ON ������������������������� Turns on the 3D mode for the selected input. NOTE: To confirm that the supported 3D signal is accepted, use either way of the following: • Make sure that [3D] is displayed in the top right of the screen after the source is selected. • Display [INFO.
5. Using On-Screen Menu [L/R INVERT] Change the setting if you have difficulty seeing 3D images. NON-INVERT ��������� Normal setting. INVERT ������������������ Changes the order of displaying the images for left eye and right eye. NOTE: This option is available only when [DLP® Link] is selected for [GLASSES].
5. Using On-Screen Menu Setting up the Projector for a Wired LAN Connection [WIRED LAN] Important • Consult with your network administrator about these settings. • When using a wired LAN connection, connect a LAN cable (Ethernet cable) to the LAN port (RJ-45) of the projector. (→ page 123) TIP: The network settings you make will not be affected even when [RESET] is done from the menu. [WIRED LAN] [SETTINGS] [DISABLE] Wired LAN connection will be turned off.
5. Using On-Screen Menu Setting up the Projector for a Wireless LAN Connection (with the optional USB Wireless LAN Unit equipped) [WIRLESS LAN] Important • Consult with your network administrator about these settings. • When using a wireless LAN connection, attach the optional USB Wireless LAN to the projector.
5. Using On-Screen Menu Hints on How to Set Up LAN Connection To set up the projector for a LAN connection: Access the HTTP server function to display the web browser (→ page 45) and select [NETWORK SETTINGS] → [SETTINGS] → [WIRELESS LAN] → [PROFILE 1] or [PROFILE 2]. Two settings can be set for the USB Wireless LAN Unit. Next select [SETTINGS] for your selected profile, and set [ENABLE] or [DISABLE] for [DHCP], [IP ADDRESS], [SUBNET MASK], and [GATEWAY]. Last click [SAVE].
5. Using On-Screen Menu ❼ Menu Descriptions & Functions [INFO.] Displays the status of the current signal and lamp usage. This item has six pages. The information included is as follows: TIP: Pressing the HELP button on the remote control will show the [INFO.] menu items. [USAGE TIME] [LAMP LIFE REMAINING] (%)* [LAMP HOURS USED] (H) [TOTAL CARBON SAVINGS] (kg-CO2) [TOTAL COST SAVINGS]($) * The progress indicator shows the percentage of remaining bulb life.
5.
5.
5. Using On-Screen Menu [OTHERS] [PROJECTOR NAME] [MODEL NO.
5. Using On-Screen Menu ❽ Menu Descriptions & Functions [RESET] Returning to Factory Default [RESET] The RESET feature allows you to change adjustments and settings to the factory preset for a (all) source (s) except the following: [CURRENT SIGNAL] Resets the adjustments for the current signal to the factory preset levels.
6. Installation and Connections This section describes how to set up your projector and how to connect video and audio sources. Your projector is simple to set up and use. But before you get started, you must first: ① Set up a screen and the projector. 1 ② Connect your computer or video equipment to the projector. (→ page 117, 119, 120, 121, 122, 123) ③ Connect the supplied power cord. (→ page 16) NOTE: Ensure that the power cord and any other cables are disconnected before moving the projector.
6. Installation and Connections [M352WS/M302WS] The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 60" (1.52 m) measured diagonally when the projector is roughly 22 inches (0.6 m) from the wall or screen. The largest the image can be is 150" (3.8 m) when the projector is about 58 inches (1.5 m) from the wall or screen. Screen Size (Unit: cm/inch) 323.1(W)�201.9(H) / 127(W)�79(H) 15 0" 258.5(W)�161.
6. Installation and Connections Throw Distance and Screen Size The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of installation.
6. Installation and Connections ❷ Making Connections NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on the power to the notebook PC. In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up. * If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver or power management software.
6. Installation and Connections • Select the source name for its appropriate input connector after turning on the projector. Input connector SOURCE button on the projector cabinet Button on the remote control COMPUTER IN COMPUTER (COMP1) HDMI 1 IN HDMI1 HDMI1 HDMI 2 IN HDMI2 HDMI2 USB-B USB-B (USB-B) NOTE: The projector is not compatible with video decoded outputs of the NEC ISS-6020 switcher.
6. Installation and Connections Connecting an External Monitor AUDIO OUT MONITOR OUT(COMP.) Computer cable (VGA) (not supplied) Computer cable (VGA) (supplied) Stereo mini-plug audio cable (not supplied) You can connect a separate, external monitor to your projector to simultaneously view on a monitor the computer analog image you’re projecting. NOTE: • Daisy chain connection is not possible. • When audio equipment is connected, the projector speaker is disabled.
6. Installation and Connections Connecting Your DVD Player or Other AV Equipment Connecting Video Input VIDEO IN AUDIO IN Video cable (not supplied) Audio cable (not supplied) Audio equipment Audio cable (not supplied) • Select the source name for its appropriate input connector after turning on the projector. Input connector VIDEO IN SOURCE button on the projector cabinet Button on the remote control (VIDEO) VIDEO NOTE: The AUDIO IN L and R jacks (RCA) are shared between the Video inputs.
6. Installation and Connections Connecting Component Input AUDIO IN Stereo mini plug - to - RCA audio cable (not supplied) COMPUTER IN 15-pin - to - RCA (female) × 3 cable adapter (ADP-CV1E) Audio Equipment Component video RCA × 3 cable (not supplied) DVD player Audio cable (not supplied) • Select the source name for its appropriate input connector after turning on the projector.
6. Installation and Connections Connecting HDMI Input You can connect the HDMI output of your DVD player, hard disk player, Blu-ray player, or notebook type PC to the HDMI IN connector of your projector. NOTE: The HDMI IN connector supports Plug & Play (DDC2B). HDMI 1 IN HDMI 2 IN HDMI cable (not supplied) Use High Speed HDMI® Cable.
6. Installation and Connections Connecting to a Wired LAN The projector comes standard with a LAN port (RJ-45) which provides a LAN connection using a LAN cable. To use a LAN connection, you are required to set the LAN on the projector menu. Select [SETUP] → [WIRED LAN]. (→ page 106). Example of LAN connection Example of wired LAN connection Server Hub LAN cable (not supplied) NOTE: Use a Category 5 or higher LAN cable.
6. Installation and Connections Connecting to a Wireless LAN (Optional: NP02LM series) The USB Wireless LAN Unit also provides a wireless LAN connection. To use a wireless LAN connection, you are required to assign an IP address to the projector. Important: • If you use the projector with the USB Wireless LAN Unit in the area where the use of wireless LAN equipment is prohibited, remove the USB Wireless LAN Unit from the projector. • Buy the appropriate USB Wireless LAN Unit for your country or area.
6. Installation and Connections Prepare a Phillips screw driver beforehand. 1. Press the POWER button to turn off the projector and set it into standby condition, and disconnect the power cord. 2. Remove the USB (LAN) port cover. Loosen the screw securing the port cover. • The screw is not removable. 3. Slowly insert the USB Wireless LAN Unit into the USB (LAN) port. Remove the cap from the USB Wireless LAN Unit, and then insert it with the surface (side of indicator) facing outward.
6. Installation and Connections Example of wireless LAN connection (Network Type → Infrastructure) PC with wireless LAN card inserted PC with built-in wireless LAN function USB Wireless LAN Unit Wireless access point Wired LAN Use the HTTP server function to make the settings. (→ page 45) Example of wireless LAN connection (Network Type → Ad Hoc) USB Wireless LAN Unit PC with wireless LAN card inserted PC with built-in wireless LAN function To enable direct communication (i.e.
7. Maintenance This section describes the simple maintenance procedures you should follow to clean the lens, the cabinet, and to replace the lamp. ❶ Cleaning the Lens • Turn off the projector before cleaning. • The projector has a plastic lens. Use a commercially available plastic lens cleaner. • Do not scratch or mar the lens surface as a plastic lens is easily scratched. • Never use alcohol or glass lens cleaner as doing so will cause damage to the plastic lens surface.
7. Maintenance ❸ Replacing the Lamp When the lamp reaches the end of its life, the LAMP indicator in the cabinet will blink red and the message “THE LAMP HAS REACHED THE END OF ITS USABLE LIFE. PLEASE REPLACE THE LAMP.” will appear (*). Even though the lamp may still be working, replace the lamp to maintain the optimal projector performance. After replacing the lamp, be sure to clear the lamp hour meter.
7. Maintenance To replace the lamp: 1. Remove the lamp cover. (1) Loosen the lamp cover screw • The lamp cover screw is not removable. (2) Push and slide the lamp cover off. 2. Remove the lamp housing. (1) Loosen the three screws securing the lamp housing until the phillips screwdriver goes into a freewheeling condition. • The three screws are not removable. • There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.
7. Maintenance 3. Install a new lamp housing. (1) Insert a new lamp housing until the lamp housing is plugged into the socket. (2) Push the top center of the lamp housing to secure it. (3) Secure it in place with the three screws. • Be sure to tighten the screws. 4. Reattach the lamp cover. (1) Slide the lamp cover back until it snaps into place. (2) Tighten the screw to secure the lamp cover. • Be sure to tighten the screw. This completes the lamp replacement.
8. Appendix ❶ Troubleshooting This section helps you resolve problems you may encounter while setting up or using the projector. Indicator Messages Power Indicator Indicator Condition Off 0.5 sec On, Blinking light Blue 0.5 sec Off 2.5 sec On, 0.5 sec Off Steady light Blue Orange Red Projector Condition The main power is off The projector is getting ready to turn on. – Wait for a moment. Off Timer is enabled. – Note The projector is turned on.
8. Appendix Common Problems & Solutions (→ “Power/Status/Lamp Indicator” on page 131.) Problem Check These Items Does not turn on or shut down • Check that the power cord is plugged in and that the power button on the projector cabinet or the remote control is on. (→ pages 16, 17) • Ensure that the lamp cover is installed correctly. (→ page 130) • Check to see if the projector has overheated.
8. Appendix If there is no picture, or the picture is not displayed correctly. • Power on process for the projector and the PC. Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on the power to the notebook PC. In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up.
8. Appendix ❷ Specifications This section provides technical information about projector’s performance. [M352WS/M302WS/M332XS] Optical Model Number Projection System NP-M352WS Single DLP® chip (0.65", aspect 16:10) Resolution*1 Lens 1280 × 800 pixels (WXGA) Digital zoom and manual focus Digital Zoom Ratio = 1.2 F2.4/ f=6.
8.
8. Appendix ❸ Cabinet Dimensions [M352WS/M302WS/M332XS] 286(11.3) 291 (11.5) Unit: mm (inch) 368 (14.5) 98 (3.9) Lens center 108 (4.3) Lens center 134 (5.3) 80 (3.2) 130 (5.2) 150 (5.9) 200 (7.9) Holes for ceiling mount 175 (6.
8. Appendix Attaching the Optional Cable Cover (NP05CV) An optional cable cover (NP05CV) is available for hiding cables. CAUTION: • Be sure to tighten the screws after attaching the cable cover. Failure to do so may cause the cable cover to come off and fall, resulting in injury or damage to the cable cover. • Do not put bundled cables in the cable cover. Failure to do so may damage the power cord, resulting a fire. • Do not force excessive pressure to the cable cover.
8. Appendix ❹ Pin Assignments of D-Sub COMPUTER Input Connector Mini D-Sub 15 Pin Connector 6 11 12 13 14 15 7 8 9 10 1 2 3 4 5 Signal Level Video signal : 0.7Vp-p (Analog) Sync signal : TTL level Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 RGB Signal (Analog) Red Green or Sync on Green Blue Ground Ground Red Ground Green Ground Blue Ground Hot plug Sync Signal Ground No Connection Bi-directional DATA (SDA) Horizontal Sync or Composite Sync Vertical Sync Data Clock COMPUTER IN NOTE: Pin Nos.
8.
8.
8. Appendix ❼ Troubleshooting Check List Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem more efficiently. * Print this page and the next page for your check.
8. Appendix In the space below please describe your problem in detail. Information on application and environment where your projector is used Projector Installation environment Model number: Screen size: inch Serial No.
8. Appendix ❽ TCO Certification Some models in this product family are TCO certified. All TCO certified models have the TCO mark on the marking plate (on the bottom of the product). To see a list of our TCO certified projectors and their TCO Certification (in English only), visit our website at http://www.nec-display.com/ap/en_projector/tco/index.html The TCO certification, designed by TCO Development, is an international environmental and ergonomics standard for IT equipment.
8. Appendix ❾ REGISTER YOUR PROJECTOR! (for residents in the United States, Canada, and Mexico) Please take time to register your new projector. This will activate your limited parts and labor warranty and InstaCare service program. Visit our web site at www.necdisplay.com, click on support center/register product and submit your completed form online.
© NEC Display Solutions, Ltd.
