OFNA Racing 22692 Granite Way, Ste. B Laguna Hills, Ca. 92653 (949) 586-2910 Www.ofna.com RTR Instruction Manual PURE COMPETITION...........
REQUIRED FOR OPERATION THINGS NEEDED You will need to buy a few items to start the engine and run the car. • Use 20% nitro CAR fuel. Do not use airplane fuels, they will over heat engine. • Buy long glow plugs, like OFNA/PICCO P-7 (#51007). Use plugs without idle bar. Do NOT buy hot plugs, like the MC-59. In your box you will find.. • #10218 - Red “C” size glow heater P-7S Glow Fuel 20% 51007 #10211 Battery Pack 1000 NiMh 5cell, flat............... $29.95 #10214 Battery Charger, Overnite $7.
READ THIS BEFORE RUNNING Running a nitro kit is fun and easy, but to make this a safe and good experience you must observe a few rules. This kit is extremely fast, easily over 40MPH, and can seriously injure someone if you are not careful. Where to run car? • Any running area you choose must be dry. Do not run car near any water or wet dirt. • Do not run on public streets. It is very easy to have the car run over or damaged by hitting the curb. • Do not operate car in tight confined places.
* Align throttle servo same as shown. CHECKING ENGINE THROTTLE A C B 1. Insert AA batteries into transmitter (8 Pcs). 2.Turn on transmitter. 3.Turn on receiver. 4.Center throttle trims as shown . 1. Pull Full Throttle. 1. Push trigger to full brake position. 2. Adjust alum. Stopper to increase or decrease the brake. Brake © A Idle Position (A) Full Throttle (B) IMPORTANT CHECK RADIO THROTTLE AND STEERING SWITCHES BEFORE RUNNING CAR • Full throttle arm position.
ASSEMBLY OF THE CLUTCH INTO ENGINE 3 x 5mm Screw 3 X 8mm Washer Notes: Non-Pull Start Engines... • Alum. Washer behind the flywheel is not needed when using Force engines or similar types. O.S. Engines will require washer spacer. • To check!..place the brass corn #10330 (big hole) against the engine bearing, then flywheel. You should be covering one or two thread of the engine shaft. If this is the case, you do not need an additional washer behind the flywheel. You must cut the engine shaft if too long.
ASSEMBLY OF THE BRAKE SYSTEM #30800 2x8mm Screw 2x4mm Screw 3x12mm Screw Brake System Plastic Parts Set 2x6mm Washer Slider Servo Mount 2x25mm Screw 3X3mm Set Screw 2mm Tie-Rod End Scre w Cem ent A-80B 2mm Adjust Nut 3mm Nut Adjust Mount 2x6mm Washer 2mm Nut 2mm Tie-Rod End 2x4mm Screw ALIGN THROTTLE SERVO AND BRAKE SAME AS SHOWN ( Neutral Position ) Engine at idle ( Braking Position ) Brake is not on Brake is on Brake Adjust Nut ( Full Throttle Position ) Less Brake More Brake Loo
ASSEMBLY OF THE TIRES, FOAM INSERTS AND WHEELS - Red White Lime Yellow #86091 Mini XX- Pin Tire R #86044 #86045 #86046 #86047 17mm 5-Star Wheels Front Knuckle Arm Assembly #15071 17mm Wheel Nuts Always use tire foam donut when building tires. IN ST GL ANT UE Foam T TAN INS LUE G * Apply instant glue into the groove of the wheel. Rear Hub Assembly #81091 - Med/soft #81092 - Med. WE RECOMMEND CA GLUE FOR RUBBER TIRES.
ENGINE BREAK-IN AND TUNNING (BREAK-IN THE ENGINE BEFORE DRIVING THE CAR!) • Choose a wide clear outdoor location with low dirt and dust. • Set the car on box or holder with wheels off the ground. • Turn on radio and car. Make sure throttle is at idle position. • Fill fuel tank and set master engine needle. • Prime fuel line and Heat glow plug before pull starting engine. • When started, let engine fast idle for two tanks of fuel.
0 1:1 SCREW SHEET 10 20 30 40 50 mm 3 x 5mm Cap Screw 3 x 3mm Set Screw 3 x 10mm Cap Screw 3 x 5mm Set Screw 3 x 8mm Set Screw M3 Nut M4 Nut 3 x 12mm Cap Screw 3 x 10mm Set Screw 3 x 15mm Cap Screw 3 x 20mm Cap Screw 3 X 25mm Cap Screw 3 x 5mm Tapping Screw M3 Nylon Locknut 3 x 15mm Set Screw M4 Nylon Kocknut 4 x 4mm Set Screw 4 x 10 mm Set Screw M3 Flange Nut ( Steel ) 5 x 5mm Set Screw 2 X 6mm Washer 3 x 8mm Tapping Screw 2 x 4mm Screw 2mm X 7mm Washer 3 x 10mm Tapping Screw 2 x 5mm S
