Installation Guide

Tools and supplies needed:
• Protective eye wear
• Measuring tape
• Utility knife
• Level
• Hand saw or circular saw/table saw
• Drill bit & jig saw (for cutting holes)
• Caulking gun for 10.3 oz. adhesive tubes
• Adhesive for PVC panels (Recommended adhesives: Loctite
®
Power
Grab
®
Ultimate (white formula), LIQUID NAILS
®
FUZE*IT
®
, Titebond
Titegrab Ultimate
TM
and Manus 75-AM HV)
• Silicone-based sealant for kitchen/bath (for wet environments)
• Optional: Matching trim
• Optional: Wood shims
Before you begin installation
Before starting, make sure all surfaces are clean, dry, smooth, and free
from dust, grease, wax, etc. Clean the back surface of the panels by
wiping with a clean cloth.
Perform a “dry layout” prior to applying adhesive. This will help you
visualize tile cuts and placement of tiles with similar designs. Some of the
stone-look tiles include color variations, lines, and cracks to emulate the
look of natural stone. Avoid placing tiles with similar or identical patterns
or texture next to each other. Measure walls, & check for level and square.
Depending on dimensions and room
construction, you may need to trim some
panels accordingly.
Installation in environments exposed to a
direct ow of water (shower, mud room or
garage) require a 1/8-inch bead of sealant
to be used in all tongue and groove
connections (image A). Add a bead of the
sealant along recently cut edges to be
placed into the corner. Repeat this process
on perpendicular tile also facing corner
(image B).
Cut Palisade tiles by scoring and snapping with a utility knife. (image C,
D). This method may require sanding the snapped edges.
H
You can also use standard wood
working tools like a table saw or
circular saw with a ne-tooth blade
to provide a clean, smooth cut
(image E). Use a 60-tooth blade or
higher. To ensure the base of the
saw does not scratch the surface
of the panel, we recommend
protecting the surface with blue
painter’s tape.
Cut panels for outlets and light switches. Measure and mark the borders
where the opening will be with a marker. Drill a 1/2-inch hole using a drill
in a corner of the cut-out section (image F). Use a jigsaw to cut the
remaining opening, following your tracing (image G).
Do not attach accessories like coat hooks, light ttings, mirrors, etc.
directly to the tiles. Drill holes through the tiles and use suitable anchors
to attach the accessories securely into the framing behind. Seal per
sealant instructions.
Installation onto drywall, OSB, plywood
or existing tile substrates
I
If you choose to nish the edges, we
recommend our matching trim for
both end pieces and inside corners.
We recommend using baseboard or
cove molding to nish the bottom
row, regardless of ooring material.
For both end trim pieces and corner
trims, install trim in appropriate
location prior to setting tile into trim
(image H).
Palisade tiles' unique interlocking
edges have a tongue and a groove
(image I). The tile's groove should
be facing up when installing.
If your project calls for Palisade tiles
starting at a oor, be sure the rst
row is straight and level. Determine
the desired height of your rst tile
row and snap or draw a level line at
that height for a reference line. Align
the tops of each panel in the rst row
to the snapped line (image J). It is
important that this starting row be
level and straight. If you are starting
with full tile, cut off the tongue or
use a matching J-trim along the
bottom edge.
To install your rst panel, begin with
bottom row. Make sure the rst panel
you intend to install ts properly and
is level. You may need to place a
temporary shim under each bottom
tile to hold them in place while the
adhesive sets (image K).
Apply adhesive to the back of the
tile. Carefully read and follow
adhesive manufacturer’s directions.
Apply a 1/4-inch bead in a typical
“M” or “W” pattern, and a bead
around the tile perimeter about
1-inch in (image L).
Apply the panel to the substrate by
pressing it into place. Apply even
pressure with your hands across the
entire panel. If necessary, use shims
or pins to hold panels in place until
the adhesive sets.
Wipe off excess adhesive. Use water
and a cloth. Clean off any adhesive
residue that is visible while it is still
wet. Do not allow this residue to dry
as it will be difcult to clean up when
dry and could damage the nish.
Connect the next tile by fully
inserting the tongue into the groove
(image M).
J
K
L
Repeat until bottom row is complete.
If installing in a corner, cut off the
ange facing the corner to allow a
plumb surface against the substrate.
Repeat this process on tile that abuts
the previous one also facing the
corner. Allow the adhesive on the
bottom row to set up so that all
subsequent rows remain level.
Determine what tile pattern you want
to use before starting the second row
M
P
(image N, O). Commonly-used options are running bond (vertical joints are
staggered) and stack bond (vertical joints line up).
Running Bond Stacked Bond
N
O
After the rst row has set up, apply the remaining tiles according to the
pattern or layout you desire. Use adhesive and methods described above
for remaining rows.
When installing the top row, install
as you have been until you get to
the last tile in the corner. If tiles butt
against your ceiling, when installing
the last tile, remove anges from
side (image P). Or use our matching
L trim. Lay tile into place. Apply
pressure to ensure tile is ush
with others. Use a recommended
silicone sealer (as previously
described) in joints to ensure a
water-tight installation, if applicable.
Installation of Last Tile In a Row
If you are using corner and/or L-trims for a Palisade shower kit installation,
the following information will show how to install the last, short tile at the
end of a row. Read and follow if your project looks like this. Optional
rubber gloves may make this task easier.
The challenge is to place the remaining tile section into the edge trim while
also getting the interlocking tile edges locked together (image Q).
First, install the inside corner trims
into each corner using adhesive.
Allow 24 hours for the adhesive to
cure. Make sure the corner trims
are oriented as in the image below.
Each inside corner trim piece has
a full and a partial channel. The
full channel will be against the
back wall.
The drawing below shows a top
cross-section view of facing
inside corners.
Q
Next, determine the length of the tile
section. Measure from the inside lip
of the previously installed tile to the
inside edge of the pre-installed trim.
See image at right for details. In this
case, the length to cut the nal tile in
the row is 4-3/4-inches (image R).
After cutting tile to length, apply
adhesive to the substrate, as shown
(image S).
Insert the cut tile edge into the L-trim
while holding the interlocking
joint-edge away from its mating tile.
Insert the cut end into the edge of
trim channel while holding other
edge up (image T).
Push the tile into the edge trim while
laying the tile down toward the
substrate. When pushed into the
trim entirely, the interlocking edges
will be exposed (image U).
Apply sealant to the interlocking edges if this installation is for a wet
environment.
The tile can now be manually pulled into place. Pull the tile toward the
interlocking joint (image V). If necessary, rubber gloves can be used to
increase grip friction with the surface of the tile. Keep pulling until the
interlocking joint is tight and in place (image W).
Use a damp rag or paper towel to clean off any sealant or adhesive that
may have been squeezed onto the tile surface.
Palisade Tile
Drywall or Other
Drywall or OtherDrywall or Other
Drywall or Other
Palisade TilePalisade Tile
Palisade Tile
Direction of Install
Tongue
Groove