Caution : You must read this before you proceed 3 Seater Label Picture Description QTY A Left Armrest (with Legs) 1 B Right Armrest (with Legs) 1 C Backrest (with Legs) 3 D Seat Panel 3 E Front Panel (with Legs) 3 Noble House Home Furnishings LLC Page 1 OF 11
F Left Front Foot Clip 1 G Right Front Foot Clip 1 H Left Back Foot Clip 1 I Right Back Foot Clip 1 J Front Middle Foot Clip 2 K Back Middle Foot Clip 2 L Inner Panel (with Legs) 2 M Seat Cushion 3 Q Rubber Hammer 1 Before Beginning Assembly: Noble House Home Furnishings LLC Page 2 OF 11
Overview Backrest (C) Right Armrest (B) Seat Cushion (M) Left Armrest (A) Seat Panel (D) Right Front Foot Clip (G) Front Middle Foot Clip (J) Left Back Foot Clip (H) Left Front Foot Clip (F) Front Panel (E) Front Facing This 3 Seater has multiple parts and may require up to 60 minutes to assemble. To give you an overview of the 3 Seater parts, the above picture is to help you put the various parts into perspective.
Step 2 Clasp Pear-shaped Clasp Mounting Position Insert the Clasps of the Front Panel(E) into the large part of Pear-shaped Clasp mounting positions of the other Front Panel(E) as shown above. Button up the Clasps with the Rubber Hammer(Q) as pictured. Step 3 Dowel Align Inner Panel(L) to Middle Panel(E) as pictured above. Insert the Dowel of the Inner Panel into the mounting position of the Middle Panel until it clicks into place. Repeat this process with the remaining Inner Panel(L).
Step 4 Another side of Seat Board (D) Place the Seat Panels(D) facedown on the clean, non-marring surface. Insert the Clasps of the Seat Panel(D) into the large part of Pear-shaped Clasp mounting positions of the other Seat Panel(D) and push down to button up the Clasps with the Rubber Hammer(Q). Step 5 Insert the Clasps of the Seat Panel(D) into the large part of Pear-shaped Clasp mounting positions of the other Seat Panel(D) and push down to button up the Clasps with the Rubber Hammer(Q).
Step 6 With help from an adult partner, insert Front Panels(E) and Inner Panels(L) into Seat Panels(D) using the interlocking joints with Rubber Hammer(Q). Step 7 Place the Backrests(C) on the clean, non-marring surface. Insert the Clasps of the Backrest(C) into the large part of the Pear-shaped Clasp mounting positions on the other Backrest(C). Button up the Clasps with the Rubber Hammer(Q) as pictured.
Step 8 Insert the Clasps of the Backrest(C) into the large part of the Pear-shaped Clasp mounting positions on the other Backrest(C). Button up the Clasps with the Rubber Hammer(Q) as pictured. Step 9 With help from an adult partner, place the Backrests(C) on the Seat Panels(D) and Inner Panels(L) as shown above. Insert the Clasps of the Seat Panels(D) and Inner Panels(L) into the large part of Pear-shaped Clasp Mounting Positions of the Backrests(C).
Step 10 With the help of your adult partner, stand the assembly upright. Button up the Clasps with the Rubber Hammer(Q) left to right as pictured. Step 11 Align the Left Armrest(A) to the left side of Backrest(C), Seat Panel(D), and Front Panel(E). Insert the Clasps on the Left Armrest(A) into the Pear-shaped Clasp mounting positions on the Front Panel(E), Seat Panel(D), and Backrest(C).
Step 12 Repeat the process from Step 10, to assemble the Right Armrest(B) Step 13 Attach the Left Front Foot Clip(F), Right Front Foot Clip(G), Left Back Foot Clip(H), Right Back Foot Clip(I), Front Middle Foot Clips(J), and Back Middle Foot Clips(K) to the feet of the 3 Seater using the Rubber Hammer(Q) as shown above.
Step 14 With the help of your adult partner, stand the 3 Seater up on a Lever surface, to check for wobbles. If there are wobbles, use the Rubber Hammer(Q) to ensure all parts are properly secured. Step 15 Place the Cushion(M) on the seat. Your 3 Seater is ready for use. This 3 Seater can only be used on a flat, level surface.
Noble House Home Furnishings LLC Page 11 OF 11
Caution : You must read this before you proceed Club Chair Label Picture Description QTY A Left Armrest (with Legs) 1 B Right Armrest (with Legs) 1 C Backrest (with Legs) 1 Noble House Home Furnishings LLC Page 1 OF 7
D Seat Panel 1 E Front Panel (with Legs) 1 F Left Front Foot Clip 1 G Right Front Foot Clip 1 H Left Back Foot Clip 1 I Right Back Foot Clip 1 M Seat Cushion 1 Q Rubber Hammer 1 Before Beginning Assembly: Noble House Home Furnishings LLC Page 2 OF 7
Overview Backrest (C) Right Armrest (B) Left Armrest (A) Seat Cushion (M) Seat Panel (D) Front Panel (E) Left Back Foot Clip (H) Right Front Foot Clip (G) Left Front Foot Clip (F) Front Facing This Club Chair has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Club Chair parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 2 Clasp Pear-shaped Clasp Mounting Position Place the Backrest(C) upright and align Seat Panel(D) as shown above. There are four Pear-shaped Clasp mounting positions on the Backrest(C), and four Clasps on the Seat Panel(D). Insert the four Clasps into four mounting positions and push down to button up the Clasps with the Rubber Hammer(Q). Step 3 Pear-shaped Clasp Mounting Position Clasp Turn the assembly onto it's side as shown.
Step 4 Button up the Clasps with the Rubber Hammer(Q) from left to right as shown above. Step 5 With the help of an adult partner, turn the assembly over as shown above. Repeat the same process from Steps 3 - 4 with the Right Armrest(B).
Step 6 Attach the Left Front Foot Clip(F), Right Front Foot Clip(G), Left Back Foot Clip(H), Right Back Foot Clip(I) to the feet of the Club Chair using the Rubber Hammer(Q) as shown above. Step 7 With the help of your adult partner, stand the Club Chair up on a Lever surface, to check for wobbles. If there are wobbles, use the Rubber Hammer(Q) to ensure all parts are properly secured. Step 8 Place the Cushion(M) on the seat. Your Club Chair is ready for use.
Noble House Home Furnishings LLC Page 7 OF 7
Caution: You must read this before you proceed Loveseat Label Picture Description QTY A Left Armrest (with Legs) 1 B Right Armrest (with Legs) 1 C Backrest (with Legs) 2 D Seat Panel 2 E Front Panel (with Legs) 2 Noble House Home Furnishings LLC Page 1 OF 9
F Left Front Foot Clip 1 G Right Front Foot Clip 1 H Left Back Foot Clip 1 I Right Back Foot Clip 1 J Front Middle Foot Clip 1 K Back Middle Foot Clip 1 L Inner Panel (with Legs) 1 M Seat Cushion 2 Q Rubber Hammer 1 Before Beginning Assembly: Noble House Home Furnishings LLC Page 2 OF 9
Overview Backrest (C) Right Armrest (B) Seat Cushion (M) Left Armrest (A) Seat Panel (D) Right Front Foot Clip (G) Left Back Foot Clip (H) Front Middle Foot Clip (J) Left Front Foot Clip (F) Front Panel (E) Front Facing This Loveseat has multiple parts and may require up to 60 minutes to assemble. To give you an overview of the Loveseat parts, the above picture is to help you put the various parts into perspective.
Step 2 Align Inner Panel(L) to Middle Panel(E) as pictured above. Insert the Dowel of the Inner Panel into the mounting position of the Middle Panel until it clicks into place. Step 3 Another side of Seat Board (D) Place the Seat Panels(D) facedown on the clean, non-marring surface. Insert the Clasps of the Seat Panel(D) into the large part of Pear-shaped Clasp mounting positions of the other Seat Panel(D) and push down to button up the Clasps with the Rubber Hammer(Q).
Step 4 With help from an adult partner, insert Front Panels(E) and Inner Panels(L) into Seat Panels(D) using the interlocking joints with Rubber Hammer(Q). Step 5 Place the Backrests(C) on the clean, non-marring surface. Insert the Clasps of the Backrest(C) into the large part of the Pear-shaped Clasp mounting positions on the other Backrest(C). Button up the Clasps with the Rubber Hammer(Q) as pictured.
Step 6 With help from an adult partner, place the Backrests(C) on the Seat Panels(D) and Inner Panels(L) as shown above. Insert the Clasps of the Seat Panels(D) and Inner Panels(L) into the large part of Pear-shaped Clasp Mounting Positions of the Backrests(C). Step 7 With the help of your adult partner, stand the assembly upright. Button up the Clasps with the Rubber Hammer(Q) left to right as pictured.
Step 8 Align the Left Armrest(A) to the left side of Backrest(C), Seat Panel(D), and Front Panel(E). Insert the Clasps on the Left Armrest(A) into the Pear-shaped Clasp mounting positions on the Front Panel(E), Seat Panel(D), and Backrest(C). Insert the 8 Clasps of Front Panel(E), Seat Panel(D), and Backrest(C) into Pear-Shaped Clasp mounting positions of Left Armrest(A). Button up the Clasps with the Rubber Hammer(Q) from left to right as shown above.
Step 10 Attach the Left Front Foot Clip(F), Right Front Foot Clip(G), Left Back Foot Clip(H), Right Back Foot Clip(I), Front Middle Foot Clips(J), and Back Middle Foot Clips(K) to the feet of the 3 Seater using the Rubber Hammer(Q) as shown above. Step 11 With the help of your adult partner, stand the 3 Seater up on a Lever surface, to check for wobbles. If there are wobbles, use the Rubber Hammer(Q) to ensure all parts are properly secured. Step 12 Place the Cushion(M) on the seat.
Noble House Home Furnishings LLC Page 9 OF 9
Caution : You must read this before you proceed Table Label Picture Description QTY N Table Top 1 O Leg 4 Noble House Home Furnishings LLC Page 1 OF 4
Q Rubber Hammer 1 Before Beginning Assembly: Overview Table Top (N) Leg (O) Leg (O) Front Facing This Table has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 Leg Mounting Position Open the carton, and place all parts on a clean, non-marring surface. Place the Table Top(N) facedown on the clean, non-marring surface. Insert one Leg(O) into the mounting position on the Table Top(N), use the Rubber Hammer(Q) to secure the Leg as shown above. Repeat the same process with the remaining Legs(O). Step 2 Place the Table on a level surface to check the wobbles. If there are wobbles, use the Rubber Hammer(Q) to ensure Legs are properly secured.
Noble House Home Furnishings LLC Page 4 OF 4