User manual

ManualsBrandsPANASONIC ManualsPhotoelectric SensorsCX411PZ

()

Stability indicator

(Green) (Note 1)

()

Lights up under the

stable Light condition

or the stable Dark

condition

Operation indicator

(Orange) (Note 2)

()

Lights up when the

sensing output is ON

Sensitivity adjuster

(Note 1)

Sensing range becomes

longer when turned

clockwise

Operation mode

switch (Note 1)

()

L: Light-ON

D: Dark-ON

Color code / Connector pin No.

of the connector type

100mA max.

Sensor circuit

(Brown/1)

(Black/4)

Output (Note)

(Blue/3) 0V

Users’ circuitInternal circuit

Load

–

12 to 24V DC

±10%

Not connected

Output (Note)

Connector pin position of

the M8 connector type

Connector pin position of

the M12 pigtailed type

Not connected

Output (Note)

Color code / Connector pin No.

of the connector type

Not connected

Output (Note)

Connector pin position of

the M8 connector type

Connector pin position of

the M12 pigtailed type

100mA max.

Sensor circuit

(Brown/1) +V

(Black/4)

Output

(Note)

(Blue/3) 0V

Users’ circuitInternal circuit

Load

–

12 to 24V DC

±10%

Not connected

Output (Note)

INSTRUCTION MANUAL

Compact Size Photoelectric Sensor

Thank you very much for using SUNX products. Please

read this Instruction Manual carefully and thoroughly for

the correct and optimum use of this product. Kindly keep

this manual in a convenient place for quick reference.

SPECIFICATIONS

CAUTIONS

䢇 Make sure to carry out wiring in the power supply

off condition.

䢇

Take care that wrong wiring will damage the sensor.

䢇

Verify that the supply voltage variation is within the rating.

䢇

If power is supplied from a commercial switching regu-

lator, ensure that the frame ground (F.G.) terminal of

the power supply is connected to an actual ground.

䢇 In case noise generating equipment (switching

regulator, inverter motor, etc.) is used in the vicin-

ity of this product, connect the frame ground (F.G.)

terminal of the equipment to an actual ground.

䢇 Do not run the wires together with high-voltage

lines or power lines or put them in the same race-

way. This can cause malfunction due to induction.

Notes:1) The model No. with suffix ‘-J’ is the M12 pigtailed type, ‘-Z’ is the M8 connector type.

(e.g.) M12 pigtailed type: CX-411-J, M8 connector type: CX-411-Z

Use the connection cables as shown below. (Two sets are required for the thru-beam type sensor.)

CX-400 Series

Amplifier Built-in

2) The retroreflective type sensor with polarizing filters may not stably detect

specular or glossy objects through transparent film since light is polarized

by the transparent film.

For details, refer to ‘m RETROREFLECTIVE TYPE SENSOR WITH

POLARIZING FILTERS’.

3) The sensing range and the sensing object for the retroreflective type sen-

sor is specified for the RF-230 reflector.

Further, make sure to mount the sensor and the reflector 0.1m, or more,

away from each other.

4) The sensing range of the diffuse reflective type sensor and the narrow-

view reflective type sensor is specified for white non-glossy paper

(200 × 200mm) as the object.

5) By mounting interference prevention filters (PF-CX4-

), two sets of the

sensor can be mounted close together.

For details, refer to ‘.INTERFERENCE PREVENTION FILTER (OPTIONAL)’.

䢇 Operation mode switch

Reflector cannot be placed

in this range

Actual sensing range

of the sensor

Setting range of

the reflector

ReflectorReflectorSensor

0.1m

䢇 Do not use during the initial transient time (50ms)

after the power supply is switched on.

䢇 This sensor is suitable for indoor use only.

䢇 Extension up to total 100m, or less, is possible with

0.3mm

, or more, cable. However, in order to re-

duce noise, make the wiring as short as possible.

䢇 Make sure that stress by forcible bend or pulling is

not applied directly to the sensor cable joint.

䢇 Do not use this sensor in places having excessive

vapor, dust, etc., or where it may come in direct

contact with water, or corrosive gas.

䢇 Take care that the sensor does not come in direct

contact with water, oil, grease, or organic solvents,

such as, thinner, etc.

The model No. of retroreflective type sensor with the suffix ‘-Y’ is the sensor without the RF-230 reflector.

(e.g.) CX-491-Y

Type Model No. Cable length

2-core type

CN-22-C2 2m

CN-22-C5 5m

4-core type

CN-24-C2 2m

CN-24-C5 5m

Type Model No. Cable length

Straight type

CN-24A-C2 2m

CN-24A-C5 5m

Elbow type

CN-24AL-C2 2m

CN-24AL-C5 5m

Notes:1)

Not incorporated on the thru-beam type sensor emitter.

It is the power indicator for the thru-beam type sensor emitter.

ADJUSTMENTS

䢇 Top face

Note: The emitter of thru-beam type sensor does not incorporate the output.

Symbols... D : Reverse supply polarity protection diode

D : Surge absorption zener diode

Tr : PNP output transistor

Note: The emitter of thru-beam type sensor does not incorporate the output.

䢇 PNP output type

Symbols... D : Reverse supply polarity protection diode

D : Surge absorption zener diode

Tr : NPN output transistor

I/O CIRCUIT DIAGRAMS

䢇 NPN output type

䢇

Never use this product as a sens-

ing device for personnel protection.

䢇 In case of using sensing devices

for personnel protection, use prod-

ucts which meet standards, such

as OSHA, ANSI or IEC etc., for per-

sonnel protection applicable in

each region or country.

WARNING

Light-ON mode is obtained when

the operation mode switch (located

on the receiver) is turned fully clock-

wise (L side).

Dark-ON mode is obtained when the

operation mode switch (located on

the receiver) is turned fully counter-

clockwise (D side).

Operation mode switch

Description

Mounting

bracket

(optional)

M3 (length: 12mm)

screws

MOUNTING

䢇 The tightening torque should be 0.5N·m or less.

Typ e

Model No. NPN output

Item

(

Note 1) PNP output

Sensing range

Sensing object

Repeatability

(perpendicular to sensing axis)

Supply voltage

Current consumption

Output

Output operation

Short-circuit protection

Response time

Operation indicator

Stability indicator

Power indicator

Sensitivity adjuster

Automatic interference

prevention function

Protection

Ambient temperature

Ambient humidity

Emitting element

Material

Cable

Weight

Accessory

Thru-beam

Retroreflective type sensor

Diffuse reflective Narrow-view

with polarizing filters (Note 2)

Short sensing range Long sensing range

reflective

CX-411 CX-491 CX-421 CX-422 CX-423

CX-411-P CX-491-P CX-421-P CX-422-P CX-423-P

10m 3m (Note 3) 300mm (Note 4) 800mm (Note 4)

70 to 200mm (Note 4)



12mm or more Opaque, translucent or

opaque object transparent object

0.5mm or less 1mm or less 0.5mm or less

12 to 24V DC ±10%

Ripple P-P 10% or less

Emitter: 20mA or less

20mA or less 25mA or less 20mA or less

Receiver: 20mA or less

NPN open-collector transistor PNP open-collector transistor

· Maximum sink current: 100mA · Maximum source current: 100mA

Applied voltage: 30V DC or less (between output and 0V)

Applied voltage: 30V DC or less (between output and

Residual voltage: 1V or less (at 100mA sink current)

Residual voltage: 1V or less (at 100mA source current)

0.4V or less (at 16mA sink current) 0.4V or less (at 16mA source current)

Switchable either Light-ON or Dark-ON

Incorporated

1ms or less

Orange LED (lights up when the output is ON), thru-beam type sensor: located on the receiver

Green LED (lights up under stable light received condition or stable dark condition)

thru-beam type sensor: located on the receiver

––

Continuously variable adjuster

––

(Note 5) Incorporated (Two units of sensors can be mounted closely.)

IP67 (IEC)

–25 to +55

˚C

(No dew condensation or icing allowed), Storage: –30 to +70

˚C

35 to 85% RH, Storage: 35 to 85% RH

Red LED (modulated) Infrared LED (modulated)

Red LED (modulated)

Enclosure: PBT, Lens: Acrylic, Indicator cover: Acrylic

0.2mm

3-core (thru-beam type sensor emitter: 2-core) cabtype cable, 2m long

Emitter: 45g approx.

50g approx.

Receiver: 50g approx.

––

RF-230 (Reflector): 1 No.

––

Opaque, translucent or trans-

parent object (Min. sensing

object



0.5mm copper wire)



50mm or more

opaque, translucent or

specular object (Note 3)

Green LED (lights up

when the power is ON)

located on the emitter

Summary of content (2 pages)

PAGE 1
Thank you very much for using SUNX products. Please read this Instruction Manual carefully and thoroughly for the correct and optimum use of this product. Kindly keep this manual in a convenient place for quick reference. INSTRUCTION MANUAL c MOUNTING 䢇 The tightening torque should be 0.5N·m or less. 䢇 Never use this product as a sensing device for personnel protection. 䢇 In case of using sensing devices for personnel protection, use products which meet standards, such WARNING as OSHA, ANSI or IEC etc.
PAGE 2
Thru-beam Light received condition Emitter Receiver , SLIT MASK (OPTIONAL) Dark condition Emitter Receiver (Exclusively for thru-beam type sensor) 䢇 With the slit mask (OS-CX- M), the sensor can detect a small object. However, the sensing range is reduced when the slit mask is mounted. Sensing object Diffuse reflective Narrow-view reflective Retroreflective 䢇 Beam alignment Thru-beam type sensor q Set the operation mode switch to the Light-ON mode position (L side).