Use and Care Manual

IMPORTANT
Please read these instructions carefully before you start to assemble this product .
Please carry out the steps in the order set out in these instructions.
Keep these instructions in a safe place for future reference.
Safety advice
For safety purposes we strongly recommend the product to be assembled by at least two people.
Some parts may have sharp edges. Please be careful when handling components. Always wear gloves, eye
protection, and long sleeves when assembling or performing any maintenance on your product.
Do not attempt to assemble the product in windy or wet conditions.
Do not attempt to assemble the product if you are tired, have taken drugs, medications or alcohol, or if you are
prone to dizzy spells.
Dispose of all plastic bags safely - keep them away from children's reach.
Keep children away from the assembly area.
When using a stepladder or power tools, make sure that you are following the manufacturer's safety advice.
Do not climb or stand on the roof.
Do not hang or lay on the profiles.
Heavy articles should not be leaned against the poles.
Keep roof and gutters clear of snow, dirt & leaves.
Heavy snow load on the roof can make it unsafe to stand below or nearby.
If color was scratched during assembly it can be fixed.
Cleaning instructions
In order to clean the product, use a mild detergent solution and rinse with
cold clean water.
Do not use acetone, abrasive cleaners, or other special detergents to clean the panels.
Clean the product once assembly is complete.
Before starting assembly
Choose your site carefully before beginning assembly.
The ground surface must be perfectly flat and leveled and have a solid base such as concrete, asphalt, deck etc.
Sort the parts and check against the content parts list.
Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.
Please consult your local authorities if any permits are required prior to constructing the product.
Tools & Equipment
T001 (Supplied)
Required for assembly (in addition to the previously depicted tools)
1. 8 wooden beams, minimum 6' long (1.8 m)
2. Concrete
3. Digging equipment, compatible with the soil type and required measurements
4. High step ladder, minimum of 8 rungs (8' / 2.4 m)
During Assembly
MWhen encountering the information icon, please refer to the relevant assembly step
for additional comments and assistance.
Attention
Please use both assembly instructions (Arizona Wave / Breeze + Arizona EZ Link) in order to assemble the product
Please note there are 2 types of glazing in addition to 2 assembly options: Wings / Arch, as shown in the first page.
Make sure you follow the pages showing the product you chose to assemble.
Follow the main instructions of the Arizona Wave / Breeze after completing the relevant steps in these instructions.
During assembly use a soft surface below the parts to avoid scratches and damages.
Please make sure you install the panels with the UV protected side
out (marked with "THIS SIDE OUT") and remove the sticker as panels are in place.
Wing Parking:
Step 1: Dig two (2) holes according to the specified measurements and make sure the bottom is well tightened.
Plan ahead according to the placement of the parking as shown in the drawing. Make sure the pits'walls are at a
90°.
If the ground is sandy and digging proper holes is impossible, please consult a local expert / constructor.
Step 2: Please use wooden beams (not supplied) to set and hold the aluminum poles in place, make sure the
profiles are set at a depth of 19.6" (50 cm) in accordance with step #4 in the Arizona Wave/Breeze assembly
instructions.
The aluminum poles must be leveled in all directions.
*Carry out steps 1-4 in the Arizona Wave / Breeze assembly instructions, prior to carrying out this step.
Step 3: Please note and make sure the concrete casting reaches the line that was marked on the profile at the
previous steps.
* Please wait for the concrete to be fully set and dry, in accordance with the manufacturer's instructions and
depending on the weather conditions, before continuing with the assembly!
Step 4: Carry out steps 7-8 in the Arizona Wave / Breeze assembly instructions, prior to carrying out this step.
Please note the profile's direction.
Step 5: Carry out steps 10-17 in the Arizona Wave / Breeze assembly instructions, prior to carrying out this step.
Step 6: Carry out steps 18-19 in the Arizona Wave / Breeze assembly instructions, prior to carrying out this step.
Step 7: Carry out steps 20-23 in the Arizona Wave / Breeze assembly instructions, prior to carrying out this step.
For Arizona Breeze -WINGS: After this step, proceed with Arizona Breeze assembly instructions.
Step 8: Carry out steps 20-25 in the Arizona Wave assembly instructions, prior to carrying out this step.
Step 9: Carry out steps 27-29 in the Arizona Wave assembly instructions, prior to carrying out this step.
Step 10: Lay out all the panels and make sure they overlap, move one set of panels at a time in order to connect
them to the roof with the supplied screws.
After this step, proceed with Arizona Wave assembly instructions.
Tighten all screws at the end of assembly.
Arch Parking:
Step 11: Dig (4) holes according to the specified measurements and make sure the bottom is well tightened.
Plan ahead according to the placement of the parking as shown in the drawing. Make sure the pits'walls are
at a 90°.
If the ground is sandy and digging proper holes is impossible, please consult a local expert / constructor.
Step 12: Please use wooden beams (not supplied) to set and hold the aluminum poles in place, make sure the
profiles are set at a depth of 19.6" (50 cm) in accordance with step #4 in the Arizona Wave/Breeze assembly
instructions.
The aluminum poles must be leveled in all directions.
Step 14: Please note and make sure the concrete casting reaches the line that was marked
on the profile at the previous steps.
* Please wait for the concrete to be fully set and dry, in accordance with the manufacturer's instructions
and depending on the weather conditions, before continuing with the assembly!
Step 15: Carry out steps 7-25 in the Arizona Breeze assembly instructions, prior to carrying out this step.
Step 17: Carry out step 32 in the Arizona Breeze assembly instructions, prior to carrying out this step.
Step 23: In order to be able to insert the sealing strips, perform gradually: panel + sealing strip.
Step 25: After this step, proceed with Arizona Breeze assembly instructions.
Step 26: Carry out steps 7-24 in the Arizona Wave assembly instructions, prior to carrying out this step.
Step 30: Carry out steps 27-29 in the Arizona Breeze assembly instructions, prior to carrying out this step.
Step 31: Lay out all the panels and make sure they overlap, move one set of panels at a time in order to connect
them to the roof with the supplied screws.
After this step, proceed with Arizona Wave assembly instructions.
Tighten all screws at the end of assembly.
Note:
Anchoring this product to the ground is essential to its stability and rigidity.
It is required to complete this stage in order for your warranty to be valid.