Product Guide
Table Of Contents
- XS-2426G-A Product Guide
- Legal notice
- Contents
- List of tables
- List of figures
- About this document
- 1 What’s new
- 2 ETSI ONT safety guidelines
- 3 ETSI environmental and CRoHS guidelines
- 4 ANSI ONT safety guidelines
- 5 XS-2426G-A unit data sheet
- 5.1 Overview
- 5.2 XS-2426G-A part numbers and identification
- 5.3 XS-2426G-A general description
- 5.4 XS-2426G-A software and installation feature support
- 5.5 XS-2426G-A interfaces and interface capacity
- 5.6 XS-2426G-A LEDs
- 5.7 XS-2426G-A detailed specifications
- 5.8 XS-2426G-A GEM ports and T-CONTs
- 5.9 XS-2426G-A performance monitoring statistics
- 5.10 XS-2426G-A functional blocks
- 5.11 XS-2426G-A standards compliance
- 5.12 XS-2426G-A special considerations
- 6 Install a XS-2426G-A indoor ONT
- 7 Replace a XS-2426G-A indoor ONT
- 8 Configure a XS-2426G-A indoor ONT
- 8.1 Overview
- GUI configuration
- Viewing device information and connection status
- 8.5 Overview
- 8.6 Viewing device information
- 8.7 Viewing LAN status
- 8.8 Viewing WAN status
- 8.9 Viewing WAN IPv6 status
- 8.10 Viewing STA information
- 8.11 Viewing Neighboring Access Points
- 8.12 Viewing home networking information
- 8.13 Viewing optics module status
- 8.14 Viewing statistics
- 8.15 Viewing voice information
- Network configuration
- 8.16 Overview
- 8.17 Configuring LAN
- 8.18 Configuring LAN IPv6
- 8.19 Configuring WAN
- 8.20 Configuring WAN DHCP
- 8.21 Configuring Wireless 2.4GHz
- 8.22 Configuring Wireless 5GHz
- 8.23 Configuring wireless scheduling
- 8.24 Configuring IP routing
- 8.25 Configuring DNS
- 8.26 Configuring TR-069
- 8.27 Configuring GRE tunnel
- 8.28 Configuring Upstream (US) Classifier
- 8.29 Configuring QoS
- Security configuration
- Configuring the Application
- Maintenance
- 8.46 Overview
- 8.47 Configuring the password
- 8.48 Configuring LOID
- 8.49 Configuring SLID
- 8.50 Managing the device
- 8.51 Backing up the configuration
- 8.52 Restoring the configuration
- 8.53 Upgrading firmware
- 8.54 Rebooting the device
- 8.55 Resetting to factory defaults
- 8.56 Diagnosing WAN connections
- 8.57 Viewing log files
- RG Troubleshooting Counters
- 9 ONT configuration file over OMCI
XS-2426G-A indoor ONTs provide the following functions:
• Dual-band concurrent 2x2 802.11b/g/n/ax 2.4 GHz and 2x2 802.11ac/ax MU-MIMO 5 GHz
• Supports 802.11b/g/n/ax 2x2 Wireless 2.4 GHz MIMO; Channel bandwidth 20, 40 MHz, auto
• Supports 802.11a/n/ac/ax 2x2 Wireless 5 GHz Mu-MIMO; Channel bandwidth 20, 40, 80 MHz,
auto
• Four Gigabit standard RJ-45 10/100/1000 Mbps, auto negotiating Ethernet ports and MDI/MDIX
auto sensing
• Two POTS ports with R-J11 connectors
• One USB 3.0 Type A ports
• XGS-PON Uplink, G.9807.1, G.988 series standard compliant
• 256MB NAND Flash with bad block management, 512MB DDR3 RAM, pin2pin compatible
design for possible upgrade of RAM/Flash
• Four RJ-45 10/100/1000 Ethernet ports with auto negotiation and MDI/MDIX auto sensing
• WLAN on/off push button
• WPS on/off push button
• LEDs on/off push button
• Reset button
• Triple-Play services, including voice, video and high speed Internet access
• Support for fax services
• Built-in layer 2 switch; Line Rate L2 traffic
• IP video distribution
Figure 5-1 XS-2426G-A ONT
POWER
LINK
AUTH
LAN1
LAN2
LAN3
LAN4
WPS
WLAN2.4G
WLAN5G
TEL1
TEL2
VOIP
INTERNET
USB
36550
XS-2426G-A unit data sheet
XS-2426G-A general description
Nokia ONT
Draft Draft
December 2020
Issue 1 43
Nokia – Proprietary and Confidential
Use pursuant to applicable agreements
3FE-49348-AAAA-TCZZA