Amplifier 1ch100 User manual October 10, 2004 Release: 1.30 1PA100 2002 by Pacific Laser Equipment Pacific Laser Equipment 1PA100User Manual Name: 1PA100UM Release: 1.30 Release Date: October 10, 2004 © 2001 by Pacific Laser Equipment PLEquipment, 3941S. BristolSt. Unit E, # 122, Santa Ana, CA. 92704,800 984-3482, Fax: 509-355-5155, info@plequipment.
Amplifier 1ch100 User manual October 10, 2004 Release: 1.30 1PA100 2002 by Pacific Laser Equipment Table of contents: 1. Introduction 1.1 Product description 1.2 Labels 1.3 Operation 1.4 Analog indicator 3 2. Block diagram 5 2.1 2.2 General diagram Power supplies diagram 3. Technical specs 6 4. Test and troubleshooting 7 5. Calibration 7 6. Addendum 8 7. O.E.M versions 9 PLEquipment, 3941S. BristolSt. Unit E, # 122, Santa Ana, CA.
Amplifier 1ch100 User manual October 10, 2004 Release: 1.30 1PA100 2002 by Pacific Laser Equipment 1.Introduction 1.1 Product description. The 1A100 is a unique piezo actuator driver with no position sensor processing electronics on board. It consists of a precision high voltage amplifier, AC power supply, insulation transformers, rectifiers, and voltage regulators. All this is compactly packaged in a 4-part aluminum case that has the surface connected to ground through the AC cord.
Amplifier 1ch100 October 10, 2004 1.2 User manual Release: 1.30 1PA100 2002 by Pacific Laser Equipment Labels. Rear panel label displays the power requirements and the unit serial number. Top cover the label shown bellow displays a “map” of the front panel controls and connectors. 1.3 Operation. Two operating modes can be selected from the front panel. Remote Controlled (RC) and Manually Controlled (MC).
Amplifier 1ch100 User manual October 10, 2004 Release: 1.30 1PA100 2002 by Pacific Laser Equipment Manual Operation: In MC mode the HV output can be controlled manually from 0 up to +150 VDC from the front panel DC- Offset Potentiometer. In this mode, the HV output is proportional to the number of turns on the DC offset potentiometer. 1.4 Analog indicator. Located on the front panel the voltage indicator can be use to read the approximate voltage applied to the piezo actuator.
Amplifier 1ch100 October 10, 2004 2.2 User manual Release: 1.30 1PA100 2002 by Pacific Laser Equipment Power supplies diagram 3.Technical specs Output voltage: 0V to +150V DC (positive polarity). Display: Analog voltage indicator. Analog input: 0 to 5V for 0 to nominal actuator expansion (pre-calibrated). Power out: 2.5W continuous, 5W peak. Dimensions: 5 x 3.21 x 1.85” Power requirements: 120V AC, 100mA.
Amplifier 1ch100 October 10, 2004 User manual Release: 1.30 1PA100 2002 by Pacific Laser Equipment Test and troubleshooting High voltage output Attention: The HV output can reach +150V. This is a dangerous voltage. Test in RC mode. At 5V analog input the indicator should read MAX. Fuse Check the main fuse inside the unit. When replacing it, use slow-blow 100mA. The fuse is located inside the box and access to it is fairly difficult. AC Power Make sure that the AC power used is always 120V.
Amplifier 1ch100 October 10, 2004 User manual Release: 1.30 1PA100 2002 by Pacific Laser Equipment Addendum Calibration graphs shown bellow for 0-5V control input. This data sheet has been carefullychecked and is believed to be reliable, however, no responsibility is assumed forpossible inaccuracies or omissions. Allspecifications are subjectto change without notice. PLEquipment, 3941S. BristolSt. Unit E, # 122, Santa Ana, CA. 92704,800 984-3482, Fax: 509-355-5155, info@plequipment.
Amplifier 1ch100 October 10, 2004 User manual Release: 1.30 1PA100 2002 by Pacific Laser Equipment 5. OEM version We are offering the OEM version as a stripped down version of the desktop model. These OEM version requires constant DC voltage up to 250V and the customer can specify the input voltage range. For volume orders custom designs are possible if they make economic sense. Special design amplifier with easy replacement connector. Special design, small layout amplifier.
