OceanLED Support INSTALL MANUAL Sport Series S3116s Single Colour S3124s Dual Colour S3166s Multi Colour Product kit includes: Light / Screws / Fuse Kit OceanLED reserve the right to change this document without notice. Please refer to www.oceanled.com for latest documentation. OceanLED INSTALL / Sport Series / 190617 / v7.
IMPORTANT: Please read the instructions completely before proceeding with the installation. These instructions supersede any other pre dated instructions if they differ. Chapter 1........................................................................................................................................................................................................4 An overview of the underwater light installation.
IMPORTANT PRECAUTIONS! ATTENTION INSTALLER: This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner and/ or operator of this equipment. CAUTION: (Risk Group 2): Possibly hazardous optical radiation emitted from this product. Do not stare at operating lamp. May be harmful to the eye. CLASS 3: This equipment is designed to operate at voltages of less than 50v DC.
1 CHAPTER ONE Chapter 1: Overview This handbook provides instructions to assist you in the installation and set up of the Sport Series lights from OceanLED. 1.1 Identifying your model S3116s Single Colour S3124s Dual Colour S3166s Multi Colour 1.2 DC power / fuse ratings The majority of installations will utilize onboard 12/24v DC power supply from a marine battery.
WARNING: ENSURE MOUNTING LOCATION IS FLAT AND CHECK INTERNALLY FOR EASE OF ACCESS IF THERE IS A RIB, STRUT OR OTHER HULL THAT MAY INTERFERE WITH THE INSTALLATION. AVOID MOUNTING LIGHTS ON SURFACES THAT ARE SUBJECTED TO HIGH SPEED WATER IMPACT E.G. PLANING SURFACES. 1.5 Finding the mounting location - UNDERWATER Considerations NOTE: To ensure correct dispersion of light underwater, ensure all Sport Lights are mounted with the correct orientation with logo facing upwards.
2 CHAPTER TWO Chapter 2: Installation Note: OceanLED makes every effort to protect our marine and fresh water environment as well as our natural resources. Please take care to keep packaging away from and out of the water by ensuring loose packaging materials are secured and not susceptible to being blown into the water. Please recycle all packaging materials as the sustainability of our environment is everyone's responsibility. WARNINGS: • Never use power tools to secure your lights; hand tighten only.
inside the hull, remove it with acetone before sanding. 4. Place light fixture into position or use mounting template provided. Mark the screw hole position and pilot drill using correct sized drill bit for included screws. 5. Always dry fit units before applying any sealant. 2.2 Installing the light fixture TIP: Use a suitable marine sealant such as 3M™ Marine Adhesive Sealant Fast Cure 4200FS.
5. Once you are satisfied that the unit is fully adhered onto the hull, you will notice that sealant has squeezed out from around the perimeter of the light. Using a cloth wipe off excess sealant to leave a clean seal. If you do not see sealant squeeze out from the body, you have not used enough sealant or tightened the unit enough to the hull. Carefully examine the installation to make sure the seal you have installed on the unit is fully water-tight.
Sport Multi Colour Wiring Diagram RED Fuse / Breaker Power Switch In-Line Fuse 12/24 vDC BLACK Optional push to break switch for Sport Multi Colour RED In-Line Fuse In-Line Fuse BLACK 2.4 - Finalize your OceanLED installation Test your lights Always test the lights BEFORE the boat goes back into the water. Failure to test prior to launch may require boat to re hauled out. At this final stage make sure all of the system is operational. See Chapter 3 Operation.
3 CHAPTER THREE Chapter 3: Operation 3.1 - Single Colour Strobe To enter strobe mode, toggle the power on and off quickly twice, then back on. They should now strobe in a pseudo-random pattern. The lights can be reset from strobe mode after 20 seconds of use. Simply turn off then back on again. 3.2 - Dual Colour Operation The Dual colour change has seven modes of operation; 1. 2. 3. 4. 5. 6. 7. Single colour white – this mode is entered when the light is first turned on.
3.4 Sport Multi Colour control with DC switch operation: The Sport Multi Colour has three modes of operation, single colour mode, cycle / programing mode, and strobe mode: 1. Single colour mode – this mode is entered when the light is first turned on. The light will be a single colour, either a default white, or a previously selected colour. 2. Strobe mode – to enter this mode, turn off the light for less than 1 second, then back on again.
4 CHAPTER FOUR Chapter 4: Maintenance and troubleshooting 4.1 - Cleaning Instructions Sea growth can collect quickly on the light and this can reduce the performance in just a few weeks. To prevent the build-up of sea growth, all OceanLED lights have been coated with a specialized Tritonium coating which makes the surface of the lens a non-stick layer which helps ward off long term barnacle buildup.
4.3 - Troubleshooting problems and their solutions Sport Series Problem Check Result Fix Light does not look bright. Check that there is no marine growth on the lens. Sea life / barnacles present. Clean the lens as per instruction booklet. Check voltage supply to the light is between 11v and 32v DC (The light will still work between 9 and 11 volts however at reduced brightness). Voltage is either too high or too low. Investigate reason for high or low voltage.
5 CHAPTER FIVE Chapter 5: Appendix SUPPLY CABLE CONDUCTOR SIZE CHART CABLE LENGTH (FEET) 14 CIRCUIT CURRENT 2 AMP 4 AMP 6 AMP 8 AMP 10 AMP 12 AMP 14 AMP 16 AMP 0-5 18 AWG 18 AWG 16 AWG 16 AWG 16 AWG 14 AWG 14 AWG 14 AWG 10-15 18 AWG 18 AWG 16 AWG 16 AWG 14 AWG 14 AWG 14 AWG 14 AWG 15-20 18 AWG 18 AWG 16 AWG 14 AWG 14 AWG 14 AWG 12 AWG 12 AWG 20-25 18 AWG 16 AWG 14 AWG 14 AWG 12 AWG 12 AWG 12 AWG 10 AWG 25-30 18 AWG 16 AWG 14 AWG 12 AWG 12 AWG 10 AWG 10
6 CHAPTER SIX Chapter 6: Warranty Statement: This warranty statement is for those products supplied to and sold from all territories internationally OceanLED stands by its products. In general terms, the company gives a full 2 year’s manufacturer’s warranty on all of its products from date of sale from OceanLED. Warranty replacements shall be covered for a period of 2 years from the date of the original product sale from OceanLED.
1.3.
5: GREY MARKET INTERNET POLICY Grey marketed products continue to be a threat to our worldwide distribution and dealer network. In order to proactively discourage this activity by Internet resellers of our product, OceanLED will not honor the warranty of products purchased via the grey market through internet resellers. The following notice will be added to OceanLED’s warranty cards, website and all internet sellers will be required to post the same notice.
If you are located in either North, Central or South America please contact the Warranty Department at: OceanLED USA LLC 778 South Military Trail Deerfield Beach Florida FL 33442-3025 United States Tel:+1(954) 523-2250 Fax:+1(954) 523-2249 Email sales@oceanledusa.
NOTES __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ ________________________________________________________
Please remove this page and keep for your files For technical assistance: Europe: service@oceanled.com The Americas: warranty@oceanledusa.com Warranty Serial Code(s): © 2017 Ocean LED Marine LTD All Rights Reserved Specifications are subject to change without notice.
