Installation & Assembly

ManualsBrandsOttLite ManualsLightingWellness 19" Silver Desk Lamp with USB and Outlet

Harmonize LED Desk Lamp with USB

CO NGR ATUL ATI ONS !

PRODUCT REGISTRATION FORM

LAMP ASSEMBLY

Remove lamp from packing placing lamp body base (A) on a ﬂat

steady surface.

2. Attach counterbalance (C) to arm (D) by turning clockwise until snug.

Connect power adapter input (K) into connector (L) in the rear-bottom of

the lamp.

4. Plug the A/C adapter (J) into a standard household 120V AC outlet.

Note: Only use with the supplied AC adapter to avoid damage or

re.

5. Power switch (B) is a “touch” switch that controls ON/OFF power, the

LED brightness settings, and the color mode function of the lamp.

6. To power LED settings, slightly touch the switch to achieve the

following:

• t u r n l a m p “ O N ” t o 1 s t b r i g h t n e s s e t t i n g ; t o u c h t h e s w i t c h “ o n c e ” ;

• for 2nd brightness setting; touch the switch “two-times”;

• for 3rd brightness setting; touch the switch “three-times”;

• to turn lamp “OFF”; touch the switch “four-times”.

7. This lamp provides three color modes. To adjust lighting color

mode “touch” switch (B) to turn “ON” lamp, then slightly

“touch” switch (B) and keep depressed 1-2 seconds to change

l i g h t c o l o r t e m p e r a t u r e m o d e ; 5 0 0 0 ° K , 4 0 0 0 ° K , 2 7 0 0 ° K .

NOTE: The lamp will remember the last color mode setting.

8. To adjust height and angle of the shade (F) turn thumbscrew (H)

counterclockwise to loosen, adjust arm (D) to desired height, then turn

thumbscrew (H) clockwise to tighten. Adjust joint (E) and/or rotate the

shade (F) until desired position is achieved. To avoid damage to the

lamp, DO NOT OVERTIGHTEN as this would strip the thread.

SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS

1. Turn lamp off and WAIT UNTIL LAMP HEAD (F) IS COOL

before handling.

2. The LED panel (G) might get hot after several hours of continuous

use, DO NOT place your hands directly on LED light panel.

3. Never use with an extension cord unless the plug can be fully

inserted into the receptacles in the extension cord.

4. Do not alter the plug.

5. The lamp head included with this unit cannot be replaced by the

consumer.

6. INDOOR USE ONLY.

NOTE: The important safety instructions appearing in this instruction

sheet are not meant to cover all possible conditions and situations that

may occur. It must be understood that common sense, caution, and

care must be used with any electrical product.

CAUTION! IF THE ExTERNaL FLExIbLE CabLE OR CORD OF THIS LUmINaIRE

IS DamagED, IT SHaLL bE ExCLUSIvELY REPLaCED bY THE maNUFaCTURER OR ITS

SERvICE agENT OR a SImILaR qUaLIFIED PERSON IN ORDER TO avOID a HazaRD.

INDOOR USE ONLY.

CAUTION! THE LIgHT SOURCE OF THIS LUmINaIRE IS NOT REPLaCEabLE;

WHEN THE LIgHT SOURCE REaCHES IT’S END OF LIFE THE WHOLE LUmINaIRE

SHaLL bE REPLaCED.

FCC PART 15

Note: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that the interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that of the receiver.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

AC/DC ADAPTER

Input: AC 100-240V, 50/60 Hz, 1A

Output: 24V DC, 1A with a Male DC Plug

THIS LAMP CONTAINS a 5V-2.1A USB output port (N) located on the

bottom rear of lamp. USB port can charge such items as tablets, cellular

phones, etc.

EngliSH Harmonize LED Desk Lamp with USB

You’ve purchased the ﬁnest in natural lighting technology with your

new product.

Please complete the enclosed Product Registration Form and return it

today by mail, or register online .

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

CAUTION: Any change or modifcation to product not expressly

recognized by us voids our responsibility for proper function of

product.