Specification
Table Of Contents
- 1.1 SECTION INCLUDES
- 1.2 RELATED SECTIONS
- A. Section 06 11 00 - Wood Blocking: Blocking and shims attached to substrate to support, attached to a level plane.
- B. Section [______-____________]: Placement of special anchors or inserts for supporting panels.
- C. Section 07 92 00 - Joint Sealants: Silicone sealant for perimeter edge seal.
- D. Section [______-____________]: [Acoustic] partition system with head rails [attached to] [within] assembly.
- 1.3 REFERENCES
- A. ASTM E84 - Standard Test Method for Surface Burning Characteristics of Building Materials.
- B. ASTM E331 Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors and Curtain Walls by Uniform Static Air Pressure Difference
- C. ASTM G21 Resistance of Synthetic Polymeric Materials to Fungi
- D. CISCA (Ceilings & Interior Systems Contractors Association):
- 1.4 SUBMITTALS FOR REVIEW
- 1.5 QUALITY ASSURANCE
- 1.6 PROJECT CONDITIONS
- 1.7 DELIVERY, STORAGE AND HANDLING
- A. Section 01 66 00 for storage and handling of materials.
- B. Deliver materials in manufacturer’s original, unopened, undamaged containers with identification labels intact.
- C. Store cartons laid flat, protected from exposure to sun, high temperatures and humidity conditions as recommended by the manufacturer.
- 1.8 EXTRA MATERIALS
- 1.9 WARRANTY
- Part 2 Products
- 2.1 Wall PANELS
- A. Manufacturers:
- B. Material:
- C. Finish:
- 1. Tiles - Standard Colors: Wind Gust (53506, 53006), Wintry Mix (53508, 53008), Rain Cloud (53507, 53007), Frost Nickel (53502, 53002), Carrara Marble Matte (53510, 53010), Louvre Granite (53503, 53003), Hermitage Granite (53504, 53004), Prado Granit...
- 2. Planks – Standard Colors: Gray Oak (54000), Oak Mocha (54001), Natural Oak (54002)
- 3. ACCESSORIES
- D. Edge Moldings: Trims available consult manufacturer.
- E. Adhesive: Loctite Power Grab Ultimate, Manus 75-AM HV
- F. Include the notched trowel below if panels will be glued with a troweled adhesive.
- G. Tools: Site-cutting tools, [and notched trowel] for installing panels.
- 2.1 Wall PANELS
- Part 3 Execution
- 3.1 EXAMINATION
- 3.2 INSTALLATION
- A. Install assembly in accordance with manufacturer's instructions and as supplemented in this section.
- B. Cutting Panels: Using a table saw or circular saw for cuts, and jig saw for irregular cuts like around wall outlets.
- C. Surface Mounting:
- 1. Prepare substrate surface by cleaning properly. (free of dust and organic material that may impede adhesion)
- 2. Apply adhesive to substrate using a notched trowel or tube adhesive with proper coverage.
- 3. Install full panels, working across the room.
- 4. Overlap tongue and groove tiles.
- 5. Once completed, firmly press all wall panels to ensure proper adhesive bond.
- D. Perimeter Molding:
- 3.3 SCHEDULE
Acoustic Ceiling Products (ACP)
Palisade Wall PVC Panels Section 09 51 01
February 2021 PVC PANELS
Page 4
1. Prepare substrate surface by cleaning properly. (free of dust and organic material
that may impede adhesion)
2. Apply adhesive to substrate using a notched trowel or tube adhesive with proper
coverage.
3. Install full panels, working across the room.
4. Overlap tongue and groove tiles.
5. Once completed, firmly press all wall panels to ensure proper adhesive bond.
D. Perimeter Molding:
1. Install edge trim at the ends of your wall if desired.
2. Use single piece longest practical lengths.
3.3 SCHEDULE
END OF SECTION