Manual

OPTIONAL HARDWARE
900 HARDWARE HEAVY-DUTY
2.
1. 4. 5. 6. 7.
3. 8.
800 HARDWARE MEDIUM-DUTY
7.
1. 2. 6.
4. 5.
3.
700 HARDWARE LIGHTWEIGHT
4.
3.
2. 5.
1.
1. TS900 Double Tom Stand
2. CB900 Straight/Boom Cymbal
Stand
3. SS900 Snare Stand
4. C900 Straight Cymbal Stand
5. HH900 3-Leg Hi-Hat
6. HH920 Rotating 2-Leg Hi-Hat
7. DT900Z White Sparkle/Zebra
Throne
8. DT900S Black Sparkle Throne
1. CB800 Straight/Boom Cymbal Stand
2. CS800 Straight Cymbal Stand
3. DT820X Tractor Throne
4. HH800-01 3-Leg Hi-Hat
5. SS800 Snare Stand
6. HH820 2-Leg Hi-Hat
7. DT800-04 Standard Throne
1. HH700 3-Leg Hi-Hat
2. CB700 Straight/Boom Cymbal Stand
3. SS700 Snare Stand
4. CS700 Straight Cymbal Stand
5. DT700 Throne
Bass Drum Assembly
Bass Drum Assembly
10" and 12" Tom Toms
Step 1: Set the bass drum shell on the side with the spurs (legs)
towards the top. Place the black “PDP” logo head over the shell. Center
the logo underneath the BDM (Bass Drum Mount Receiver) located on
the top of the bass drum.
Step 2: Place one of the bass drum hoops over the bass drum head
with the flat side of the hoop against the head.
Step 3: Slide 8 metal washers onto 8 longer tension rods . Then slide
the tension rod through 8 claw hooks .
Step 4: Position each claw hook over the bass drum hoop and thread the
tension rods into the lugs around the shell. Tighten by hand only. (You
will fully tighten and tune the drum later.)
Step 5: Set the shell right-side-up.
Step 6: Remove the plastic backing from the self-adhesive Velcro tape on
the bass drum pillow . Attach the pillow inside the bottom of the shell
with the adhesive. The pillow should be positioned towards the back of
the shell so that it will lightly touch the batter (clear) head when
assembled.
Step 7: Turn the drum on its side (black head down) with the pillow
towards the top. Place the clear batter head over the shell. Center the
logo underneath the BDM (Bass Drum Mount Receiver) located on the
top of the bass drum.
Step 8: Repeat steps 2 through 4 for the batter head.
Step 9: Set the shell right-side-up.
Step 10: By loosening the wing nut, angle the spurs so they face
slightly towards the front of the bass drum.
Step 11: Loosen the spur legs with the drum key and lower the legs
so that the front of the bass drum is lifted about one inch off the
ground. Tighten the spurs.
NOTE: For convenience, you may now want to tune your bass drum
before attaching the tom and pedal. Please refer to page 5 for tuning
guidelines.
Step 1: Insert the Double tom holder into the BDM receiver on top
of the bass drum.
Step 2: Loosen the wing screw on the bracket of the (10") tom tom
and slide it over the right tom arm on the left (from a right-handed
drummer’s perspective behind the kit - reverse if you play left-
handed). Take care that the tom arm does not touch the tom shell.
Tighten the wing screw on the tom bracket.
Step 3: Loosen the wing screw on the bracket of the (12") tom tom
Position it on the tom arm (reverse if you play left-handed). Take care
that the tom arm does not touch the tom shell. Tighten the wing screw
on the tom bracket.
NOTE: Don’t worry about the precise placement of the drums at this
point. You will arrange them all later.
Bass Drum Assembly
10" and 12" Tom Toms
D
B
C
H
G
F
E
B
A
K
O
P
F
H
G
C
B
D
C C
B
D
E
BDM Receiver
Bass Drum Assembly
K
O
P
BDM Receiver
D
B
C
D
F
G
Spurs
2
5
Package Contents
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
A Drum key (1)
B Bass Drum Heads (2)
(One Clear Batter & One Black Logo Resonant)
C Bass Drum Hoops (2)
D 18X22" Bass Drum Shell (1)
E Bass Drum Pillow (1)
F Claw Hooks (16)
G Bass Drum Tension Rods (16 + 2 spares)
H Metal Washers (48 + 4 spares)
I Lug Receivers (6 spares)
J Smaller Tension Rods For Toms (32 +2 spares)
K Bass Drum Mount Double Tom Holder (1)
L Single AC991 Tom Clamp (1)
M Floor Tom Drum Legs (6 - 2 Set Of 3 Legs Each)
N 7X8" Tom Tom (1 - Assembled)
O 8X10" Tom Tom (1 - Assembled)
P 9X12" Tom Tom (1 - Assembled)
Q 5X14" Snare Drum (1 - Assembled)
R 14" Floor Tom Drum Clear Heads (2)
S 12X14" Floor Tom Drum (1)
T 16" Floor Tom Drum Clear Heads (2)
U 14X16" Floor Tom Drum (1)
V PDP Drum Sticks (2)
Q
R
S
T
U
V
Steps to remove contents from
Box 1 of 2
1. Before removing anything from box 1 of 2, place the box in a
location where you will be able remove the contents of the
boxes.
2. Remove the top packet that holds the drum heads for the
bass drum
and the two floor tom drums. &
3. Remove the Bass Drum hoop.
4. Beneath the hoop, you will find fully assembled (12") and
(10") tom drums.
5. Remove all excess packing around the tom drums to ensure
easy removal.
6. Remove the top tom drum and then the bottom tom
drum. Place drums on a smooth and sturdy surface to prevent
damage your drums.
7. Remove the unassembled floor tom and place the drum on
a smooth and sturdy surface to prevent damage to your drum.
8. Remove the cardboard ring around the bass drum shell by
grabbing the cut-out handle and lifting upward.
9. Remove the bass drum pillow ,positioned along the side of
the bass drum shell.
10. With both hands, grasp each side of the bass drum shell ;
pull the bass drum shell upward to remove from the packaging.
Place the drum shell on a smooth and sturdy surface to prevent
damage to your drum.
11. Once the bass drum shell is removed from the box, lift up
the bottom cardboard insert to find the second bass drum
hoop.
12. Take this time to line up all the drums accordingly by size,
from smallest to largest.
13. Place the two large bass drum heads (clear/black) on top
of your bass drum shell.
14. Take the two (16") clear drum heads and place them on
top of the unassembled floor tom drum.
B
R
T
C
P
O
P
O
U
D
E
D
D
D
C
B
U
Steps to remove contents from
Box 2 of 2
15. Remove the top rectangular box containing the six legs for
the floor toms.
16. Place three legs next to the (16") floor tom from the
first box.The other three legs will be placed next to the other
floor tom once removed from this box.
17. Next you will find a long rectangular box that includes
drumsticks , claw hooks , washers , and tension rods
& that will be used during assembly.
18. Remove the box with the snare drum. Place the snare
drum on a smooth and sturdy surface to prevent damage to
your drum.
19. Remove and open the styrofoam box and place the smaller
AC991 tom clamp aside. Place the larger bass drum-
mounted double tom holder near the bass drum.
20. Under the snare drum box, you will find a smaller box with
another tom drum. Remove the drum from the box
and place the drum on a smooth and sturdy surface to prevent
damage to your drum.
21. Before removing the last drum from this packaging, be
sure to remove the styrofoam blocks to assure easy removal
from the
box.
22. Remove the last floor tom drum from the box just as you
did earlier for the bass drum.
23.Take this time to line up all the drums accordingly by size
from smallest to largest as you did earlier.
24. Take the three legs and place them next to the floor tom
drum just removed from the second box.
25. Take the last two remaining (14") clear drum heads and
place them on top of the floor tom drum just removed from
the second box.
M
M
U
V
F
H
G
J
Q
L
K
D
N
S
S
R
S
T
M
G
1
OPTIONAL RACK SYSTEM
Main Rack Package (PDSRPK05)
Combo Rack Package (PDSRCOMBO1)
A. PDCH1012 Closed Hi-Hat Arm B.
B. PDDB799 DogBone™ w/ Cymbal Arm
C. PDDB798 DogBone™ D.
D. PDCB0934 Cymbal Arm (Standard) A. E.
PDCB0934S Cymbal Arm (Short) C.
PDCB0978 Cymbal Boom Arm (7/8”)
E. DWSMRKDRKY Hi-Torque Drum key
F. DWSMRKFEET Rubber Feet (2-pack)
G. PDSRC15V 1.5”-V Clamp
H. DWSMRKC15A 1.5”-V Angle Adjustable Clamp F.
I. DWSMRKC15T 1.5”-1.5” T-Leg Clamp
J. DWSMRKC15K 1.5”-1.5” Rack Clamp
K. DWSMRKC15SV 1.5”-V Angle Adjustable Stacker
Clamp G. H. I. J.
L. DWSMRKC15AC 1.5” Accessory Clamp w/ Eyebolt
M. DWSMRKML15 1.5” Hinged Memory Lock
DWSMRKML10 1” Hinged Memory Lock
N. DWSMRKTTCA 1.5”-3/4” Tube Top Cymbal K. L. M. N.
Adapter
O. DWSMRKC15AS 1.5”-1.5” Hinged Angle
Stacker Clamp
P. DWSMRKC15VA 1.5”-V Accessory Clamp Q.
Q. DWSMRKC15S 1.5”-1.5” Angle Adjustable O. P. R.
Stacker Clamp
R. DWSMTA10 10.5 mm Tom Arm w/ Memory Lock
S. DWCPRKB42C 42” Stainless Steel Curved Bar
T. DWCPRKB24C 24” Stainless Steel Curved Bar
DWCPRKB12S 12” Stainless Steel Straight Bar
U. DWCPRKB24S 24” Stainless Steel Straight Bar S.
V. DWCPRKB36S 36” Stainless Steel Straight Bar
W. DWCPRKB42S 42” Stainless Steel Straight Bar V.
DWCPRKB72S 72” Stainless Steel Straight Bar W.
DWSMRKCAPS Tube End Caps (2-pack)
PDSRNPLV Pacific Nameplate Bar Level
T.
U.
Rack Accessories
6