Installation Guide

G
H
D
Pergola Additional Materials List
Hardware (in plastic bag)
NOTE: WE HAVE INCLUDED 10% EXTRA SCREWS
BEYOND WHAT IS IDENTIFIED BELOW.
All Screws Included with this Kit are Self-Auguring.
A
. Vinyl Weld Glue (3) - 20000 White
B. 5/8” Self-Auguring Stainless Steel Screws (12) (To lock rafter brackets to the rafters ) - 20016 White
C. 5/8“ Self-Auguring Stainless Steel Screws (36) (To lock rafter hangers to the rafters) - 20016 White
D. 2 1/2” Self-Auguring Stainless Steel Screws (81) (To lock the shade slats to the rafters) - 20007 White
E. 1 1/2” Self-Auguring Stainless Steel Screws (52) (Joiner screws) - 20005 White
F. 1 1/2” Self-Auguring Stainless Steel Screws (48) (Rafter hanger & Rafter Brackets screws) - 20005 White
G. 2 1/2” Self-Auguring Stainless Steel Screws (24) (To lock vinyl column and wood post together at the bottom of each post and above trim cap)
20007 White
H. 4“ Self-Auguring Stainless Steel Screws (48) (To mount the column tops to the beams)
20006 White
Extra Materials You will Need
(Purchase separately from www.edenarbors.com or retailer of our products)
If Mounting Pergola on Concrete (not intended to be installed on concrete
pavers, patio stones, or interlocking bricks) or Wood Deck
I. 4x4x7 Pressure-Treated Wood Posts (3) (purchase at local building center)
K . 4x4 Bolt Down Bracket Kit (purchase from www.newenglandarbors.com or
a retailer of our products)
Refer to bolt down bracket instructions for hardware requirements,
as they pertain to your application:
If mounting pergola onto an existing concrete surface:
• 1/2“ x 3 1/2” x 12“ Wood Shims (24) - Can Be Cut from 1/2” Sheet of Plywood
• 1/4” x 2 3/4“ Cement Screws - Countersunk Head (9)
• 3/16” Concrete drill bit. Minimum 3“ long (1)
If mounting pergola onto a wooden/composite deck with
AN ACCESSIBLE UNDERSIDE:
• 1/2“ x 3 1/2” x 12“ Wood Shims (24) - Can Be Cut from 1/2” Sheet of Plywood
• 1/4” x ?“ Bolts and Nuts - Countersunk Head (9) (Length depends on
blocking material)
• 1/4” Washers (9)
• 1/4” Wood drill bit. Minimum 3“ long (1)
If Mounting Pergola in Ground
J. 4x4x10 Pressure-Treated Wood Posts (3) (purchase at local building center)
L. Concrete Ready Mix (3) (purchase at local building center)
Rafter / Beam Support (Required)
M. 2x6x16 Pressure-Treated Boards (3) (purchase at local building center)
N. 2x6x12 Pressure-Treated Boards (9) (purchase at local building center)
O. 3/8“ x 3 1/2” Lag Screws with Washer s (8) (purchase at local building center)
P. 3/8“ x 3 1/2” Lag Screws (for wood wall) or Anchor Screws (for brick
or concrete wall) (11) (purchase at local building center, also purchase drill bit)*
*) Please consult your local building center for mounting anchors. These second set of
screws will be used to mount your wood beam / ledger onto your structure. Refer to
page 12 for more information.
L
CONCRETE - Ready Mix
Not to Scale
6
12 x 16 Flat Top Pergola
Purchase Separately
Purchase Separately
K
O
Purchase
Separately
E F
CBA
Purchase
Separately
I
Purchase
Separately
J
Purchase
Separately
M
Purchase
Separately
N