Datasheet

ManualsBrandsPANASONIC ManualsPush Actuated Switches & ButtonsMicroswitch 30 Vdc 0.1 A 1 x On/(On) momentary 1 pc(s)

ASQ1

ORDERING INFORMATION

OPERATION CONCEPT DIAGRAM (reference)

ULTRA-LONG STROKE,

HIGH CONTACT RELIABILITY

SEALED SWITCHES

(SAME SIZE AS J TYPE)

TURQUOISE STROKE

SWITCHES

(mm)

FEATURES

1. Same size as J type with ultra-long

stroke. For pin plunger type, it

maintains an ultra-long stroke O.T.

(Over Travel) with over 2.2 mm on the

NO side and over 2.5 mm on the NC

side. Variations in operation can be

absorbed.

2. Since contact pressure does not

depend on the operation stroke, the

range of possible use over the entire

stroke is greatly increased.

(Please refer to operation concept

diagram.)

3. High contact reliability to support

low level switching loads

High contact reliability is maintained with

gold plating on both sides of sliding

contact.

4. Highly effective sealing for

resistance against adverse

environments

Immersion protection type

• JIS C0920 (water-resistance

experiments for electrical machines and

protection rating against incursion of

solid substances)

• JIS D0203 (method for testing moisture

resistance and water resistance in

automotive components)

IP67

• IEC529 (rating for outer shell protection)

5. Silent operation

With sliding contact construction there is

no operation noise.

6. Direct operation possible from

lateral direction with pin plunger

(lever-less operation allows space

savings)

7. Contains no harmful substances

(mercury, lead, hexivalent chromium,

cadmium)

TYPICAL APPLICATIONS

1. Automobiles (detection of door

opening and closing and shift lever

position, etc.)

2. Household appliances (propane

stoves, vacuum cleaners, air

conditioners, washing machines, etc.)

13.3

9.6

5.4

RoHS Directive compatibility information

http://www.mew.co.jp/ac/e/environment/

Type of switch

ASQ1: Turquoise

stroke

switch

Size of mounting hole

3 mm standard type

3 mm without boss type

Right side pin type

Left side pin type

Right 2 boss type

Left 2 boss type

Te r minal

Wire leads right side type (NC and NO type only)

Wire leads left side type (NC and NO type only)

Solder terminal

PC board terminal

Wire leads (bottom type)

PC right angle terminal

PC left angle terminal

Contact form

SPDT

SPST-NC

(wire lead type only)

SPST-NO

(wire lead type only)

Actuator

Pin plunger

Leaf lever

Simulated leaf

lever

Ex. ASQ1

Remark: Not every combination is available. Please refer to the following table, “PRODUCT TYPES”.

Contact form: terminal type

Stroke

Operation load

Contact pressure

Range of possible use

Operation

load

NC side

NO side

RP (NC)

OP (NC)

OT (NC)

OT (NO)

TTP

OP (NO)

RP (NO)

Standard (mounting boss and

hole center diameter or standoff)

NC side

NO side

(OFF)

CONTACT

ARRANGEMENT

1. SPDT

COM NO NC

2. SPST-NC

(Wire leads type only)

3. SPST-NO

(Wire leads type only)

COM NC COM NO

Summary of content (10 pages)

PAGE 1
ASQ1 13.3 ULTRA-LONG STROKE, HIGH CONTACT RELIABILITY SEALED SWITCHES (SAME SIZE AS J TYPE) TURQUOISE STROKE SWITCHES 2. Since contact pressure does not depend on the operation stroke, the range of possible use over the entire stroke is greatly increased. (Please refer to operation concept diagram.) 3. High contact reliability to support low level switching loads High contact reliability is maintained with gold plating on both sides of sliding contact. 4.
PAGE 2
ASQ1 APPLICABLE CURRENT RANGE (reference) 100mA Applicable range 1mA 0 DC 5V 30V PRODUCT TYPES 1. Terminal type (Mounting hole: 3mm standard type/3mm without boss type/2 boss type/Side pin type) Mounting hole: 3mm standard type Actuator Operating force Max. Solder terminal Pin plunger Leaf lever Simulated leaf lever 1.5N 1.7N 1.
PAGE 3
ASQ1 4. Characteristics Item Electrical switching life 5 V DC 1 mA (resistive load) 16 V DC 50 mA (resistive load) 30 V DC 100 mA (resistive load) Vibration resistance (malfunction vibration resistance) Shock resistance (malfunction shock resistance) Vibration resistance endurance Terminal strength Heat resistance Cold resistance Humidity resistance High-temperature, high-humidity resistance Thermal shock resistance Water resistance Specifications Min. 5 × 105 Switching frequency: 20 times/min.
PAGE 4
ASQ1 DIMENSIONS mm General tolerance: ±0.25 1. Terminal type: Mounting hole 3mm, standard type Pin plunger Operating Force (max. O.F.) From mounting boss Free and hole center line Position (max. F.P.) From standoff Operating From mounting boss Position on and hole center line NC side O.P. (N.C.) From standoff FP 9.2 MAX. RP (NC) 8.8±0.3 OP (NC) 8.7±0.3 RP (NO) 8.5±0.3 OP (NO) 8.4±0.3 TTP (5.9) C0.3 8.4±0.2 13.3±0.15 5.4±0.15 5.4 2.7 1.9 dia. 3.0 TTP (10.1) RP (NO) 12.7±0.3 OP (NO) 12.6±0.
PAGE 5
ASQ1 Simulated leaf lever C 0. 3 Operating Force (max. O.F.) From mounting boss Free and hole center line Position (max. F.P.) From standoff 2.8 13.3±0.15 R2.0 FP 14.4 MAX. RP (NC) 12.9±0.5 OP (NC) 12.5±0.5 RP (NO) 12.4±0.5 OP (NO) 12.0±0.5 TTP (8.7) mm General tolerance: ±0.25 1.9dia. 15.0 Operating From mounting boss Position on and hole center line NC side O.P. (N.C.) From standoff 8.4±0.2 5.4±0.15 3.3 5.4 2.7 °) (18 Operating From mounting boss Position on and hole center line NO side O.P.
PAGE 6
.0 2-3 +0.3 5.1 5.9 3 0. C +0.3 3.0−0.2 3.7 4.2 5.1 5.9 RP (NC) 8.8±0.3 OP (NC) 8.7±0.3 RP (NO) 8.5±0.3 OP (NO) 8.4±0.3 8.3±0.1 1.2 2.0 4.53±0.15 8.3±0.1 1.2 2.0 4.53±0.15 1.5 0.4 TTP (5.9) FP 9.2 MAX. 4.53±0.15 3.7 4.2 TTP (5.9) RP (NC) 8.8±0.3 OP (NC) 8.7±0.3 RP (NO) 8.5±0.3 OP (NO) 8.4±0.3 1.5 0.4 1.2 2.0 1.5 0.4 . dia 3.0−0.2 + −00 .1 FP 9.2 MAX. FP 13.4 MAX. RP (NC) 13.0±0.3 OP (NC) 12.9±0.3 RP (NO) 12.7±0.3 OP (NO) 12.6±0.3 TTP (10.1) +0.3 3.0−0.2 3.7 4.2 2.6±0.
PAGE 7
ASQ1 3. Angle terminal type (3 mm standard type only) Right type mm General tolerance: ±0.25 C 5.08±0.15 2 0. 5.08±0.15 0.9 NO NC C RP (NC) 8.8±0.3 OP (NC) 8.7±0.3 RP (NO) 8.5±0.3 OP (NO) 8.4±0.3 0. 3 COM 13.3±0.15 8.4±0.2 5.4 5.4±0.15 2.7 1.9 dia. 3.7 4.2 6.0±0.3 3.0 −0 5.1 5.9 +0.1 TTP (5.9) FP 9.2 MAX. 3.2±0.1 4.1 2.0 0.4 3.0 + − 0 0.1 dia . 8.3±0.1 3.1±0.4 Left type (3 mm standard type only) C 0. 3 COM C 0.9 NO 2 0. NC 5.08±0.15 RP (NC) 8.8±0.3 OP (NC) 8.7±0.
PAGE 8
ASQ1 FP 9.2 MAX. OP (NC) 8.7±0.3 OP (NO) 8.4±0.3 TTP (5.9) 4. Wire leads bottom type: Mounting hole 3mm, standard type mm General tolerance: ±0.25 8.4±0.2 C 0.3 13.3 5.4±0.15 5.4 2.7 1.9 dia. 3.2±0.1 3.0+0.1 −0 5.1 5.9 3.7 8.3±0.1 3.0+0 −0.1 dia. 4.3 3.2 R 0.3 4.2 R 0.3 2.2 3.6 2.6 1.4 dia. 300±10 5.0±2 ∗ Wire lead thickness : Wire lead color : : : 0.3mm2 COM ···· Black NC ······· Red NO ······· White FP 9.2 MAX. OP (NC) 8.7±0.3 OP (NO) 8.4±0.3 TTP (5.9) 5.
PAGE 9
ASQ1 6. Wire leads left side type: Mounting hole 3mm, standard type mm General tolerance: ±0.25 FP 9.2 MAX. OP (NC) 8.7±0.3 OP (NO) 8.4±0.3 TTP (5.9) R 0.5 8.4±0.2 5.4±0.15 1.9 dia. C 0.3 13.3 5.4 2.7 3.2±0.1 3.0+0.1 −0 5.1 5.9 R 0.5 1.4 dia. 3.7 8.3±0.1 4.5 4.3 5.0±2 R 0.5 5.2 3.0+0 −0.1 dia. 300±10 ∗ Wire lead thickness : Wire lead color : : : 2.4 0.3mm2 COM ···· Black NC ······· Red NO ······· White NOTES 1.
PAGE 10
ASQ1 6. Oil-proof and chemical-proof characteristics The rubber cap swells when exposed to oil and chemicals. The extent of swelling will vary widely depending on the type and amount of oil and chemicals. Check with the actual oil or chemicals used. In particular, be aware that solvents such as freon, chlorine, and toluene cannot be used. 7.