Installation Guide for Fiber Tap HD8 800-0153-001 Doc. PUBTP800800XU Rev.
Fiber Tap HD8 Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Key Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 About This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fiber Tap HD8 PLEASE READ THESE LEGAL NOTICES CAREFULLY. By using a Net Optics Tap you agree to the terms and conditions of usage set forth by Net Optics, Inc. No licenses, express or implied, are granted with respect to any of the technology described in this manual. Net Optics retains all intellectual property rights associated with the technology described in this manual. This manual is intended to assist with installing Net Optics products into your network.
Fiber Tap HD8 Introduction Get total traffic visibility for monitoring and security devices by placing Net Optics Fiber Tap HD8 on critical network links. The all-optical design of the Fiber Tap HD8 is optimized and tested for high-performance on fiber networks. Available for both singlemode and multimode fiber, the GigaBit and 10 GigaBit Fiber Tap HD8 supports passive monitoring of fiber optics links. Slim Profile Flat-out, the thinnest 8 station Fiber Tap HD8.
Fiber Tap HD8 Key Features Passive, Secure Technology • Provides passive access without data stream interference or introducing a point of failure • All-optical design is optimized and tested for fiber networks • Permanent in-line installation without affecting network performance • Passes all full-duplex traffic (including errors) from all layers for comprehensive troubleshooting • No IP address is needed for the Tap or monitoring device, enhancing monitoring security • Completely transparent to th
Fiber Tap HD8 About This Guide Please read the guide before attempting to install Fiber Tap HD8.
Fiber Tap HD8 Product Diagram Network Port Segments A B A B OUT OUT A B A B OUT OUT A B A B OUT OUT A B A B OUT OUT A B A B OUT OUT A B A B OUT OUT A B A B OUT OUT A B A B OUT OUT Splitter Tap HD 1 www.netoptics.
Fiber Tap HD8 Connecting to the Network 1. Connect Network Port A to the appropriate network device using a Duplex LC cable. 2. Connect Network Port B to the appropriate network device using a Duplex LC cable. 3. Verify that the Tap Network Ports are cabled in-line between two devices. 4. Repeat steps 1-3 as needed for remaining segements. Note:_________________________________________________________________ The use of Singlemode (8.5µm) or Multimode (50µm or 62.
Fiber Tap HD8 Connecting to the Monitoring Device 1. Connect to the Monitor Port using a Net Optics custom LC analyzer cable 2. Connect one side of the twin-duplex fiber cable into a RX port on the monitoring device to view one side of the full-duplex link. 3. Connect the other side of the twin-duplex fiber cable into another RX port on the monitoring device to view the other side of the full-duplex link. 4. Verify that the Tap Monitor Port is cabled to the monitoring device. 5.
Fiber Tap HD8 Specifications Splitter Specifications Fiber Type 10 Gigabit model: Corning Multimode 50 or 62.5/125µm, wavelength 850nm Split Ratio 50/50 70/30 Network Port Insertion Loss Monitor Port Insertion Loss ≤ 4.5 dB ≤ 4.5 dB ≤ 2.4 dB ≤ 6.3 dB Fiber Type 10 Gigabit model: Corning Singlemode 8.5/125µm, wavelength 1310nm or 1550nm Split Ratio 50/50 70/30 Network Port Insertion Loss Monitor Port Insertion Loss ≤ 3.7 dB ≤ 3.7 dB ≤ 2.0 dB ≤ 6.
Fiber Tap HD8 Limitations on Warranty and Liability Net Optics offers a limited warranty for all its products. IN NO EVENT SHALL NET OPTICS, INC. BE LIABLE FOR ANY DAMAGES INCURRED BY THE USE OF THE PRODUCTS (INCLUDING BOTH HARDWARE AND SOFTWARE) DESCRIBED IN THIS MANUAL, OR BY ANY DEFECT OR INACCURACY IN THIS MANUAL ITSELF.
Fiber Tap HD8 Notes: 9
Fiber Tap HD8 Notes: 10
www.netoptics.com © 2010 by Net Optics, Inc. All Rights Reserved.
