Installation Guide

ManualsBrandsNuvo Lighting ManualsChandeliersNuvo Lighting Fusion 9 Light 30-7/8" Wide Chandelier

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES

YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE

IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL

You don’t need special tools to install this fixture. Be sure to

follow the steps in the order given. Under no circumstances

should a fixture be hung on house electrical wires, nor should a

swag type fixture be installed on a ceiling, which contains a

radiant type heating system. Read instructions carefully. If you

are unclear as to how to proceed, consult a qualified electrician

NOTE: Proper wiring is essential for the safe operation of this

fixture.

FIXTURE ASSEMBLY

Carefully remove the fixture from the carton and check that all

parts are included as shown in figure. Be careful not to

misplace any of the screws or parts, which are needed to install

this fixture.

STEP 1: Spread the arms so that the arms are at equal

distance from each other.

STEP 2: Thread the loop (J) onto the nipple (K).

INSTALLATION

IMPORTANT: Do not attach fixture directly to outlet box.

STEP 1: Secure the mounting bar (A) to outlet box with the

outlet box screws (B).Thread the nut (D) onto the

nipple (E) so that five threads are exposed above the

nut (D). Insert the lock washer (C) and thread the

nipple (E) into the mounting bar (A), then secure with

the nut (D).

STEP 2: Thread the screw collar (H) onto the nipple (E). Slide

the screw collar ring (G) and the canopy (F) over the

chain (I). Open one link of chain (I); connect it to

fixture loop (J). Open the other one link of chain (I),

connect it to collar loop (H) and close the link.

BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.

STEP 3: Lace wires up through chain (I) and pas wires through

holes in collar loop (H). We recommend lacing wire up

through every other link of chain (I).

GROUNDING INSTRUCTIONS

STEP 1: Insert the green grounding screw into the hole with

two raised dimples on the mounting bar. Wrap the

ground wire from the fixture (if supplied) around the

green grounding screw, then connect it to ground

wire from the outlet box (if not fixed on the outlet box)

using a wire connector (not supplied). If ground wire

from the fixture is not supplied, wrap the ground wire

(if not fixed on the outlet box) from the outlet box

around the green grounding screw and tighten it.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE

POWER SUPPLY WIRES.

STEP 2: Take note of the color of the wire(s) on your fixture.

Identify which group your fixture wire(s) falls into and

connect the wires according to the directions below:

GROUP A: Connect to Black

House Wire

GROUP B: Connect to White

House Wire

BLACK WHITE

*PARALLEL WIRE (round &

smooth)

*PARALLEL WIRE (square &

ridged)

WHITE OR GREY WITH

TRACER

WHITE OR GREY WITHOUT

TRACER

BROWN GOLD OR BLACK

WITHOUT TRACER

BROWN, GOLD OR BLACK

WITH TRACER

*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer

wire is square shaped or ridged and the less tracer wire is

round in shape or smooth (seen best when viewed from wire

end.)

STEP 3: Take your fixture wire(s) from group A and place

evenly against the black wire from the outlet box. Do

NOT twist wires together before using wire connectors

STEP 4: Fit a wire connector over the wires and screw the

connector clockwise until you feel firmness.

STEP 5: Try gently to pull the connector off the wires. If you

can pull the connector off, carefully re-do steps 3 and

4 as above and check again for a firm connection.

STEP 6: Connect the fixture wire from group B to the white wire

from the outlet box in the same manner. Make sure no

bare wires can be seen outside wire connectors.

FINAL ASSEMBLY

STEP 1: After wires are connected, place the canopy (F) on

the ceiling and secure collar ring (G). Then tuck them

carefully inside outlet box.

STEP 2: Place the metal frames (M) the glass shades (N) and

the cups (P) over the sockets (L), then secure with the

retaining rings (O).

STEP 3: Install lamps. (Please do not exceed the maximum

capacity recommended on the socket.)

CLEANING

To clean, wipe fixture with a soft cloth. Clean glass with a mild

soap. Do not use abrasive materials such as scouring pads or

powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to

order replacement parts. Be sure to use exact wording from

illustration when ordering parts.

ITEM NO: 60-4689 60-4789

Summary of content (1 pages)

PAGE 1
INSTALLATION AND SAFETY INSTRUCTIONS FOR YOUR SAFETY WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF. GENERAL You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling, which contains a radiant type heating system. Read instructions carefully.