Remote Operation Panel AK-HRP931P Before attempting to connect, operate or adjust this product, please read these instructions completely.
Safety precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Contents Overview ......................................................................................................................................................................... 3 Accessories ..................................................................................................................................................................... 3 Operating precautions ........................................................................................................................
Operating precautions ≥ The panel’s power is supplied from the camera control unit (AK-HCU931P). ≥ Handle the panel carefully. Dropping the panel or subjecting it to strong impact may cause malfunctioning and failures. ≥ Operate the panel within a temperature range of 32 °F to 104 °F (0 °C to 40 °C). Operation in locations below 32 °F or above 104 °F may adversely affect the internal parts. ≥ Turn off the power before connecting or disconnecting the cables. ≥ Do not use the ROP outdoors.
Parts and their functions ROP operation panel When any of the panel switches is pressed, the buzzer sounds. However, the buzzer does not sound when the panel's ON switch lamp is off or when BUZZ OFF has been selected on the FUNC menu. 1 3 : 2 4 8 5 9 6 4 VF power OFF switch [VF OFF] This is the camera VF power switch for exercising remote control from the panel. It lights when the switch is in the ON position.
Parts and their functions 2 Auto black balance switch [AUTO BLACK] This is used to automatically adjust the black balance. Lighted: This indicates that the automatic black balance adjustment has started. Flashing: This indicates that the automatic black balance adjustment ended without being completed. Off: This indicates that the automatic black balance adjustment was completed correctly. 3 Auto setup switch [AUTO SET UP] This is used to perform auto setup. The setup status is output to PM each time.
Parts and their functions 1 5600K switch [5600K MODE] This is used to change the amplification rate of the GBR signals by an electrical circuit to achieve a white balance that corresponds to the color temperature of 5600K. When it is pressed, the B video signal is attenuated by approximately -6 dB, the R video signal is boosted by approximately 3 dB, and the G video signal is not attenuated. Select this switch setting for shooting under a 5600K light source or shooting outdoors.
Parts and their functions VPAR: Vertical parabola correction This is used to correct the coloring of black screen images in the vertical direction in the range of –100 to 100. When the numerical setting is incremented, the video level at the top and bottom of the screen is increased. 2 White shading control switch [WHITE SHADING CONTROL] This is used to correct the white shading.
Parts and their functions 9 Flare control switch [FLARE CONTROL] This is selected to change the amount of flare correction. When it is selected, its lamp lights. RFLR 10 GFLR 49 BFLR 0 RFLR, GFLR, BFLR These adjust the R, G or B flare in the range of –100 to +100, and at 0 the flare correction operation is turned off. : Gamma curve control switch [GAMMA CONTROL] This is selected to adjust the gamma correction. When it is selected, its lamp lights.
Parts and their functions –CLP: Detail edge undershoot clip This is used to limit the length of the undershoot parts of the detail edge components. CRSP: Skin tone detail crisp This is used to remove the very faint noise components below the level set from the skin tone detail components. +KNE: Detail edge overshoot knee This function applies the knee to the detail edge overshoot parts. = SDTV detail control switches [SD.
Parts and their functions +CLP: Detail edge overshoot clip This is used to limit the length of the overshoot parts of the detail edge components. –CLP: Detail edge undershoot clip This is used to limit the length of the undershoot parts of the detail edge components. KNEE: Detail edge knee This function applies the knee to the detail edge parts. CRM: Chroma detail This function boosts the detail in the high chroma saturation.
Parts and their functions DCLK: Down-conversion link This is used to decide whether to go with the downconversion system control based on the AUX external input or set the down-conversion independently. UCLK: Up-conversion link This is used to decide whether to go with the upconversion system control that is linked to the downconversion system or set the up-conversion independently. PATHO: Pathological pattern output This is used to forcibly output the pathological pattern.
Parts and their functions POWER (FAN): Fan power switch This is used to set the power of the camera head’s fan to ON, OFF, or AUTO. FILTER ND CAP 100 6.3 1.6 SCENE FILE C SPEED (FAN): Fan speed This is used to set the speed of the camera head’s fan. G 1 2 3 4 5 6 7 8 3.2 STORE GAIN G R CC HEAD 25 4.3 6.
Parts and their functions Calling scene file data 1. From among the 1 to 8 scene file switches, press the number of the switch that corresponds to the scene file which is to be called and light its lamp. 2. The scene file is now read. The data read from the scene file is input into the current file and then output. 3. When the scene file is read, the data left in the current file until that moment is temporarily saved. The lamp of the scene file switch remains lighted even after the data has been called.
Parts and their functions G R, G, B gain controls [R, G, B GAIN] These are used for the red (R), green (G) and blue (B) adjustments of the white balance. When the auto white balance can be performed and the R, G or B gain control is turned, the gain control value on the LCD display changes. H R, G, B black controls [R, G, B FLARE] Whether these controls are to be used to adjust the flare or pedestal can be set on the menu. They are used for the red (R), green (G) and blue (B) black adjustments.
Parts and their functions ROP connector panel X CCU connector The camera control unit (CCU) is connected here. Y RCP connector The remote control panel (RCP) is connected here. PREVIEW RCP Y CCU X Z Z Preview control connector [PREVIEW] This is the output connector which is used for previewing. When the joystick is pushed in, the contact information is output. Connections Connections of the system components 1.
External dimension drawings RCP CCU PREVIEW CAMERA NO. ROP ON HEAD ON VFPW SD CARD CLOSE BAR TEST AUTO WHITE BLACK SET UP MODE FLARE BLK GAMMA AUTO KNEE ON OFF GAMMA ON OFF 5600K KNEE OFF ALARM CHARACTER RST OPT FAN CABLE 60Hz WHITE MATRIX HD. DTL SD. DTL CLIP OFF ON OFF OFF CONTROL BLACK WHITE SHADING R G PED FLAME GAMMA GAIN UNDO FUNC B WHITE CLIP KNEE FILTER ND 16-1/2 inch (419 mm) BLK GAMMA HD. DTL SD.
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000 EASTERN ZONE: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621 Southeast Region: 1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835 Central Region: 1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200 WESTERN ZONE: 3330 Cahuenga Blvd W.