Manual

ManualsBrandsPace-Edwards ManualsCarBL Honda Ridgeline

HONDA RIDGELINE

INSTALLATION INSTRUCTIONS

Tools Required for Assembly.................................... 2

Before You Start ...................................................... 2

Packaging Contents ................................................ 2

STEP 1: Remove Contents from Box ..................... 2

STEP 2: Install Wiring Harness ............................... 3

STEP 3: Attach Rail Brackets & Rails to Canister ... 4

STEP 4: Install Cab End Rail Brackets.................... 5

STEP 5: Installing Cover in Truck Bed .................... 5

STEP 6: Lubricating the Rails.................................. 6

STEP 7: Connect the Electronics ............................ 6

STEP 8: Installing Drain Tubes................................ 6

STEP 9: Install Top Cover ....................................... 7

Release Handle Instructions .................................... 7

Helpful Maintenance Hints ...................................... 7

Warranty Statement.................................................. 8

BL_HONDA_RIDGELINE_0711

BL2060

(800) 338-3697

www.paceedwards.com

Pace Edwards Company

2400 Commercial Blvd.

Centralia WA 98531

ELECTRIC RETRACTABLE TRUCK BED COVER

TABLE OF CONTENTS

Summary of content (8 pages)

PAGE 1
ELECTRIC RETRACTABLE TRUCK BED COVER HONDA RIDGELINE INSTALLATION INSTRUCTIONS TABLE OF CONTENTS (800) 338-3697 www.paceedwards.com Pace Edwards Company 2400 Commercial Blvd. Centralia WA 98531 Tools Required for Assembly .................................... 2 Before You Start ...................................................... 2 Packaging Contents ................................................ 2 STEP 1: Remove Contents from Box ..................... 2 STEP 2: Install Wiring Harness ...............
PAGE 2
TOOLS REQUIRED FOR ASSEMBLY: 3/8” wrench or socket Razor box Knife #2 Phillips screwdriver #40 Torx wrench Wire Cutters #50 Torx wrench Drill w/ 3/4” taper drill or step drill bit BEFORE YOU START: Read the instructions carefully before you start. Due to the custom fit of this truck bed cover the installation will require a second person to help in running the wire and placing the canister in the truck bed.
PAGE 3
STEP 2: INSTALL WIRING HARNESS HARDWARE USED: (If the optional wire harness Part# BL1120 is used, you may want to tape it to the main harness to ease having to pull them through the bottom of bed separately). In the truck bed, remove the 2 factory bolts from both of the front upper tie down brackets using a #50 torx bit and set aside (for step 4). Remove the 6 factory bolts using a #40 torx bit that hold the front bed panel to the cab. Temporarily remove front bed panel.
PAGE 4
STEP 3: ATTACH RAIL BRACKET & RAILS TO THE CANISTER HARDWARE USED: Open the rail box along the length of the box; lift rails out to avoid scratching the rail surface on the package staples. REMOVE PROTECTIVE PAPER ON UNDERSIDE OF RAILS. THIS IS FOR PACKAGING PURPOSES ONLY. REAR RAIL BRACKET x 2 #8-32 x1/2” SCREWS x 4 Find the two rear rail bracket’s and four of the #8–32 X ½” countersunk screws in the hardware kit and attach them to each of the rails at the tailgate end.
PAGE 5
STEP 4: INSTALL CAB END RAIL BRACKETS & PREPARE BED HARDWARE USED: Find the two front rail brackets with rail mounting block attached to them in the hardware kit. Place the front rail bracket in front (mounting block up) of the upper tie down bracket and run factory bolts back in making sure the upper tie down bracket is exactly the way it was when removed. (Figure 4a) FRONT RAIL BRACKET x 2 FRONT UPPER TIE DOWN BRACKET FIG.
PAGE 6
STEP 6: LUBRICATING & PLACING THE SWEEP SEALS Locate the sweep seals (rubber weather strips) on the rails. Apply Pace Edwards’ UV Protectant (or 303 brand protectant) to a rag and wipe the underside of the sweep seal and the top of the wear strip. RAIL Extend the cover to the tailgate. Use an Allen wrench if needed to carefully draw out the sweep seal (seal should be angled outwards toward the cover – not rolled in toward the bed rail). (Fig.
PAGE 7
STEP 9: ATTACHING TOP COVER HARDWARE USED: Place the top cover on the canister opening and install the (2) Black Top Cover Screws into the attachment blocks mounted to the inside of the canister. Hold the top cover tight against the cab side of the box while tightening. BLACK TOP COVER SCREW x 2 (The top cover can be adjusted slightly to align evenly with the ribbed blanket) You have now completed the installation of the Bedlocker Electric hard tonneau cover.
PAGE 8
C O N G R AT U L AT I O N S ! On your purchase of a Pace Edwards Retractable Truck Bed Cover. We are confident that you will get many years of trouble free service from this accessory to your truck. Please take a moment to fill out the warranty registration form to activate warranty coverage of your truck bed cover. PACE EDWARDS PRODUCT WARRANTY PACE EDWARDS (hereinafter referred to as the MFG.