Product Guide
Table Of Contents
- XS-2426G-A Product Guide
- Legal notice
- Contents
- List of tables
- List of figures
- About this document
- 1 What’s new
- 2 ETSI ONT safety guidelines
- 3 ETSI environmental and CRoHS guidelines
- 4 ANSI ONT safety guidelines
- 5 XS-2426G-A unit data sheet
- 5.1 Overview
- 5.2 XS-2426G-A part numbers and identification
- 5.3 XS-2426G-A general description
- 5.4 XS-2426G-A software and installation feature support
- 5.5 XS-2426G-A interfaces and interface capacity
- 5.6 XS-2426G-A LEDs
- 5.7 XS-2426G-A detailed specifications
- 5.8 XS-2426G-A GEM ports and T-CONTs
- 5.9 XS-2426G-A performance monitoring statistics
- 5.10 XS-2426G-A functional blocks
- 5.11 XS-2426G-A standards compliance
- 5.12 XS-2426G-A special considerations
- 6 Install a XS-2426G-A indoor ONT
- 7 Replace a XS-2426G-A indoor ONT
- 8 Configure a XS-2426G-A indoor ONT
- 8.1 Overview
- GUI configuration
- Viewing device information and connection status
- 8.5 Overview
- 8.6 Viewing device information
- 8.7 Viewing LAN status
- 8.8 Viewing WAN status
- 8.9 Viewing WAN IPv6 status
- 8.10 Viewing STA information
- 8.11 Viewing Neighboring Access Points
- 8.12 Viewing home networking information
- 8.13 Viewing optics module status
- 8.14 Viewing statistics
- 8.15 Viewing voice information
- Network configuration
- 8.16 Overview
- 8.17 Configuring LAN
- 8.18 Configuring LAN IPv6
- 8.19 Configuring WAN
- 8.20 Configuring WAN DHCP
- 8.21 Configuring Wireless 2.4GHz
- 8.22 Configuring Wireless 5GHz
- 8.23 Configuring wireless scheduling
- 8.24 Configuring IP routing
- 8.25 Configuring DNS
- 8.26 Configuring TR-069
- 8.27 Configuring GRE tunnel
- 8.28 Configuring Upstream (US) Classifier
- 8.29 Configuring QoS
- Security configuration
- Configuring the Application
- Maintenance
- 8.46 Overview
- 8.47 Configuring the password
- 8.48 Configuring LOID
- 8.49 Configuring SLID
- 8.50 Managing the device
- 8.51 Backing up the configuration
- 8.52 Restoring the configuration
- 8.53 Upgrading firmware
- 8.54 Rebooting the device
- 8.55 Resetting to factory defaults
- 8.56 Diagnosing WAN connections
- 8.57 Viewing log files
- RG Troubleshooting Counters
- 9 ONT configuration file over OMCI
environments, and physical condition of infrastructure and handsets after years of service. The
values reflect minimum values and refer to products operated according to the intended use
conditions. See 3.2 “Hazardous Substances Table (HST)” (p. 28) for more information.
3.2
Hazardous Substances Table (HST)
This section describes the compliance of the OLT and ONT equipment to the CRoHS standard
when the product and sub assemblies contain hazardous substances beyond the MCV value. This
information is found in this user documentation where part numbers for the product and sub
assemblies are listed. It may be referenced in other OLT and ONT documentation.
In accordance with the People’s Republic of China Electronic Industry Standard Marking for the
Control of Pollution Caused by Electronic Information Products (SJ/T11364-2006), customers may
access the Nokia Hazardous Substance Table, in Chinese, from the following location:
• http://www.alcatel-sbell.com.cn/wwwroot/images/upload/private/1/media/ChinaRoHS.pdf
(http://www.alcatel-sbell.com.cn/wwwroot/images/upload/private/1/media/ChinaRoHS.pdf)
3.3 Other environmental requirements
Observe the following environmental requirements when handling the P-OLT or ONT equipment.
3.3.1 ONT environmental requirements
See the ONT technical specification documentation for more information about temperature ranges.
3.3.2 Storage
According to ETS 300-019-1-1 - Class 1.1, storage of ONT equipment must be in Class 1.1,
weather-protected, temperature-controlled locations.
3.3.3 Transportation
According to EN 300-019-1-2 - Class 2.3, transportation of the ONT equipment must be in packed,
public transportation with no rain on packing allowed.
3.3.4 Stationary use
According to EN 300-019-1-3 - Class 3.1/3.2/3.E, stationary use of ONT equipment must be in a
temperature-controlled location, with no rain allowed, and with no condensation allowed.
3.3.5 Material content compliance
European Union (EU) Directive 2002/95/EC, “Restriction of the use of certain Hazardous
Substances” (RoHS), restricts the use of lead, mercury, cadmium, hexavalent chromium, and
certain flame retardants in electrical and electronic equipment. This Directive applies to electrical
and electronic products placed on the EU market after 1 July 2006, with various exemptions,
including an exemption for lead solder in network infrastructure equipment. Nokia products shipped
to the EU after 1 July 2006 comply with the EU RoHS Directive.
Nokia has implemented a material/substance content management process. The process is
described in: Nokia process for ensuring RoHS Compliance (1AA002660031ASZZA). This ensures
ETSI environmental and CRoHS guidelines
Hazardous Substances Table (HST)
Nokia ONT
Draft Draft
December 2020
Issue 1 29
Nokia – Proprietary and Confidential
Use pursuant to applicable agreements
3FE-49348-AAAA-TCZZA