Product Guide
Table Of Contents
- XS-2426G-A Product Guide
- Legal notice
- Contents
- List of tables
- List of figures
- About this document
- 1 What’s new
- 2 ETSI ONT safety guidelines
- 3 ETSI environmental and CRoHS guidelines
- 4 ANSI ONT safety guidelines
- 5 XS-2426G-A unit data sheet
- 5.1 Overview
- 5.2 XS-2426G-A part numbers and identification
- 5.3 XS-2426G-A general description
- 5.4 XS-2426G-A software and installation feature support
- 5.5 XS-2426G-A interfaces and interface capacity
- 5.6 XS-2426G-A LEDs
- 5.7 XS-2426G-A detailed specifications
- 5.8 XS-2426G-A GEM ports and T-CONTs
- 5.9 XS-2426G-A performance monitoring statistics
- 5.10 XS-2426G-A functional blocks
- 5.11 XS-2426G-A standards compliance
- 5.12 XS-2426G-A special considerations
- 6 Install a XS-2426G-A indoor ONT
- 7 Replace a XS-2426G-A indoor ONT
- 8 Configure a XS-2426G-A indoor ONT
- 8.1 Overview
- GUI configuration
- Viewing device information and connection status
- 8.5 Overview
- 8.6 Viewing device information
- 8.7 Viewing LAN status
- 8.8 Viewing WAN status
- 8.9 Viewing WAN IPv6 status
- 8.10 Viewing STA information
- 8.11 Viewing Neighboring Access Points
- 8.12 Viewing home networking information
- 8.13 Viewing optics module status
- 8.14 Viewing statistics
- 8.15 Viewing voice information
- Network configuration
- 8.16 Overview
- 8.17 Configuring LAN
- 8.18 Configuring LAN IPv6
- 8.19 Configuring WAN
- 8.20 Configuring WAN DHCP
- 8.21 Configuring Wireless 2.4GHz
- 8.22 Configuring Wireless 5GHz
- 8.23 Configuring wireless scheduling
- 8.24 Configuring IP routing
- 8.25 Configuring DNS
- 8.26 Configuring TR-069
- 8.27 Configuring GRE tunnel
- 8.28 Configuring Upstream (US) Classifier
- 8.29 Configuring QoS
- Security configuration
- Configuring the Application
- Maintenance
- 8.46 Overview
- 8.47 Configuring the password
- 8.48 Configuring LOID
- 8.49 Configuring SLID
- 8.50 Managing the device
- 8.51 Backing up the configuration
- 8.52 Restoring the configuration
- 8.53 Upgrading firmware
- 8.54 Rebooting the device
- 8.55 Resetting to factory defaults
- 8.56 Diagnosing WAN connections
- 8.57 Viewing log files
- RG Troubleshooting Counters
- 9 ONT configuration file over OMCI
2
Configure the following parameters:
Table 8-19 GRE Tunnel parameters
Field Description
Tunnel Name Select Create new GRE Tunnel or select an existing tunnel from the list.
The tunnel name is automatically assigned by the system.
Up to 4 GRE tunnels are supported.
WAN Interface Select a WAN interface from the list.
GRE tunnels can only be created on HSI-enabled WAN interfaces.
Primary Remote End
Secondary Remote End (optional)
Enter an IP address or FQDN that is unique in the system.
If the primary remote endpoint is down or unreachable, the secondary remote endpoint
becomes active, if configured.
The secondary remote endpoint remains active until it becomes unreachable, in which
case the primary remote endpoint becomes active again. Revertive mode is not
supported.
If both endpoints are unreachable, the GRE tunnel is declared down.
Connected Remote End This field displays the current data traffic path for the GRE tunnel.
Connectivity check This feature is automatically selected by the system.
Traffic timeout to start pings Enter the traffic timeout in seconds (2 to 1024).
No. of retries before unreachable Enter the number of retries before the tunnel is declared down (0 to 100).
Figure 8-24 GRE Tunnel page
Configure a XS-2426G-A indoor ONT
Network configuration
Configuring GRE tunnel
Nokia ONT
Draft Draft
Nokia – Proprietary and Confidential
Use pursuant to applicable agreements
3FE-49348-AAAA-TCZZA
December 2020
116 Issue 1