FAQ

ManualsBrandsOregon ManualsCordless Hedge Trimmers24 in. 40-Volt 4.0 Ah Battery and Rapid Charger Cordless Hedge Trimmer Kit

Oregon Outdoor Power Equipment FAQs

Do you have a question about an Oregon product? We’re here to help you get the answers you need so you

can get back to work.

General FAQs

Questions regarding product fit and compatibility -

For direct product fit-up questions, please speak with one of our Technical Services Experts at 1-800-223-

5168, option # 1 for the quickest response.

Questions regarding locating your nearest retailer store, item availability, and shipping -

Please contact the store directly/use store location lookup feature

Where are Oregon products made?

Oregon operates production facilities globally including the US and China.

______________________________________________________________________________________________________________________________

CS300 Cordless Chainsaw

When using the CS300 chainsaw, how long does the battery last?

The 4.0 Ah Battery Pack will last up to 400 cuts per charge in 2 to 3 inch (5 to 7 cm) diameter limbs. This

performance may vary with user technique, chain sharpness, size, and type of wood. The 2.6 Ah Battery Pack

will make up to 250 cuts. Cuts per charge will drop significantly with increasing diameter wood. The new 6.0

Ah Battery pack will bring 50% more run time compared with the 4.0 Ah Battery pack.

What is PowerSharp® (the red lever) and how does it work?

PowerSharp is a chain sharpening system that is built-in to Oregon chainsaw models. When the chain is dull

or not cutting fast enough, bring the chainsaw to full speed, pull the red lever for 3 to 5 seconds, and the chain

will work like new. Expect approximately 10 to 20 resharpenings on an individual PowerSharp® chain

depending on how much the chain was damaged prior to sharpening.

Can a non-PowerSharp® type chain be used on the CS300 chainsaw?

Yes. Other chains can be used on the chainsaw; however, the integrated sharpening feature will only work

with PowerSharp chain. When installing another chain type, remove the sharpening stone as non-

PowerSharp chains can be damaged by operating the red lever when a sharpening stone is installed. For the

CS300, 3/8-in. Low Profile™, .050″ gauge chain with 56 drive links can be used as an alternate chain.

Can I put a shorter or longer guide bar on the saw?

It is not recommended to install a guide bar longer than 16 inches (40 cm) onto the CS300. The CS300

chainsaw has been designed with a 16 inch (40 cm) guide bar as the optimal length. Performance will

decrease with a longer guide bar. Shorter guide bars with an A041 tail mount can be fitted to the CS300.

Does the chainsaw use bar and chain oil?

Summary of content (4 pages)

PAGE 1
Oregon Outdoor Power Equipment FAQs Do you have a question about an Oregon product? We’re here to help you get the answers you need so you can get back to work. General FAQs Questions regarding product fit and compatibility For direct product fit-up questions, please speak with one of our Technical Services Experts at 1-800-2235168, option # 1 for the quickest response.
PAGE 2
Yes. Bar and chain oil is required to properly lubricate the cutting system. Oregon Premium Bar and Chain Oil is recommended. Place the chainsaw on its side and fill the oil reservoir accessed through the oil cap. Check oil level each time you recharge the battery and fill as needed. ______________________________________________________________________________________________________________________________ BL300 Cordless Leaf Blower When using the BL300 leaf blower, how long does the battery last? A 4.
PAGE 3
The pole saw extends from 7’3″ to 10’4″ (2.2 m to 3.15 m) in length allowing up to approximately 15 feet (4.57 m) of access (based on a 5’10” individual operating at a 60 degree angle). How much does the PS250 weigh? The Oregon PS250 weighs 13.5 lbs. with battery installed. What types of chain can be used on the pole saw? Micro-Lite ® Narrow-Kerf 3/8″ Low-Profile .043 gauge saw chain (Oregon R34, 90SG034G) is recommended for the PS250, but any 3/8" Low-Profile .043 gauge chain with 34 drive links will work.
PAGE 4
Can I use the extension with all the attachments? No, the EX600 extension can only be used with the PS600 and HT600 attachments. Do not use more than one extension. Can I use a non-Oregon® attachment with the Powerhead? No. This Oregon Powerhead is designed to be used only with the Oregon attachment models. Use of other attachments could cause serious personal injuries. Can I use the Oregon attachments with a non-Oregon Powerhead? No.