1 ASSEMBLY OF THE FRONT AND REAR BALL DIFF. Step 1 37145 Step 2 40060 40060 2.6mm Nylon Nut 35958 .....x2 37110 Apply Grease Builds two differentials for front and rear. 37132 2.6x6x1mm Washer .....x4 37120 (12 Pcs) 37148 38288 35958 5x8mm Ball Bearing .....x4 Apply Grease 35958 37132 37132 37110 37132 2.6x25mm Screw 37132 37145 .....x2 2 CHECKING BALL DIFF. Step 1 Step 2 Parallel two Flat Head screw drives to the cap joint as show, and rotate the differential gear to check if it slip.
4 ASSEMBLY OF THE FRONT GEAR CASE 94050 2.6x10mm Do Not Over Tighten Step 1 37151 2x7.8mm Pin Step 2 90020 2.5mm E-Ring 94001 3x4mm 37151 .....x2 94050 2.6x10mm S Cecrew me nt .....x1 37147 37151 37147 94001 3x4mm Screw .....x1 Apply Grease 37430 2.5mm 38254 37143 38254 37148 38254 12x15x0.25mm Shim .....x2 94050 2.6x10mm Cap Screw .....x4 *Adjust the backlash with the shims. 37430 5x11mm Ball Bearing .....x2 37147 5 ASSEMBLY OF THE FRONT SHOCK STAY Step 1 94002 3x8mm Screw .....
7 ASSEMBLY OF THE SERVO SAVER AND THE STEERING TIE-ROD B Step 1 A Step 2 Steering Rod B Steering Servo Rod *Snap steering servo rod into 4mm ball & socket. *Made two steering rod for left and right hand side. 38280 (3x36mm) 37650 (Long) 38398 (3x20mm) 37650 (Long) A 37650 (Long) 37650 (Long) A 1:1 1:1 B *Approx. 7.5mm *Snap steering rod into 4mm ball & socket. *Approx. 20mm A 8 ASSEMBLY OF THE SERVO SAVER ONTO CHASSIS 3mm Do Not Over Tighten 3mm 94041 3mm Nylon Nut .....
10 ASSEMBLY OF THE KNUCKLE ARMS Assemble both right and left sides. Step 1 3x8mm Step 2 37390 2x10.8mm Pin .....x2 37220 37181 37220 Knuckle Arm Bushing 37640 37430 94002 3x8mm Screw Ensure Free Movement 37550 37430 .....x4 37590 37360 4mm Ball&Socket .....x2 3x8mm 37430 5x11mm Ball Bearing 37220 37390 .....x4 37360 11 ASSEMBLY OF THE KNUCKLE ARMS AND FRONT LOWER ARMS Assemble both right and left sides.
13 ASSEMBLY OF THE FRONT SUSPENSION ARMS Assemble both right and left sides E-69 94005 3x15mm Screw .....x2 3x15mm *Snap onto knuckle arm. 37170 *Assembly the front rod to shock tower as picture shown. 2.5mm 14 ASSEMBLY OF THE SUPR GEAR AND THE DIFF. MOTOR MOUNT Insert the 2mm pin before assemble the O-ring. 37151 2x7.8mm Pin .....x3 37151 37149 8x1.5mm O-Ring .....x1 37500 3x5mm 37430 37151 37148 37139 90020 2.5mm E-Ring .....x1 37149 3x5mm 37430 37151 94001 3x5mm Screw Imperial .....
16 ASSEMBLY OF THE REAR SHOCK STAY Step 1 Step 2 3x8mm 38282 .....x2 94003 3x10mm Screw .....x2 rew nt Sceme C 94002 3x8mm Screw 38282 w t re e n Sc em C 3x10mm 37135 17 ASSEMBLY OF THE REAR GEAR CASE ONTO CHASSIS 37138 (165.5mm) 94019 3x10mm Flat Head Screw .....x8 38263 *Insert the drive Shaft into the cap joint before assembly rear gear case onto chassis. Use the 0 degree for rear lower arm holder in front.
19 ASSEMBLY OF THE REAR UPPER ARMS Assemble both right and left sides. Step 1 Step 2 30403 30403 6mm Ball .....x4 38398 (3x20mm) 94006 3x18mm Screw .....x2 37100 (Long) 37100 (Short) 37690 30403 3x18mm 1:1 *Approx. 11mm 20 ASSEMBLY OF THE REAR ARM HOLDER Assemble both right and left sides. 38262 (3x50mm) 94019 3x10mm Flat Head Screw 3x10mm .....x2 38262 3x50mm Arm Shaft *Use the 0 degree for rear lower arm holder. .....
22 ASSEMBLY OF THE BATTERY HOLDER 3x10mm 3x10mm 3x10mm *Please assemble two Battery Holder before use. 37580 94019 3x10mm Flat Head Screw 37147 37410 .....x8 3x10mm 94003 3x10mm Screw .....x6 37580 37580 3x10mm 3x10mm 3x10mm 3x10mm 23 ASSEMBLY OF THE STEERING SERVO ONTO CHASSIS E-56 94040 3x8mm Washer 30661 .....x2 3x8mm 3x10mm 37360 4mm Ball&Socket .....x1 37360 3x8mm 94019 3x10mm Flat Head Screw 3x10mm .....x2 * Use the screw provided with your servo .
25 ASSEMBLY OF THE UPPER DECK 3x20 mm Do Not Over Tighten 3x8 mm 30560 3x20 mm Do Not Over Tighten 37134 3x8 mm 94002 3x8mm Screw .....x3 94007 3x20mm Screw .....x4 26 ASSEMBLY OF THE SHOCKS *Assemble 4 sets for front and rear. CORRECT SHOCK ASSEMBLY 39030 *Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ballend and the shock body is 9.5mm for thefront. 2mm Step 1 2mm 2mm E-Ring *N.B. Do not over tighten as the plastic will strip.
27 ASSEMBLY OF THE SHOCK INTO FRONT AND REAR SHOCK STAY Front shock Rear shock 37360 37360 37360 4mm Ball&Socket *Snap ball end into 37360. .....x4 Assemble both right and left sides. *Snap ball end into 37360. 28 ASSEMBLY OF THE ELECTRIC SPEED CONTROLLER AND RECEIVER Electric Speed Controller *Use two-sided adhesive tapes. Tear off the paper before use.
30 ASSEMBLY OF THE FRONT BUMPER AND FOAM BUMPER Step 1 94002 3x8mm Screw *To the hole on the top of gear box. 3x8mm Step 2 38294 .....x1 38291 94019 3x10mm Flat Head Screw .....x2 94004 3x12mm Screw .....x2 94021 3x15mm Flat Head Screw .....x1 3x12mm 3x10mm 3x12mm 3x15mm 31 INSERT BATTERY INTO BATTERY HOLDER Step 1 Step 2 Step 3 *Remove the screw and turn the battery cover as picture shown.
33 ASSEMBLY OF THE TIRE ONTO FRONT KNUCKLE AND REAR HUB Assemble both right and left sides. 30560 94042 4mm Nylon Nut .....x4 *Tire and wheel assembly. 4mm 34 ASSEMBLY OF THE BODY AND PAINTING (BODY NOT INCLUDED) Cut out the body as shown. Body(Not included) *Use dishwashing liquid to remove any dirt and oil from inside. Cut Out Before cutting and making holes on the body, put the unpainted body on the chassis to confirm the mounting position and location for holes and cutouts.
35 ASSEMBLY OF THE WING Double side Tape Step 1 Step 2 *Use body reamer or tool to make a 3mm hole as Picture Shown. Step 3 * paint the color to the rear wing from back side. Do Not Over Tighten Side Plate Double side Tape *Take off the paper from double side tape before assembly. Spray Paint Cut Out 3x8mm Body Reamer (Not included) Side Plate Side Plate 94002 3x8mm Screw Cut Out .....
PLASTIC PARTS USED 30661 SERVO HORN 37148 BEVEL GEAR (SMALL & LARGE) (2 Set) 37560 REAR HUB & SERVO MOUNT 37147 FRONT AND REAR GEAR BOX & SERVO SAVER (2 Set) 37145 BALL DIFF.
PLASTIC PARTS USED 37100 SHOCK ABSORBER (4 Pcs) 37590 DRIVE NUT 37580 BATTERY HOLDER SET 37500 SPUR GEAR(82T) 38291 BUMPER 39320 FRONT AND REAR BODY POST (2 Set) SYMBOL USED THROUGHOUT THE INSTRUCTION MANUAL Parts Bag Used Degrease With Motor Spray Do Not Over Tighten Tighten BAG Do Not Over Tighten Screw Cement Apply Screw Cement Apply Oil Oil Tighten Apply Grease Apply Grease Ensure Free Movement True-To-Scale 1:1 Ensure Free Movement Contact Adhesive Contact Adhesive Anti-clockwise
IMPORTANT-READ THIS BEFORE RUNNING Running nitro kit is fun and easy, but to make this a safe and good experience you must observe a few rules. This kit is extremely fast, easily over 50MPH, and can seriously injure someone if you are not careful. 1. W here to r un car? Any running area you choose must be dry. Do not run car near any water or wet dirt. Do not run on public streets. It is very easy to have the car run over or be damaged by hitting the curb. Do not operate the car in tight confined places.
34720 JL-10E PARTS LIST OFNA 30212 30403 30661 35958 36742 37070 37080 37090 37100 37110 37120 37132 37133 37134 37135 37136 37137 37138 37139 37142 37143 37144 37145 37146 37147 37148 37149 37151 37170 37181 37201 37220 37360 37370 37390 37410 37430 37450 37500 37550 37560 37590 37600 37640 DESCRIPTION BEARING 5x8, FLANGE, 2 PCS. 6mm BALL, STEEL (NO COLLAR) SERVO HORN HEAVY DUTY BLACK BEARING, 5X8mm 1 PC. BUSHING, SERVO SAVER SHOCK, O-RINGS, 8 PCS JL10 SHOCK, PRESSURE CAP 4 PCS JL10 CAP, SHOCK, 4 PCS.
OWNER’S REGISTRATION CARD OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling this kit will provide many hours of enjoyment. The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date.