Installation & Assembly
Extra Wide Area LED Clamp Lamp
49602C 49602C-SHPR ACDL583A
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with
your new OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and return
it today by mail, or register online by going to: OttLite.com/warranty
WARNING: To prevent electrical shock, make sure the lamp
is not plugged in until fully assembled per instructions.
LAMP ASSEMBLY
1.
Remove lamp body (A) and shade assembly (B) from packaging.
2. Determine lamp position to be used on a standard horizontal
table. See diagram 1 and 2.
3. Grasp lamp body (A) and mount clamp (D) on to the preferred
edge of table. NOTE: Adjust clamp knob (E) as needed.
Clamp must fully touch table surface. Do not use clamp as
noted in diagram 3.
4. Connect shade assembly (B) to flex neck (C). Secure shade
assembly (B) using screw (M). Screw (M) is to be tightened
with provided hex tool (N). DO NOT overtighten screw (M) as
it can strip. See diagram 4.
5. Connect power adapter input (F) into lamp cord connection (G).
6. Plug power adapter (H) into a standard household 120V AC
outlet. NOTE: Only use with supplied power adapter to avoid
damage or fire.
LAMP OPERATION
1. Turn the lamp ON or OFF by depressing switch (J) located on
the front of the shade assembly (B).
2. To power LED lighting, slightly touch switch (J) to achieve the
following:
• to turn lamp “ON”; touch the switch “once”
• to turn lamp “OFF”; touch the a “second” time.
3. This lamp provides three color modes and five levels of LED
brightness.
4. To adjust lighting color mode: touch “MODE” key (K) to switch
light color temperature mode; 3000K, 4000K, 5000K.
5. To adjust LED brightness settings, slightly touch “UP” or
“DOWN” arrows (L). Upon turning ON lamp, it will initially set
at the 3rd LED brightness setting.
NOTE: The lamp will return to lamp setting last employed
unless disconnected from adapter.
6. To reposition the light, grasp fleck neck (C) to position as
desired. Take care not to overextend the lamp to avoid
damage.
SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS
1. Turn lamp off and WAIT UNTIL SHADE ASSEMBLY (B) AND
ADAPTER (H) ARE COOL before handling.
2. Shade assembly (B) might get hot after several hours of
continuous use, DO NOT place your hands directly on the
surface of lamp head.
3. Never use with an extension cord unless the plug can be fully
inserted into the receptacles in the extension cord.
4. Do not alter the plug.
5. The lamp head included with this unit cannot be replaced by
the consumer.
6. INDOOR USE ONLY.
NOTE: The important safety instructions appearing in this
instruction sheet are not meant to cover all possible conditions
and situations that may occur. It must be understood that
common sense, caution, and care must be used with any
electrical product.
CAUTION! IF THE ExTERNaL FLExIbLE CabLE OR CORD OF THIS LUmINaIRE
IS DamagED, IT SHaLL bE ExCLUSIvELY REPLaCED bY THE maNUFaCTURER OR ITS
SERvICE agENT OR a SImILaR qUaLIFIED PERSON IN ORDER TO avOID a HazaRD.
INDOOR USE ONLY.
FCC PART 15
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that of
the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
CAN ICES-005 (B)/NMB-005 (B)
CAUTION: Any change or modification to product not expressly
recognized by OttLite Technologies voids OttLite’s responsibility
for proper function of product.
AC/DC ADAPTER
Input: AC 100-240V, 50/60 Hz, 0.35A
Output: 20V DC, 0.37A with a Male DC Plug
ACCESSORY: Hex Tool
EngliSH Extra Wide Area LED Clamp Lamp
INS180419 REV050818
A
M
B
C
D
E
G
H
F
Diagram 3
adjustable
0-2½ in.
0-65mm
Touch Switch
M
Do not use clamp in the below situation
Diagram 1
Diagram 2
Diagram 4
LJ K
C
B
N