MOC3051M, MOC3052M 2M, MOC3053M 6-Pin DIP Random-Phase hase Triac Driver Optocoupler (600 (6 Volt Peak) www.onsemi.com The MOC3051M, MOC3052M and MOC3053M MOC305 consist of a GaAs infrared emitting diode optically coupled to a non-zeronon crossing silicon bilateral AC switch (triac). These devices isolate low voltage logic from 115 VAC and 240 VAC lines to provide random phase control of high current triacs or thyristors.
MOC3051M, MOC3052M, MOC3053M SAFETY AND INSULATIONS RATINGS As per DIN EN/IEC 60747-5-5, this optocoupler is suitable for “safe electrical insulation” only within the safety limit data. Compliance with the safety ratings shall be ensured by means of protective circuits. Parameter Characteristics Installation Classifications per DIN VDE 0110/1.89 Table 1, For Rated Mains Voltage < 150 VRMS I–IV < 300 VRMS I–IV Climatic Classification 40/85/21 Pollution Degree (DIN VDE 0110/1.
MOC3051M, MOC3052M, MOC3053M MAXIMUM RATINGS (Note 1) TA = 25°C unless otherwise specified. Symbol Parameters Value Unit Total Device TSTG Storage Temperature -40 to +150 °C TOPR Operating Temperature -40 to +85 °C -40 to +100 °C 260 for 10 seconds °C TJ TSOL Junction Temperature Range Lead Solder Temperature Total Device Power Dissipation at 25°C Ambient 330 mW Derate Above 25°C 4.
MOC3051M, MOC3052M, MOC3053M ELECTRICAL CHARACTERISTICS TA = 25°C unless otherwise specified. INDIVIDUAL COMPONENT CHARACTERISTICS Symbol Parameters Test Conditions Min. Typ. Max. Unit EMITTER VF Input Forward Voltage IF = 10 mA 1.18 1.50 V IR Reverse Leakage Current VR = 3 V 0.05 100 µA IDRM Peak Blocking Current, Either Direction VDRM = 600 V, IF = 0 (Note 2) 10 100 nA VTM Peak On-State Voltage, Either Direction ITM = 100 mA peak, IF = 0 2.2 2.
MOC3051M, MOC3052M, MOC3053M TYPICAL CHARACTERISTICS 400 ITM - ON-STATE CURRENT (mA) VF - FORWARD VOLTAGE (V) 1.7 1.6 1.5 1.4 1.3 TA = -40 °C 1.2 TA = 25 °C 1.1 TA = 85 °C 1.0 0.9 300 200 100 0 -100 -200 -300 -400 1 10 100 -3 -2 IF - LED FORWARD CURRENT (mA) 1.4 NORMALIZED TO TA = 25°C 1.2 1.0 0.8 -20 0 20 40 60 80 100 2 3 NORMALIZED TO PW = 100µs 10 5 0 1 10 100 PW - LED TRIGGER PULSE WIDTH (µs) Figure 3. LED Trigger Current vs. Ambient Temperature Figure 4.
MOC3051M, MOC3052M, MOC3053M APPLICATIONS INFORMATION Basic Triac Driver Circuit LED Trigger Current vs. Pulse Width The random phase triac drivers MOC3051M, MOC3052M and MOC3053M can allow snubberless operations in applications where load is resistive and the external generated noise in the AC line is below its guaranteed dv/dt withstand capability. For these applications, a snubber circuit is not necessary when a noise insensitive power triac is used. Figure 7 shows the circuit diagram.
MOC3051M, MOC3052M, MOC3053M TRIAC DRIVER VCC RLED R POWER TRIAC AC LINE CONTROL RET. Q LOAD RLED = (VCC – VFLED – VSATQ) / IFT R = VPAC / ITSM Figure 7. Basic Driver Circuit Figure 8. Triac Driver Circuit for Noisy Environments Figure 9. Triac Driver Circuit for Extremely Noisy Environments 0° 180° AC Line LED PW LED Current LED turn off min. 200µs Figure 10. Minimum Time for LED Turn Off to Zero Crossing www.onsemi.
MOC3051M, MOC3052M, MOC3053M REFLOW PROFILE Profile Feature Pb-Free Assembly Profile Temperature Minimum (Tsmin) 150°C Temperature Maximum (Tsmax) 200°C Time (tS) from (Tsmin to Tsmax) 60 seconds to 120 seconds Ramp-up Rate (TL to TP) 3°C/second maximum Liquidous Temperature (TL) 217°C Time (tL) Maintained Above (TL) 60 seconds to 150 seconds Peak Body Package Temperature 260°C +0°C / –5°C Time (tP) within 5°C of 260°C 30 seconds Ramp-down Rate (TP to TL) 6°C/second maximum Time 25°C t
MOC3051M, MOC3052M, MOC3053M ORDERING INFORMATION (Note 5) Device Package Shipping MOC3051M DIP 6-Pin Tube (50 Units) MOC3051SM SMT 6-Pin (Lead Bend) Tube (50 Units) MOC3051SR2M SMT 6-Pin (Lead Bend) Tape and Reel (1000 Units) MOC3051VM DIP 6-Pin, DIN EN/IEC60747-5-5 Option Tube (50 Units) MOC3051SVM SMT 6-Pin (Lead Bend), DIN EN/IEC60747-5-5 Option Tube (50 Units) MOC3051SR2VM SMT 6-Pin (Lead Bend), DIN EN/IEC60747-5-5 Option Tape and Reel (1000 Units) MOC3051TVM DIP 6-Pin, 0.
MOC3051M, MOC3052M, MOC3053M PACKAGING DIMENSIONS 8.89 4 1 3 7.62 (TYP) 6.10-6.60 6.60 8.13-8.89 6 PIN 1 15.0° (TYP) 0.20-0.30 3.28-3.53 NOTES: A) NO STANDARD APPLIES TO THIS PACKAGE. B) ALL DIMENSIONS ARE IN MILLIMETERS. 0.38 (MIN) (0.86) 2.54-3.81 5.08 (MAX) 0.25-0.36 C) DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, AND TIE BAR EXTRUSION D) DRAWING FILENAME AND REVSION: MKT-N06BREV4. 2.54 BSC 0.41-0.51 1.02-1.78 0.76-1.14 6 LEAD MDIP OPTO WHITE 0.3" WIDE www.onsemi.
MOC3051M, MOC3052M, MOC3053M (2.54) 6 4 1 3 (10.54) (1.52) (7.49) (1.78) 6.10-6.60 8.43-9.90 8.13-8.89 (0.76) PIN 1 LAND PATTERN RECOMMENDATION 5.08 (MAX) 3.28-3.53 0.25-0.36 2.49 1.89 0.38 (MIN) 0.20-0.30 2.54 (BSC) 0.16-0.88 (0.86) 0.41-0.50 (8.13) 1.02-1.78 0.76-1.14 NOTES: A) NO STANDARD APPLIES TO THIS PACKAGE. B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, AND TIE BAR EXTRUSION D) DRAWING FILENAME AND REVSION : MKT-N06CREV4.
MOC3051M, MOC3052M, MOC3053M 8.13-8.89 4 6.10-6.60 6 0.20-0.30 PIN 1 1 10.16-10.80 3 2.54-3.81 3.28-3.53 5.08 (MAX) 0.25-0.36 NOTES: A) NO STANDARD APPLIES TO THIS PACKAGE. B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, AND TIE BAR EXTRUSION D) DRAWING FILENAME AND REVSION: MKT-N06Drev4 0.38 (MIN) (0.86) 0.41-0.51 1.02-1.78 2.54 BSC 0.76-1.14 6 LEAD MDIP OPTO WHITE 0.4" LEAD SPACING www.onsemi.
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
