Product Guide
Table Of Contents
- XS-2426G-A Product Guide
- Legal notice
- Contents
- List of tables
- List of figures
- About this document
- 1 What’s new
- 2 ETSI ONT safety guidelines
- 3 ETSI environmental and CRoHS guidelines
- 4 ANSI ONT safety guidelines
- 5 XS-2426G-A unit data sheet
- 5.1 Overview
- 5.2 XS-2426G-A part numbers and identification
- 5.3 XS-2426G-A general description
- 5.4 XS-2426G-A software and installation feature support
- 5.5 XS-2426G-A interfaces and interface capacity
- 5.6 XS-2426G-A LEDs
- 5.7 XS-2426G-A detailed specifications
- 5.8 XS-2426G-A GEM ports and T-CONTs
- 5.9 XS-2426G-A performance monitoring statistics
- 5.10 XS-2426G-A functional blocks
- 5.11 XS-2426G-A standards compliance
- 5.12 XS-2426G-A special considerations
- 6 Install a XS-2426G-A indoor ONT
- 7 Replace a XS-2426G-A indoor ONT
- 8 Configure a XS-2426G-A indoor ONT
- 8.1 Overview
- GUI configuration
- Viewing device information and connection status
- 8.5 Overview
- 8.6 Viewing device information
- 8.7 Viewing LAN status
- 8.8 Viewing WAN status
- 8.9 Viewing WAN IPv6 status
- 8.10 Viewing STA information
- 8.11 Viewing Neighboring Access Points
- 8.12 Viewing home networking information
- 8.13 Viewing optics module status
- 8.14 Viewing statistics
- 8.15 Viewing voice information
- Network configuration
- 8.16 Overview
- 8.17 Configuring LAN
- 8.18 Configuring LAN IPv6
- 8.19 Configuring WAN
- 8.20 Configuring WAN DHCP
- 8.21 Configuring Wireless 2.4GHz
- 8.22 Configuring Wireless 5GHz
- 8.23 Configuring wireless scheduling
- 8.24 Configuring IP routing
- 8.25 Configuring DNS
- 8.26 Configuring TR-069
- 8.27 Configuring GRE tunnel
- 8.28 Configuring Upstream (US) Classifier
- 8.29 Configuring QoS
- Security configuration
- Configuring the Application
- Maintenance
- 8.46 Overview
- 8.47 Configuring the password
- 8.48 Configuring LOID
- 8.49 Configuring SLID
- 8.50 Managing the device
- 8.51 Backing up the configuration
- 8.52 Restoring the configuration
- 8.53 Upgrading firmware
- 8.54 Rebooting the device
- 8.55 Resetting to factory defaults
- 8.56 Diagnosing WAN connections
- 8.57 Viewing log files
- RG Troubleshooting Counters
- 9 ONT configuration file over OMCI
Note: Upon login, the 10G PON Home Gateway page displays the WAN status block on
the bottom left part of each page. This block shows the WAN connection ID, the WAN
status, and any WAN errors.
This block is accurate upon login, but it is static.
Table 8-1 Device Information parameters
Field Description
Device Name Name on the ONT
Vendor Name of the vendor
Serial Number Serial number of the ONT
Hardware version Hardware version of the ONT
Boot version Boot version of the ONT
Software version Software version of the ONT
Chipset Chipset of the ONT
Device Running Time Amount of time the device has run since last reset in hours, minutes, and seconds
You can click Refresh to display up-to-date information.
END OF STEPS
Figure 8-2 Device Information page
Configure a XS-2426G-A indoor ONT
Viewing device information and connection status
Viewing device information
Nokia ONT
Draft Draft
December 2020
Issue 1 79
Nokia – Proprietary and Confidential
Use pursuant to applicable agreements
3FE-49348-AAAA-TCZZA