User Manual

10 11
ninjakitchen.com
PROGRAMMING DELAY BREW
NOTE: The unit must remain on for the
Delay Brew function to work. DO NOT
power o after setting Delay Brew.
1 Turn the unit on by pressing the
Power button.
2 After filling the water reservoir and
adding ground coee to the brew
basket, be sure the reservoir and brew
basket are securely in place. Place the
empty carafe under the brew basket.
3 Press DELAY BREW. The clock will
flash “12:00”. Use the hour (H) and
minute (M) buttons to set the time
you would like the Delay Brew to begin.
The AM or PM indicator will illuminate
on the left side of the display as you
are setting the time.
4 Select the brew style and that selection
will illuminate. If brewing fewer than
4 cups, press SMALL BATCH, too.
5 Once you have set the time and brew
style, press DELAY BREW to activate, or
wait 5 seconds for Delay Brew to lock in.
When activated, the unit will beep, and
DELAY BREW will remain illuminated.
5 To cancel, press DELAY BREW
or the Power button. Changing the
brew style while Delay Brew is set or
starting another brew will cancel the
programmed Delay Brew.
Fig. 7
Fig. 8
Fig. 9
ADJUSTABLE WARMING PLATE
The warming plate will turn on once the
brew has started. Press the STAY WARM
button after the brew to turn o the
warming plate (Fig� 9). You can turn
the warming plate back on by pressing
STAY WARM again. Wait until surface
has cooled completely before touching.
NOTE: DO NOT add additional water to the
reservoir when using the STAY WARM function.
You can program the warming plate to stay
on for up to 4 hours.
1 Press and hold STAY WARM until the
clock flashes, displaying the time at
which the warming plate is currently
set to turn o.
2 Quickly press the hour (H) or minute (M)
button to adjust the time up to 4 hours.
The warming plate is automatically
programmed to stay on for 2:00 hours.
3 To lock in the new duration, press
STAY WARM again, or wait 5 seconds
for it to lock in automatically.
CARE & MAINTENANCE
CLEANING AFTER A BREW
1 After the unit has cooled, remove the
filter holder from the brew basket. If
using a paper filter, discard it. If using
the permanent filter, wash it thoroughly
with soap and warm water or place on
the top rack of the dishwasher.
2 Empty the water reservoir and
hand-wash or place on the top rack
of the dishwasher.
NOTE: For best results, we recommend
rinsing the reservoir after brewing and refilling
with fresh water the next time you brew.
3 We recommend cleaning your carafe
with warm, soapy water, or placing
it on the top rack of your
dishwasher. If you want
to clean the carafe more
thoroughly, we recommend
using a soft foam brush such
as the one shown to the right.
4 After the coee maker
has cooled, wipe down the main unit,
showerhead, and water reservoir shelf
with a cloth and warm water. DO NOT
immerse the coee maker in water.
DESCALING YOUR
NINJA® COFFEE BREWER
NOTE: Make sure the SMALL BATCH
button is not selected/illuminated.
1 Set the empty carafe beneath the
brew basket.
2 Use a descaling solution specifically
formulated for coeemaker cleaning
and follow the directions on the package.
Fill the water reservoir up to, but not
exceeding, the 12-Cup Line (60 fl. oz.).
OR
Add 16 oz. of white vinegar to the water
reservoir, then fill the rest of the reservoir
with water up to, but not exceeding, the
12-Cup Line (60fl. oz.).
3 Once the water reservoir is filled with
your cleaning solution or vinegar mixture,
press the CLEAN button. The clean cycle
takes approximately 25–35 minutes. To
cancel the clean cycle, press the CLEAN
button again or press the Power button.
4 The unit will beep when the clean cycle
successfully completes. Refill the reservoir
with fresh water up to, but not exceeding,
the 12-Cup Line, and set the empty carafe
beneath the brew basket. Run a full Classic
Brew cycle with water only to remove any
cleaning solution that could aect the
flavor of your coee.
ENGLISH
PREPARING & USING YOUR
NINJA® COFFEE BREWER – CONT.