32”2 Door Aluminum 65200 33” Insert Grill Aluminum 65204 32” Bar Cart 65207 32” 3 Drawer Aluminum 32” Sink Aluminum 65202 65201 45 Degree Aluminum Set 65205 32” Bar Aluminum 65203 90 Degree Shelf Aluminum 65206 64” Prep Table 65208 OUTDOOR KITCHEN Aluminum Sets Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.
Limited Warranty: All products must be installed, operated, and maintained in accordance with the instructions included with the products. If a product is properly installed, operated, and maintained fails to meet the below limited warranty, NewAge Products, Inc (“NewAge”) will replace the defective product or parts.
OUTDOOR KITCHEN 32”2 Door Aluminum Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65200-INSTL-01-Rev.
Weight Capacity Worktops 32" Worktop. Fits over 1 Cabinet 200 lbs. 56 " Worktop. Fits over 1 Cabinet & Fridge nook. 115 lbs. 115 lbs. 200 lbs. 32" - 2 Door Cabinet Max 630 lbs. 64" Worktop. Fits over 2 Cabinets 88" Worktop. Fits over 2 Cabinets & Fridge nook. 96" Worktop.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
OTHER NOTES TO CONSUMER: Discoloration due to the high heat, for example beside a grill, is a trait of stainless steel and is not covered. Surface rust resulting from acid rain or environmental chemicals are not covered. (Please see maintenance information to combat surface rust). NewAge outdoor powder coated finishes are designed to withstand weathering and are UV stable.
Installing the Legs Parts Needed. 4 X Adjustable Feet 2 1 Open cabinet, remove any shelves or loose items. 3 Align leg with rivet nuts on crossbeam. Tighten in Hex bolts . 16 X Hex Washer Bolt Flip cabinet upside down, locate holes on crossbeam. 3 1 4 Repeat step 3 for each corner. 5 4 2 Stand cabinet upright. To level and adjust legs go to next step.
Levelling the Legs Parts Needed. 1 Use wrench to level cabinet and adjust height. 1 X Glide Wrench 2 Rotate wrench to lower or raise corner of cabinet. 3 Repeat step 1-3 for each corner. 4 Level Cabinet.
Installing the Casters(optional) Parts Needed. 4 X Casters 2 1 Open cabinet, remove any shelves or loose items. 3 Align caster with holes on crossbeam. Tighten in Hex bolts . 16 X Hex Washer Bolt Flip cabinet upside down on protected surface and locate holes on crossbeam. 3 4 1 2 4 Repeat step 3 to install all casters 5 Stand cabinet upright.
Fastening Cabinets(to each other) 1 4 X Hex Nut(M5) 3 2 Parts Needed. Remove plastic caps from cabinets. 4 X Hex Bolt (M5 x 50mm”) X8 Align bolts, tighten lightly. X4 4 Level cabinets and tighten all bolts.
Mounting the Worktop 1 Stand cabinet upright. 2 Place worktop over cabinets. 3 Insert the worktop bolt heads into the keyhole shape slots. 4 Push worktop in to lock. Tighten screws to secure cabinets. Optional: Repeat steps 2-5 for mounting larger worktops.
Inserting Cabinet Shelves 1 Open cabinet doors. Attach shelf clips to desired height. 2 Begin with shelf being level. 3 Insert and position above shelf clips. 4 Lower shelf down onto shelf clips. 5 Install remaining shelves.
Adjusting The Door Hinges Using a Philips screwdriver, the doors can be adjusted: Left, right, forwards and backwards. 1 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise. A 2 To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise.
OUTDOOR KITCHEN 32”2 Sink Base Alum Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65201-INSTL-01-Rev.
Weight Capacity Worktops 32" Worktop. Fits over 1 Cabinet 200 lbs. 56 " Worktop. Fits over 1 Cabinet & Fridge nook. 75 lbs. 64" Worktop. Fits over 2 Cabinets 100 lbs. 32" - Sink Cabinet Max 375 lbs. 88" Worktop. Fits over 2 Cabinets & Fridge nook. 96" Worktop.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
OTHER NOTES TO CONSUMER: Discoloration due to the high heat, for example beside a grill, is a trait of stainless steel and is not covered. Surface rust resulting from acid rain or environmental chemicals are not covered. (Please see maintenance information to combat surface rust). NewAge outdoor powder coated finishes are designed to withstand weathering and are UV stable.
Plumbing Installation Locate the 3 pre slotted holes in the back of the cabinet. Using tin snips cut small webs to release the knockouts. Back View of Sink Cabinet. 1 Locate the 3 pre slotted holes in the bottom of the cabinet. Using tin snips cut small webs to release the knockouts. 2 3 Bottom View of Sink Cabinet. Connect the drain trap adapter to a p-trap and drainage tubing.
Tip-over Hazard Only open one drawer at a time. If this Cabinet is installed on its own please fasten to a permanent structure. OUTDOOR KITCHEN 32"-3 Drawer Cabinet Alum Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65202-INSTL-01-Rev.
Weight Capacity Worktops 200 lbs. 56” Worktop. Fits over 1 Cabinet & Fridge nook. 75 lbs. 75 lbs. 75 lbs. 32” - 3 Drawer Cabinet Max 425 lbs. 64” Worktop. Fits over 2 Cabinets 88” Worktop. Fits over 2 Cabinets & Fridge nook. 96” Worktop.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
OTHER NOTES TO CONSUMER: Discoloration due to the high heat, for example beside a grill, is a trait of stainless steel and is not covered. Surface rust resulting from acid rain or environmental chemicals are not covered. (Please see maintenance information to combat surface rust). NewAge outdoor powder coated finishes are designed to withstand weathering and are UV stable.
Installing the Drawers Removing Drawers. Right Side Left Side Slide Out Inserting Drawers.
OUTDOOR KITCHEN 32"Bar Aluminum Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65203-INSTL-01-Rev.
Weight Capacity Worktops 32" Worktop. Fits over 1 Cabinet 200 lbs. 56 " Worktop. Fits over 1 Cabinet & Fridge nook. 75 lbs. 64" Worktop. Fits over 2 Cabinets 75 lbs. 88" Worktop. Fits over 2 Cabinets & Fridge nook. 32" - SS Bar Cabinet Max 350 lbs. 96" Worktop.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
OTHER NOTES TO CONSUMER: Discoloration due to the high heat, for example beside a grill, is a trait of stainless steel and is not covered. Surface rust resulting from acid rain or environmental chemicals are not covered. (Please see maintenance information to combat surface rust). NewAge outdoor powder coated finishes are designed to withstand weathering and are UV stable.
Installing the Drawer Inserting Drawer. Align Rails Slide In Removing Drawers.
Wine Rack, Ice Tray and Garbage Bin Installation 1 Open Doors. Set rack clips in the desired slot locations on the upright posts. 2 Set rack on top of 4 clips at the same level height. Store beverage bottles. 3 Remove and install beverage chilling tray with formed metal edge. 4 Slide beverage chilling tray into/out of pullout frame. Push in frame to dock. 3 5 Remove and install Garbage bins 5 6 Slide Garbage bins into/out of pullout frame. Push in frame to dock.
OUTDOOR KITCHEN 33"BBQ Cabinet Aluminum Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65204-INSTL-01-Rev.
Weight Capacity 200 lbs. BBQ 115 lbs. 200 lbs. 33” - BBQ Aluminum Max 515 lbs.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
OTHER NOTES TO CONSUMER: Discoloration due to the high heat, for example beside a grill, is a trait of stainless steel and is not covered. Surface rust resulting from acid rain or environmental chemicals are not covered. (Please see maintenance information to combat surface rust). NewAge outdoor powder coated finishes are designed to withstand weathering and are UV stable.
Installing the Casters Parts Needed. 4 X Casters 2 1 Open cabinet, remove any shelves or loose items. 3 Align caster with holes on crossbeam. Tighten in Hex bolts . 16 X Hex Washer Bolt Flip cabinet upside down on protected surface and locate holes on crossbeam. 3 4 1 2 4 Repeat step 3 to install all casters 5 Stand cabinet upright.
Installing the BBQ 1 You may or may not need the adapter brackets depending on the model BBQ you choose 2 Place BBQ so that the rails touch the Brackets 3 Once the BBQ is centered on the Cart lift up edges of BBQ and Dab a little silicone on the rails to hold it in place 4 Place the propane tank in the ring of the tank tray. Rotate tank until bottom slot aligns with wingnut bolt. 5 Turn Wing nut bolt until it is seated in tank slot at bottom of tank. Parts Needed.
*Rear View Shown OUTDOOR KITCHEN 45˚ Cabinet Alum Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65205-INSTL-01-Rev.
Weight Capacity 100 lbs. 50 lbs. 50 lbs. 100 lbs. 45˚ Cabinet Max 300 lbs.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
OTHER NOTES TO CONSUMER: Discoloration due to the high heat, for example beside a grill, is a trait of stainless steel and is not covered. Surface rust resulting from acid rain or environmental chemicals are not covered. (Please see maintenance information to combat surface rust). NewAge outdoor powder coated finishes are designed to withstand weathering and are UV stable.
Installing the Legs Parts Needed. 3 X Adjustable Legs 2 4 6 1 Flip cabinet upside down, locate holes on crossbeam. 3 Repeat step 2 for each leg. 12 x Hex Washer Bolt Align Leg with holes on crossbeam. Tighten 4 Hex bolts with washer and lock washer. Stand cabinet upright. To level and adjust Legs go to next step.
Fastening Cabinets 1 4 X Hex (M5) 3 2 Parts Needed. Remove plastic caps from cabinets. 4 X Hex Bolt (M5 x 50 mm) X8 Align bolts, tighten lightly. X4 4 8 Level cabinets and tighten all bolts.
OUTDOOR KITCHEN 90˚ Corner Shelf Aluminum Warning: Excessive weight hazard! Use two or more people to move, assemble or install shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65206-INSTL-01-Rev.
Weight Capacity 50 lbs. 50 lbs. 100 lbs. 90° Corner Shelf Max 200 lbs.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
OTHER NOTES TO CONSUMER: Discoloration due to the high heat, for example beside a grill, is a trait of stainless steel and is not covered. Surface rust resulting from acid rain or environmental chemicals are not covered. (Please see maintenance information to combat surface rust). NewAge outdoor powder coated finishes are designed to withstand weathering and are UV stable.
Frame Assembly Parts Needed. Hex Washer Bolt (M6 x 25mm) 2 1 Pan Head Bolt (30 x 8/32 x 3/8”) Attach Top to bottom shelf with back pan 4 8/32” x 3/8”pan head bolts. 3 4 On protected surface, attach 2 legs to leg channel with 8 x M6 x25mm hex bolts. Attach shelf using 4X 8/32” x 3/8” Pan Head Bolts. 5 Attach 2 uprights to top shelf and Base assembly using 4 x 8/32” x 3/8” pan head bolts Repeat step 4 for 2 more vertical supports.
Frame Assembly for Granite Top Parts Needed. 1 Undo Stainless Steel Top by removing 6 x Pan head 8/32” x 3/8” bolts 3 Attach Granite corner top with 6 x #6 x 5/8” Pan Head wood screws into Outdoor plywood granite backer. Pan Head Bolt (30 x 8/32 x 3/8”) Pan Head Screw (#6 x 5/8” wood screws) 2 4 Attach 2 included Granite rails using 4 x 8/32” x 3/8” pan head bolts at top of supports. Add silicone using 8 small dabs to hold top in place. Wipe up any extra silicone that seeps out during installation.
Fastening Cabinets 1 2 Parts Needed. Locate bolt slots on upright supports. 4 X Hex Nut (M5) 4 X Flat Washers (M5) X8 4 X Hex Bolt (M5 x 50mm) 3 Align hole locations , put bolt and washer through holes tighten nut lightly. 4 Level cabinets and tighten all bolts.
OUTDOOR KITCHEN 32" Bar Cart SS Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65007-INSTL-01-Rev.
Weight Capacity 50 lbs. 30 lbs. 50 lbs. 100 lbs. Bar Cart Max 230 lbs.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Casters Parts Needed. 4 X Casters 2 4 Flip cart upside down, locate holes on corner brackets. 3 Repeat step 2 for each corner. 16 X Hex Washer Bolt Align foot with holes on crossbeam. Screw in Hex bolts with washer and lock washer. Stand cart upright.
Installing the Drawers Inserting Drawers. Align Rails Slide In Removing Drawers.
Installing the Push Bar, Ice Tray, Liquor Rail 1 Parts Needed. Push handle should be attached by two locations 2 1 Ice Tray Push Bar 2X Pan Head 8mm Bolts 2 Tighten 2 x 8mm x 60mm bolts. In locations shown here. 3 4 Add Ice tray using handles to drop into to cutout in cart top 5 Add Liquor Rail by aligning bolt heads with keyhole slots in tray.
OUTDOOR KITCHEN 64"Prep Table SS Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65008-INSTL-01-Rev.
Weight Capacity 200 lbs. 64" - PREP TABLE Max 200 lbs.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
OTHER NOTES TO CONSUMER: Discoloration due to the high heat, for example beside a grill, is a trait of stainless steel and is not covered. Surface rust resulting from acid rain or environmental chemicals are not covered. (Please see maintenance information to combat surface rust). NewAge outdoor powder coated finishes are designed to withstand weathering and are UV stable.
Table Assembly Parts Needed. 1 Insert Leg Frame into cross rails. Using M6 bolts to fasten the leg frame to cross rails.
Table to Cabinet Ganging Parts Needed. 4 x Hex Bolt (M6x 30) 1 Align inserts in Table Leg Frame with with 4 Holes in side of Cabinet. Fasten 4 x 4mm x 40 mm Hex Bolts as shown. Note: Table has rivet nuts in legs to thread into. Insert bolt from cabinet side.
Table to Table Ganging Parts Needed. 4 X Pan Head Bolts (M4 x 13mm) 1 4 x Ganging Brackets Washers (M4) 2 Using 4 Ganging Brackets and 2 x M4 Pan Head bolts per each bracket. Attach two tables together. 3 Position Brackets over existing bolt heads using clearance holes. 8 On a Flat Protected Surface flip over two tables and align them right to left sides as shown.