RPK4-FD2201 Pacific Accessory Corporation Now Including Button Trim Options! For Trucks With 2 Separate Buttons For Trucks With 3 Separate Buttons The following information replaces Step 2 of the assembly section on Page 5 of the RPK4-FD2201 installation instructions. The required upper dash button trim panel will depend on whether the vehicle has two or three separate buttons. Insert the appropriate upper dash button trim bezel into the RPK4-FD2201 kit.
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty Introduction & Features The RPK4-FD2201 is a complete radio replacement kit with integrated climate control retention for the 2015-2018 Ford F-150 and 2017-2018 Ford Super Duty equipped with the 4” screen. This kit utilizes the factory HVAC control knobs for a more factory look and experience.
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty Installation Part One: Disassembly of Factory Dash 1. Remove front dash panel from vehicle by prying up on the top dash panel with a plastic pry tool, then removing the two 7mm screws located under the top dash panel. 2. Remove the factory screen, SYNC module (if equipped), and Audio Control Module (ACM) using a 7mm socket. These parts are no longer needed.
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty Part Two: Disassembly of Factory Dash Panel 1. Remove hazard and traction control buttons from factory dash panel by pushing in on the release tabs. Set aside for later use. 4. Make sure that the white line on the temperature control knob is centered at the top. Remove back of factory dash panel by releasing the locking tabs on each side. 2.
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty Disassembly of Factory Dash Panel (cont.) 7. Remove (6) T10 16mm screws from bottom circuit board. Set aside for later use. 8. Remove bottom circuit board and set aside for later use. 9. Remove temperature control and fan speed knobs. Set aside for later use. 10. Remove HVAC buttons (make sure the rubber button pad comes with it). Set aside for later use. 11.
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty Disassembly of Factory Dash Panel (cont.) This is the end of part two. Please continue to the next section to begin part three. 13. Remove the auxiliary button pad (make sure the rubber button pad comes with it) and set aside for later use. 14.
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty Assembly of Aftermarket Dash Kit (cont.) 4. Install the temperature and fan speed knobs as shown. Please make sure that the white line on the temperature control knob is centered at the top. 7. Install the black plastic gear as shown. Make sure the alignment mark on the gear is pointing at the gear attached to the temperature control knob. 5.
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty Assembly of Aftermarket Dash Kit (cont.) 10. Connect the (2) supplied ribbon cables to the bottom circuit board as shown. Make sure that the copper contacts on the ribbon cables are facing towards you. Once the cables are seated in the connector, lock them in place by pushing down on the locking tabs. 13.
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty Assembly of Aftermarket Dash Kit (cont.) This is the end of part three. Please continue to the next section to begin part four. 16. Install the middle circuit board housing as shown. Make sure that the top of the housing clears the auxiliary button pad during placement. 17. Using (4) of the supplied 6mm T10 screws, secure the housing to the panel as shown.
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty DIP Switches and Wiring Connections Set DIP switches that match your radio to the ON position Set all other DIP switches to the OFF position 1 2 3 4 DIP ON Alpine JVC Kenwood Clarion Pioneer/Other Sony Fusion 1 2 1&2 3 1, 2, & 3 4 1&4 Other = Advent, BOYO, Dual, Lightning Audio, Rockford Fosgate, Visteon 1.
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty VS41 Wiring PLEASE NOTE: Revision 1.0.6.1 of the VS41 is required for this application. If you are adding a front camera and two blind spot cameras, or any combination of the three, to the aftermarket radio, a VS41 is needed (sold separately). Follow the example below to make all inputs work accordingly through the reverse camera input on the aftermarket radio.
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty Steering Wheel Controls (Cont.) Optional Steering Wheel Control Programming If you wish to re-assign the SWC functions, utilize short press long press dual command functionality, or assign the programmable 12v output to a SWC button, the interface must be programmed in the specific order shown in the chart below.
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty Mounting the Aftermarket Radio Remove tab (LH & RH) for Double-DIN radio Install (LH-Side bracket shown) OR Attach included pocket to bottom of kit brackets Mount radio to brackets using supplied screws Mount radio to brackets using supplied screws Testing and Verification 1. 2. 3. 4. 5. Turn the ignition on.
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty RadioPRO App Use of the RadioPRO App in Ford allows you to do the following: • Configure User Interface Options such as: • Programmable 12v output (Red / White wire) behavior • Make vehicle settings selections such as: • Language • Temperature Units • Behavior of Front and Blind Spot Cameras (If Present) • Update Product Firmware • Read Firmware / Hardware Versions
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty RadioPRO App (cont.) Front and Blind Spot Camera Behavior (VS41 Required) If you’ve added front and / or blind spot cameras using the VS41, the behavior of these cameras can be setup using the RadioPRO PC application. Firmware Updates The RadioPRO app will also allow you to update the interface with new firmware as it becomes available. Please visit www. pac-audio.
RPK4-FD2201 Complete Radio Replacement with Integrated Climate Control Retention for select 2015-2018 Ford F150 and 2017-2018 Ford Super Duty Restoring Interface Factory Settings You can restore the interface to factory default settings by pressing and holding the programming button on the side of the module until LED 1 starts blinking red. Once the LED starts blinking red, release the button. You must release the button while the LED is blinking red in order to perform the reset.
