Product Guide
Table Of Contents
- XS-2426G-A Product Guide
- Legal notice
- Contents
- List of tables
- List of figures
- About this document
- 1 What’s new
- 2 ETSI ONT safety guidelines
- 3 ETSI environmental and CRoHS guidelines
- 4 ANSI ONT safety guidelines
- 5 XS-2426G-A unit data sheet
- 5.1 Overview
- 5.2 XS-2426G-A part numbers and identification
- 5.3 XS-2426G-A general description
- 5.4 XS-2426G-A software and installation feature support
- 5.5 XS-2426G-A interfaces and interface capacity
- 5.6 XS-2426G-A LEDs
- 5.7 XS-2426G-A detailed specifications
- 5.8 XS-2426G-A GEM ports and T-CONTs
- 5.9 XS-2426G-A performance monitoring statistics
- 5.10 XS-2426G-A functional blocks
- 5.11 XS-2426G-A standards compliance
- 5.12 XS-2426G-A special considerations
- 6 Install a XS-2426G-A indoor ONT
- 7 Replace a XS-2426G-A indoor ONT
- 8 Configure a XS-2426G-A indoor ONT
- 8.1 Overview
- GUI configuration
- Viewing device information and connection status
- 8.5 Overview
- 8.6 Viewing device information
- 8.7 Viewing LAN status
- 8.8 Viewing WAN status
- 8.9 Viewing WAN IPv6 status
- 8.10 Viewing STA information
- 8.11 Viewing Neighboring Access Points
- 8.12 Viewing home networking information
- 8.13 Viewing optics module status
- 8.14 Viewing statistics
- 8.15 Viewing voice information
- Network configuration
- 8.16 Overview
- 8.17 Configuring LAN
- 8.18 Configuring LAN IPv6
- 8.19 Configuring WAN
- 8.20 Configuring WAN DHCP
- 8.21 Configuring Wireless 2.4GHz
- 8.22 Configuring Wireless 5GHz
- 8.23 Configuring wireless scheduling
- 8.24 Configuring IP routing
- 8.25 Configuring DNS
- 8.26 Configuring TR-069
- 8.27 Configuring GRE tunnel
- 8.28 Configuring Upstream (US) Classifier
- 8.29 Configuring QoS
- Security configuration
- Configuring the Application
- Maintenance
- 8.46 Overview
- 8.47 Configuring the password
- 8.48 Configuring LOID
- 8.49 Configuring SLID
- 8.50 Managing the device
- 8.51 Backing up the configuration
- 8.52 Restoring the configuration
- 8.53 Upgrading firmware
- 8.54 Rebooting the device
- 8.55 Resetting to factory defaults
- 8.56 Diagnosing WAN connections
- 8.57 Viewing log files
- RG Troubleshooting Counters
- 9 ONT configuration file over OMCI
Table 5-4 XS-2426G-A indoor ONT physical connections (continued)
Connection
1
Print Letters Description
On/Off button ON/OFF This button turns the ONT on or off.
USB port USB This connection is provided through 1 USB port on the side of the ONT. The ONT supports
external USB hard drives that can be made accessible to all LAN devices.
Fiber optic port The SC/APC fiber optic port is located at the back of the ONT and provides the connection for
the fiber optic cable.
Notes:
1. The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power
connector.
5.6 XS-2426G-A LEDs
Figure 5-4, “XS-2426G-A indoor ONT LEDs” (p. 50) shows the XS-2426G-A indoor ONT LEDs.
Table 5-5, “XS-2426G-A indoor ONT LED descriptions” (p. 51) provides LED descriptions for XS-
2426G-A indoor ONTs.
Figure 5-4 XS-2426G-A indoor ONT LEDs
TEL1LINK AUTH TEL2LAN1 LAN2 LAN3 LAN4POWER WPS VOIPWLAN2.4G WLAN5G USBINTERNET
TEL1LINK AUTH TEL2LAN1 LAN2 LAN3 LAN4POWER WPS VOIP
WLAN2.4G
WLAN5G
USBINTERNET
35958
XS-2426G-A unit data sheet
XS-2426G-A LEDs
Nokia ONT
Draft Draft
Nokia – Proprietary and Confidential
Use pursuant to applicable agreements
3FE-49348-AAAA-TCZZA
December 2020
50 Issue 1