Owner Manual

ManualsBrandsneodrain ManualsCore PlumbingGrid Shower Drain

Table Of Contents

80%

Stainless strainer / Hair catcher

Drain body / Channel

Threaded adaptor / Height adjustable

Grate & strainer lifting hook

Leveling feet / 2 PCS

Protective fabric

Please be sure to read carefully before installation.

Three styles of stainless steel grating options available:

Note: Always wipe the Decorative Finish with a soft cloth after each use.

Grating and Parts

Preparation

The substrate should be smooth, level, clean and free of all dirt, oil, laitance, paint, concrete sealers or curing compounds.

Dry dusty concrete slabs or masonry should be dampened and excess water swept off.

The following tools and materials maybe needed: Hole Saw, Crescent Wrench, Level, Utility Knife, Ruler or Tape measure,

Pencil, Notched Trowel, Weep protectors, Silicone, Solvent Cement.

For the traditional type of waterprooﬁng, the professional should build a shower pan in the wet /shower area with PVC, Vinyl, Lead

or Fiberglass material, then the drain usually connect to the waste line with a mechanical clamp down drain ﬂange (drain base), some

model do not include such ﬂange and need separately purchase before installation.

www.neodrain.com

1. Please read this installation instructions carefully before proceeding.

2. Thoroughly inspect the product and components, contact our support team with report any support @neodrain.com to

damaged or missing components for a replacement, return or repair.

3. Consult local building codes to ensure the installation complies with standards in your area. The warranty will be void if

the product is installed with a conspicuous defect.

4.We recommend a ﬂow rate no greater than 12 GPM for use with this product.

5. The information provided in this instruction are general guidelines and a licenced professional should always be used

during installation.

( *12" do not use leveling feet.)

Summary of content (4 pages)

PAGE 1
80% 1. Please read this installation instructions carefully before proceeding. 2. Thoroughly inspect the product and components, contact our support team with support @neodrain.com to report any damaged or missing components for a replacement, return or repair. 3. Consult local building codes to ensure the installation complies with standards in your area. The warranty will be void if the product is installed with a conspicuous defect. 4.
PAGE 2
Site & Placement Whether for a renovation or new construction, choosing the drain location is contingent on the waste line location, which may be predetermined or already installed. Moving a waste line may bepossible, depending on site conditions. Tile insert process If you don't buy Tile-insert design, just skip to next page. If you choose 2 in 1 grate, the tray also can be used as stainless grate besides as tile tray, the regular tile-insert grate is unavailable in this way.
PAGE 3
Installation The following installation details do not cover every possible situation, some may not be appropriate for DIY. Always consult with licenced professional during installation. MORTAR Slope 4 3 2 slo 1° pe 7 6 8 Dustcloth SUB FLOOR 10 SUB FLOOR Side View 2 Installation Step: 1. Coupling the drain base outlet to 2" or 3" schedule 40 DWV pipe using correct solvent cement. 2. Block the drain opening with rag.
PAGE 4
Installation Diagram Install with drain base Silicone or grout Tile or stone material Grate Rubber gasket / Threaded coupling Tile adhesive or thinset Clamping plate Sloped mortar bed 2 Pea gravel or tile spacer Waterproof membrane Building paper Sloped mortar bed 1 Outlet Ply wood PVC/ABS drain base /sub drain (Not include, purchase separately.) Concrete/Masonry/XPS board/ Cement mortar bed 2" drainage pipe Drain base assembly (Not include, purchase separately) 2" OD outlet 1.