Digital Camera Operating Instructions

ManualsBrandsPanasonic ManualsDigital CameraDMC-LC1GN

Digital Camera

Operating Instructions

Model No.DMC-LC1GN

Before use, please read these

instructions completely.

VQT0H07

LC1-GN.book 1 ページ２００４年１月２９日　木曜日　午前９時１５分

Summary of content (128 pages)

PAGE 1
LC1-GN.book 1 ページ２００４年１月２９日木曜日午前９時１５分 Digital Camera Operating Instructions Model No. DMC-LC1GN Before use, please read these instructions completely.
PAGE 2
LC1-GN.book 2 ページ２００４年１月２９日木曜日午前９時１５分 Safety Safety Dear Customer, We would like to take this opportunity to thank you for purchasing this Panasonic Digital Camera. Please read these Operating Instructions carefully and keep them handy for future reference. • Please note that the actual controls and components, menu items, etc. of your Digital Camera may look somewhat different from those shown in the illustrations in these Operating Instructions. • SD Logo is a trademark.
PAGE 3
LC1-GN.book 3 ページ２００４年１月２９日木曜日 Contents 午前９時１５分 9 Pictures Multi Playback .................. 53 Using the Playback Zoom ................. 54 Deleting Pictures ............................... 55 Safety Recording pictures (advanced) Information for Your Safety ................. 2 Preparation Recording Motion Images ................. 58 FUNCTION Menu.............................. 60 Setting the White Balance ................. 61 Setting the White Balance manually (White set) ........................
PAGE 4
LC1-GN.book 4 ページ２００４年１月２９日木曜日 Using a Printer (USB Direct-Print)... 103 Others Using the External Flash ................. 105 Using the Wide Conversion Lens/ Close-up Lens ............................. 108 After Use ......................................... 110 Screen Display ................................ 111 The Menu Items .............................. 113 Cautions for Use ............................. 115 Approximate number of recordable pictures and the size....................
PAGE 5
LC1-GN.book 5 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Preparation Standard Accessories Before using your camera, check the contents.
PAGE 6
LC1-GN.book 6 ページ２００４年１月２９日木曜日午前９時１５分 Preparation ∫ Remote Shutter DMW-RS1 ∫ Lens Cap VYK1F94 ∫ CD-ROM ∫ Strap VFC4037 • Please order VYC0913 as repair parts. ∫ Lens Hood VYQ2884 ∫ Hood Cap VYK1C96 ∫ MC Protector (Filter diameter: 69 mm) DMW-LMC69 • Please order VYC0917 as repair parts.
PAGE 7
LC1-GN.
PAGE 8
LC1-GN.
PAGE 9
LC1-GN.book 9 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Charging the Battery Charge the battery before using. 1 Connect the AC cable. 3 • The AC cable does not fit entirely into the AC input terminal. A gap will remain as shown below. ¬Suggestions/Tips ¬ • After use, be sure to disconnect the AC cable. • The battery becomes warm after use/ charge or during charge. The camera also becomes warm during use. However, it is not a malfunction. • The battery and AC adaptor are designed only for this camera.
PAGE 10
LC1-GN.book 10 ページ２００４年１月２９日木曜日午前９時１５分 Preparation About the Battery ª Battery indication The remaining battery power appears on the screen. (This does not appear when using AC adaptor) > > > (The indication turns red and blinks): Recharge or replace the battery. ª Charging time and available recording time Measured under the following conditions: • Temperature: 25°C/Humidity: 60% • Recording once every 30 seconds, flash every other record.
PAGE 11
LC1-GN.book 11 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Inserting the Battery Preparation • Check if the camera is turned off. • Close the flash. 1 3 Slide the lever to open the battery door. SE CLO Close the battery door and then slide the battery door open/close lever. OPE N SE CLO 2 Insert the battery fully until the lock 1 pops on the battery. • Hold both sides of the battery when inserting.
PAGE 12
LC1-GN.book 12 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Removing the Battery Preparation • Check if the camera is turned off. • Close the flash. 1 3 Slide the lever to open the battery door. SE CLO Close the battery door and then slide the battery door open/close lever. OPE N SE CLO 2 Push the lock 1 to remove the battery. OPE N ¬Suggestions/Tips ¬ • If you will not use the camera for a long time, remove the battery.
PAGE 13
LC1-GN.book 13 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Using the AC Adaptor You can use the camera without worrying about battery discharge by connecting to an AC adaptor. Preparation • Check if the camera is turned off. • Close the flash. 1 Connect the AC cable. 2 Slide the terminal door to open. 3 Connect the DC cable. ¬Suggestions/Tips ¬ • Use the supplied DC cable. If you use other DC cables, it may cause a malfunction. • The camera becomes warm during use. This is not a malfunction.
PAGE 14
LC1-GN.book 14 ページ２００４年１月２９日木曜日午前９時１５分 Preparation About the Card ª Access to the card ª SD Memory Card (supplied) and MultiMediaCard (optional) When the card is accessed, the card access indication 1 lights. P The SD Memory Card and MultiMediaCard are small, lightweight, removable external memory cards. The reading/writing speed of an SD Memory Card is fast. The SD Memory Card is equipped with a Write-Protect switch A that can inhibit writing and formatting a card.
PAGE 15
LC1-GN.book 15 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Inserting the Card Preparation • Check if the camera is turned off. • Close the flash. 1 Slide the card door to open. 2 Insert the card with the label facing the rear of the camera until it clicks. 3 • Insert the card, pressing gently until it locks in place. If the card will not insert freely, it may be reversed. Do not force the card. • Do not touch the connection terminals on the back side of the card. 15 Close and slide the card door.
PAGE 16
LC1-GN.book 16 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Removing the Card Preparation • Check if the camera is turned off. • Close the flash. 1 Slide the card door to open. 3 2 Push the card until it clicks then pull the card out upright. ¬Suggestions/Tips ¬ Close and slide the card door. • The card and the data may be damaged if it is removed while the camera is on. • If the card door cannot be completely closed, remove the card and insert it again.
PAGE 17
LC1-GN.book 17 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Attaching the MC Protector/Lens Cap/Lens Hood/Hood Cap Preparation • Check if the camera is turned off. • Close the flash. ª Attaching the MC Protector ª Attaching the lens cap 1 1 Attach the MC protector. • The MC protector is a transparent filter which affects neither the colours nor the amount of light, so it can always be used to protect the camera’s lens. • You can also attach the lens hood. Attach the lens cap.
PAGE 18
LC1-GN.book 18 ページ２００４年１月２９日木曜日午前９時１５分 Preparation • When attaching the lens hood, use the dedicated hood cap. You cannot use the lens cap. • When taking pictures with flash, photo flash is interrupted by the lens hood and the bottom of the screen becomes dark. (vignetting effect) • When taking pictures with flash, we recommend detaching the lens hood. • Consult the dealer or your nearest servicentre if you lose the supplied accessories. (You can purchase the accessories separately.
PAGE 19
LC1-GN.book 19 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Attaching the Strap 1 2 1 Pressing both sides of the cover. 2 Pull out the black strap holder completely. Detach the black strap holder from the metal fitting. • When the black strap holder is completely detached, attach it again as above. 3 Pass the metal fitting through the eyelet of the camera. 4 Rotate the black strap holder in the opposite direction until it clicks. 5 Slide the cover until it is attached firmly.
PAGE 20
LC1-GN.book 20 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Setting the Date/Time (Clock Set) ª Initial Use 1 The clock is not set when the camera is shipped. When you turn the camera on, the clock setting screen appears. Select [CLOCK SET] from the [SETUP] menu. (P22) SETUP 2/3 REC MF ASSIST CUSTOM SET. NO.RESET CLOCK SET PLEASE SET THE CLOCK CLOCK SET MENU SELECT SET MF1 EXIT MENU MENU • When pressing the [MENU] button, the screen shown in step 2 appears. Set the clock on it.
PAGE 21
LC1-GN.book 21 ページ２００４年１月２９日木曜日午前９時１５分 Preparation 3 ¬Suggestions/Tips ¬ Select [D/M/Y], [M/D/Y] or [Y/M/D]. • You can set the year from 2000 to 2099. The 24-hour system is used. • After the fully charged battery has been inserted for more than 24 hours, the clock setting is stored (in the camera) for max. 3 months after the battery was removed, in accordance with the elapsed time after the battery is inserted. (The time may be shorter if the battery is not charged sufficiently.
PAGE 22
LC1-GN.book 22 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Setup Menu 1 4 Turn the camera on. Select the desired item. REC SETUP MONITOR AUTO REVIEW ON OFF 1SEC. 3SEC. ZOOM OFF REVIEW BEEP POWER SAVE SELECT 5 2 MENU REC AUTO REVIEW SELECT 2560 SELECT EXIT MENU SET 2MIN. EXIT MENU • Close the menu by pressing the [MENU] button after finishing the setting. SETUP 1/3 SET 1/3 OFF 1SEC. 3SEC. ZOOM BEEP POWER SAVE Select the [SETUP] Menu.
PAGE 23
LC1-GN.book 23 ページ２００４年１月２９日木曜日午前９時１５分 Preparation You can control the following items on [SETUP] menu. Menu Functions MONITOR/ FINDER Adjust the brightness of the LCD monitor (when pictures appear on the LCD monitor) or Viewfinder (when pictures appear on the Viewfinder) in 7 steps. AUTO REVIEW°1 • [OFF]: • • • • • • The recorded picture does not automatically appear. [1SEC.]: The recorded picture automatically appears on the screen for about 1 second. [3SEC.
PAGE 24
LC1-GN.book 24 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Menu Functions BEEP You can set [BEEP] and [SHUTTER] in the recording mode, and [BEEP] in playback mode. • Setting on [BEEP] (Setting on [BEEP] in recording mode) •[ ]: The operational sound turns high. •[ ]: The operational sound turns low. •[ ]: The operational sound turns off. • Setting on the shutter sound • You can select the shutter sound from [ 1 ], [ 2 ] and [ 3 ].
PAGE 25
LC1-GN.book 25 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Menu Functions CLOCK SET Change the date and time. (P20) RESET°1 The camera is reset to the initial settings. However, the folder number and the clock settings are not changed. USB MODE Set before connecting to a PC or a printer. (P95) LANGUAGE Set to the language on the menu screen from the following 7 languages. Set to the desired language with 2/1 and determine it with 4/[REVIEW].
PAGE 26
LC1-GN.book 26 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Using the LCD Monitor/Viewfinder The LCD monitor of the camera is easy to be viewed out of doors because the LCD monitor reflects sunlight to use it as a backlight. ª Switching the screen to be turned on In recording mode P Press the [EVF/LCD] button to switch to the screen you would like to turn on.
PAGE 27
LC1-GN.book 27 ページ２００４年１月２９日木曜日午前９時１５分 Preparation ª Diopter adjustment ª Monitor priority This feature is useful for users who wear corrective lenses and prefer to use the Viewfinder. When setting [PLAY ON LCD] (P25) to [ON] on the [SETUP] menu, the LCD monitor is turned on in the following cases. You can save the time to switch the display to the LCD monitor even when using the Viewfinder in recording.
PAGE 28
LC1-GN.book 28 ページ２００４年１月２９日木曜日午前９時１５分 Preparation About the Exposure • A histogram is a graph that displays brightness along the horizontal axis (black to white) and the number of pixels at each brightness level on the vertical axis. • It allows the camera user to easily check the way a picture is being exposed.
PAGE 29
LC1-GN.book 29 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Operational Mode Dial and Metering Mode Dial ª Operational mode dial ª Metering mode dial You can switch to the recording mode (single/burst) and the playback mode. You can switch to the following metering methods. Metering mode : Single mode (P34) Details of setting : Burst mode (P50) [ ] Multiple The camera automatically evaluates the whole screen and optimizes the exposure. Usually, we recommend using this metering mode.
PAGE 30
LC1-GN.book 30 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Setting the Exposure You can set the exposure by setting the aperture ring and the shutter speed dial. ª Aperture-priority AE mode [ 90 75 35 50 3.2 4 6 10 1.2 2 3 25 8 2 2.8 4 5.6 8 30 5 10 00 500 0 25 12 00 60 4 8s 20 AF AF-Macro 11 A 15 8 2– A When you want the background to be in sharp focus, set the aperture value to a higher number. The higher the aperture value, the smaller the aperture opening will be.
PAGE 31
LC1-GN.book 31 ページ２００４年１月２９日木曜日午前９時１５分 Preparation ª Manual exposure mode [ • When adjusting the shutter speed dial to [2–8s], rotate the command dial or set the shutter speed with 2/1. Decide the exposure by setting the aperture value and the shutter speed manually. S ISO100 2560 20 00 1000 0 50 25 0 125 60 8 Adjust the aperture ring between 2 and 11, and the shutter speed dial between 2000 and 2–8s. 30 A 15 4 2–8s ] 19 M ISO100 2560 19 1/2 REVIEW F2.
PAGE 32
LC1-GN.book 32 ページ２００４年１月２９日木曜日午前９時１５分 Preparation ª Manual Exposure Assistance ¬Suggestions/Tips ¬ When you press the shutter button halfway, the indication for the condition of exposure (manual exposure assistance) appears for about 10 seconds. ª Manual exposure mode [ ] • Refer to P33 for the available range of the aperture value and the shutter speed. • The focus range is 60 cm–¶ (AF), 30 cm–¶ (AF-Macro/MF). • You cannot set the following items in manual exposure mode.
PAGE 33
LC1-GN.book 33 ページ２００４年１月２９日木曜日午前９時１５分 Preparation Shutter Speed and Aperture Value ª Shutter-priority AE mode Available Shutter Speed (Sec.) (Per 1/3 EV) Aperture value F2.0 °1– F11 8 4 2 1 1/2 1/4 1/8 1/15 1/250 1/30 1/60 1/125 1/500 1/1000 1/2000 F2.0 – F11 °1The smaller aperture value is limited depending on the shutter speed or ISO sensitivity. ª Aperture-priority AE mode Available Aperture value (Per 1/3 EV) Shutter Speed (Sec.) F11 F10 F9.0 F8.0 F7.1 F6.3 F5.6 F5.
PAGE 34
LC1-GN.book 34 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) Recording pictures (basic) Taking Pictures with Auto Focus Preparation • Insert the charged battery (P11) or connect the AC adaptor (P13). • Insert the card. (P15) • Remove the lens cap. • When adjusting the focus ring A to [AF], rotate the focus ring with pressing the focus ring button B. 1 Turn the camera on. 2 Set the operational mode dial to single mode [ ]. (P29) 3 Set to the exposure.
PAGE 35
LC1-GN.book 35 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) ª Taking pictures close to the subject (AF-Macro) • The focus indication D lights and then the aperture value E and the shutter speed F appear. • When the focus indication D is blinking, the subject is not focused. Press the shutter button halfway and focus on the subject again. When adjusting the focus ring to [AF-Macro], you can take pictures approaching the lens at a distance up to 30 cm from the subject.
PAGE 36
LC1-GN.book 36 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) ª Focusing ª Jitter (Camera shake) • The focus range is 60 cm–¶ (AF). It is 30 cm–¶ (AF-Macro/MF). • If you press the shutter button fully without prefocusing, pictures may be blurry or unfocused. • When the focus indication is blinking, the subject is not focused. Press the shutter button halfway and focus on the subject again. • When the subject is focused, the camera beeps 2 times. If not, it beeps 4 times.
PAGE 37
LC1-GN.book 37 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) ¬Suggestions/Tips ¬ When recording with LCD Monitor • When pressing the shutter button halfway, the screen may become dark or bright for a moment; this is not a malfunction. This is caused by adjusting the aperture value. • When you slow the shutter speed, the shutter may be kept closed after recording due to the signal conditioning. This is not a malfunction. • We recommend setting the clock again before taking pictures.
PAGE 38
LC1-GN.book 38 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) ª AF/AE Lock (AF: Auto Focus/ AE: Auto Exposure) P ª Programme shift In Programme AE mode, you can change the preset aperture value and the shutter speed under the same exposure. This is called Programme shift. By this function, you can make the background more blurred (by decreasing the aperture value) or record the subject in motion dynamically (by setting to slow shutter speed) in Programme AE mode.
PAGE 39
LC1-GN.book 39 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) 2 (A) 3 4 5 6 7 8 9 10 11 12 13 14 2 15 2.8 16 4 17 5.6 18 8 19 11 1 1/2 1/4 1/8 1/15 1/30 1/60 1/125 1/250 1/500 1/1000 1/2000 (B) (A): Aperture value (B): Shutter speed ¬Suggestions/Tips ¬ • If the exposure is not adequate when pressing the shutter button halfway, the shutter speed turns red.
PAGE 40
LC1-GN.book 40 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) Taking Pictures with Manual Focus Use this function when you want to fix the focus or when the distance between the lens and the subject is determined and you do not want to activate the auto focus. Preparation • Set the operational mode dial except for [ 1 ]. (P29) 2 Select [MF ASSIST] from the [SETUP] menu (in the recording mode) (P22) and then set it to [MF1] or [MF2]. Rotate the focus ring to focus on the subject.
PAGE 41
LC1-GN.book 41 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) ª MF ASSIST ¬Suggestions/Tips ¬ When you rotate the focus ring with setting [MF ASSIST] to [MF1] or [MF2], the MF assistance is activated and the screen is enlarged. It allows you to focus on the subject more easily. • [MF1]: The centre of the screen is enlarged. You can adjust the focus while determining composition of the whole of the screen. • [MF2]: The whole of the screen is enlarged.
PAGE 42
LC1-GN.book 42 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) Checking the Recorded Picture (Review) Preparation • In Motion image mode, review function is not activated. 1 2 Press 4/[REVIEW]. Enlarge and shift the picture. REVIEW4X REVIEW1X EXIT 4X 1X DELETE 8X DELETE • The last recorded picture appears for about 10 seconds. • Press the shutter button halfway or 4/[REVIEW] to cancel the review. • You can check the previous or following picture with 2/1.
PAGE 43
LC1-GN.book 43 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) Using the Optical Zoom You can bring people or objects into close-up or record landscapes widely in the range of optical zoom up to 3.2k (35 mm-camera equivalent: 28– 90 mm) by rotating the zoom ring. Preparation • Set the operational mode dial except for [ ]. (P29) ª To make subjects appear closer (Tele) P 2560 19 90 75 P 2 2.8 4 5.6 8 90 75 35 50 25 8 28 28 [ 35mm EQIV.
PAGE 44
LC1-GN.book 44 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) Taking Pictures using the Built-in Flash Preparation • Set the operational mode dial except for [ ª To open the flash Press the [ before the actual recording of the picture. Use this when you take pictures of people in low lighting conditions. OPEN] button. : Forced ON The flash is activated every time a picture is recorded forcibly. Use this when your subject is back-lit or under fluorescent light.
PAGE 45
LC1-GN.book 45 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) ª Adjusting flash output Use this when taking pictures in places where use of the flash is not allowed. Adjust the flash output when the subject is small or reflection ratio is extremely high or low. • Refer to P71 for setting the 1st and 2nd curtain.
PAGE 46
LC1-GN.book 46 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) You can fix the flash slanting at an angle of about 65o as follows in bounce flash. (Bounce flash lock) • The flash icon turns red when activating the flash and pressing the shutter button halfway. • When the flash is being charged, the flash icon blinks red, and you cannot take a picture even when you press the shutter button fully. • When taking a picture with the flash, we recommend removing the lens hood.
PAGE 47
LC1-GN.book 47 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) Compensating the Exposure Use this function when you cannot achieve appropriate exposure due to the difference of brightness between the subject and the background. Preparation • Set the operational mode dial except for [ 1 ¬Suggestions/Tips ¬ Press [ ] until [ EXPOSURE] appears on the screen to compensate the exposure.
PAGE 48
LC1-GN.book 48 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) Taking Pictures using Auto Bracket This mode allows you to take pictures automatically according to the compensation range of the exposure by pressing the shutter button only once. You can select the picture with the desired exposure among different exposures.
PAGE 49
LC1-GN.book 49 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) Taking Pictures with the Self-timer Preparation • Set the operational mode dial except for [ 1 2 Switch the self-timer setting. P ]. (P29) 2560 19 Focus on the subject to take the picture. P 2560 19 CANCEL MENU REVIEW : Self-timer set to 10 seconds ; : Self-timer set to 2 seconds ; No display (cancelled) • If you press the [MENU] button when the self-timer is set, the self-timer setting is cancelled.
PAGE 50
LC1-GN.book 50 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (basic) Taking Pictures using Burst Mode Preparation • Set the operational mode dial to burst mode [ 1 Select [BURST RATE], set [ H] or [ L ] and then take pictures. REC 2/4 SETUP SPOT AF SENSITIVITY BURST RATE max. max. max. 12 frames 23 frames 44 frames 640 max. max. max. 44 frames 80 frames 137 frames SET EXIT MENU REVIEW REVIEW • Keep pressing the shutter button fully to activate the burst mode.
PAGE 51
LC1-GN.book 51 ページ２００４年１月２９日木曜日午前９時１５分 Playback (basic) Playback (basic) Playing Back Pictures Preparation • Set the operational mode dial to playback mode [ 1 ]. (P29) • When releasing 2/1, the number of file forwarded begins from 1. • While forwarding or rewinding a large number of pictures by holding down 2/1, once release 2/1 before reaching the picture to be played back, then press 2/1 to forward/rewind pictures until the desired picture appears.
PAGE 52
LC1-GN.book 52 ページ２００４年１月２９日木曜日 Playback (basic) ¬Suggestions/Tips ¬ • This camera is based on the DCF standards (Design rule for Camera File system) which were established by the Japan Electronics and Information Technology Industries Association (JEITA). • When changing the folder name or file name on PC, the pictures may not be played back. • The file format that can be played back with this camera is JPEG. (There are also pictures that cannot be played back in JPEG format.
PAGE 53
LC1-GN.book 53 ページ２００４年１月２９日木曜日午前９時１５分 Playback (basic) 9 Pictures Multi Playback Preparation • Set the operational mode dial to playback mode [ 1 2 Switch to multi screen. ]. (P29) Select the pictures. 2560 100 _ 0001 1/19 10:00 1.JAN.2004 1 2 3 4 5 6 7 8 9 SELECT REVIEW REVIEW 1 2 3 4 5 6 7 8 9 SELECT CANCEL 10 11 SELECT CANCEL 12 CANCEL ª To return to the normal indication Rotate the command dial clockwise.
PAGE 54
LC1-GN.book 54 ページ２００４年１月２９日木曜日午前９時１５分 Playback (basic) Using the Playback Zoom Preparation • Set the operational mode dial to playback mode [ 1 ª To delete a picture during the playback zoom Enlarge the picture. Press the [ ] button. When the confirmation screen appears, press 2 to select [YES], and press 4/[REVIEW]. (P55) 2X ¬Suggestions/Tips ¬ 4X CANCEL • The more the picture is enlarged, the more its quality deteriorates.
PAGE 55
LC1-GN.book 55 ページ２００４年１月２９日木曜日午前９時１５分 Playback (basic) Deleting Pictures Preparation • Set the operational mode dial to playback mode [ ª To delete single picture 1 Select the picture to be deleted. 2560 100 _ 0001 1/19 10:00 1.JAN.2004 REVIEW • Press 2 to play back the previous picture. • Press 1 to play back the next picture. 2 Delete the picture. DELETE SINGLE DELETE THIS PICTURE? YES SELECT SET NO MULTI/ALL REVIEW REVIEW 55 ].
PAGE 56
LC1-GN.book 56 ページ２００４年１月２９日木曜日午前９時１５分 Playback (basic) ª To delete multi pictures 1 3 Select [MULTI DELETE]. Delete the pictures. MULTI DELETE MULTI/ALL DELETE MULTI DELETE ALL DELETE DELETE THE PICTURES YOU MARKED? YES SELECT SET CANCEL SELECT SET REVIEW REVIEW NO REVIEW 2 times 2 • It is possible to delete up to 50 pictures all at once. Select the pictures to be deleted.
PAGE 57
LC1-GN.book 57 ページ２００４年１月２９日木曜日午前９時１５分 Playback (basic) ª To delete all pictures ¬Suggestions/Tips ¬ 1 • Once deleted, pictures cannot be recovered. Please double-check before deleting pictures. • Pictures that are protected (P84) or not of DCF standards (P52) are not deleted. • Do not turn off the camera while deleting. • When the remaining battery power (P10) is low, use the AC adaptor. Select [ALL DELETE].
PAGE 58
LC1-GN.book 58 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) Recording pictures (advanced) Recording Motion Images You can record motion images with audio. Preparation • Set the operational mode dial except for [ 1 ]. (P29) • [30 fps]: The motion of recorded image is smooth, but the file size is large. • [10 fps]: The file size is smaller so you can record motion images for a longer time. • fps (frame per second): This means the number of frames used in 1 second.
PAGE 59
LC1-GN.book 59 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) 4 ¬Suggestions/Tips ¬ Press the shutter button fully to start the recording. • The picture size is fixed to 320k240 pixels. • The motion images cannot be recorded without audio. • If you rotate the zoom ring, the focus ring or the aperture ring when recording audio (when recording motion images, pictures with audio, etc.), the rustling of the lens barrel is also recorded.
PAGE 60
LC1-GN.book 60 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) FUNCTION Menu You can select 4 menus which you frequently use from the menus in the recording mode (P113, P114). This allows you to select the menu and save the time to operate it at the minimum. • The white balance, the white balance fine adjustment, the ISO sensitivity and the spot AF are included in FUNCTION menu in initial setting. 1 4 Select [SETUP].
PAGE 61
LC1-GN.book 61 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) Setting the White Balance In certain situations, the colour white may appear slightly reddish or bluish. This can occur when shooting under early or late day sunlight, on a cloudy day, or under halogen lighting. By using the manual White Balance feature you can achieve a more accurate reproduction of the colour white.
PAGE 62
LC1-GN.book 62 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) Use of auto white balance adjustment in inappropriate lighting conditions may result in reddish or bluish pictures. Where the subject is surrounded by many light sources, auto white balance adjustment may not operate properly. In this case, set the white balance to the mode except [AUTO] manually.
PAGE 63
LC1-GN.book 63 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) Setting the White Balance manually (White set) Preparation • Set the operational mode dial except for [ 1 Select [W.BALANCE] and set to [ ]. REC 1/4 ¬Suggestions/Tips ¬ • When setting the white balance to the mode except for [AUTO] or [ B/W ] (monochrome), you can finely adjust the white balance. (P64) • The setting of the white balance is applied to the other recording modes.
PAGE 64
LC1-GN.book 64 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) Finely Adjusting the White Balance If you cannot acquire the desirable hue with white balance because of too many different light sources, etc., adjust the fine white balance as follows. Preparation • Set the operational mode dial except for [ • Set the white balance to [ 1 ]/[ ]/[ ]/[ 2 Select [WB ADJUST.]. REC 1/4 W.BALANCE WB ADJUST. PICT.SIZE QUALITY SELECT SET ]. (P29) WB ]/[ ]. (P61) Adjust the white balance.
PAGE 65
LC1-GN.book 65 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) Changing the Picture Size Preparation • Set the operational mode dial except for [ 1 ¬Suggestions/Tips ¬ Select [PICT.SIZE] and set the picture size. REC 1/4 W.BALANCE WB ADJUST. PICT.SIZE • In Motion image mode, the picture size is fixed to 320k240 pixels. • If you playback pictures recorded using [HDTV] mode on a High-Definition TV, (HDTV has 16:9 aspect) the picture quality will be higher.
PAGE 66
LC1-GN.book 66 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) Changing the Quality “Quality” refers to the amount each image is compressed. Lower compression results in superior picture quality. Higher compression allows you to store more images on your SD Memory card. Preparation • Set the operational mode dial except for [ 1 ¬Suggestions/Tips ¬ Select [QUALITY] and set the quality.
PAGE 67
LC1-GN.book 67 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) Taking Pictures using the Spot AF The focus is adjusted within the limited range. Preparation • Set the operational mode dial except for [ 1 3 Select [SPOT AF] and set it to [ON]. REC 2/4 ]. (P29) Move the camera to compose the picture fixing the focus on the subject and take the picture. SETUP P SPOT AF OFF 2560 19 ON SENSITIVITY BURST MODE AUDIO REC. SELECT SET 100 OFF EXIT MENU F2.
PAGE 68
LC1-GN.book 68 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) Setting ISO Sensitivity The ISO setting sets the cameras sensitivity to light. The ISO setting can be increased when you need to take pictures in places where a flash may not be allowed. The overall picture quality will decrease slightly as the ISO setting is increased. ISO sensitivity 100 400 Use in bright places (E.g.
PAGE 69
LC1-GN.book 69 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) Taking Pictures with Audio Preparation • Set the operational mode dial except for [ 1 2/4 OFF AUTO OFF SELECT • It is not necessary to keep pressing the shutter button. • Audio is recorded from the built-in microphone 1 of the camera. SETUP SPOT AF SENSITIVITY BURST RATE AUDIO REC. ]. (P29) ¬Suggestions/Tips ¬ Select [AUDIO REC.] and set it to [ON].
PAGE 70
LC1-GN.book 70 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) Using the Digital Zoom Preparation • Set the operational mode dial except for [ ]. (P29) ¬Suggestions/Tips ¬ • It is possible to further magnify a subject already magnified 3.2 times with the optical zoom by 3 more times, with the digital zoom, thereby reaching a maximum of 9.6 times (35 mm-camera equivalent: 90– 270 mm). • When using the digital zoom the picture quality becomes deteriorated.
PAGE 71
LC1-GN.book 71 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) Setting to the 2nd Curtain Synchro The 2nd curtain synchro is the method that the photo flash activates just before the shutter is released when you take pictures of the subject with motion using slow shutter and the photo flash. The light source appears at the back of the subject and the picture becomes dynamic. Preparation • Set the operational mode dial except for [ ª 1st curtain synchro P A ]. (P29) 1 Select [FLASH SYNC.
PAGE 72
LC1-GN.book 72 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) Adjusting the Quality of the Picture (Picture Adjustment) Preparation • Set the operational mode dial except for [ 1 • [CONTRAST]: HIGH: Increases the difference between the brightness and the darkness in the picture. LOW: Decreases the difference between the brightness and the darkness in the picture. • [SHARPNESS]: HIGH: The picture is sharply defined. LOW: The picture is softly focused.
PAGE 73
LC1-GN.book 73 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) Creating Flip Animation This camera allows you to create motion picture files up to 20 seconds by connecting images recorded in flip animation mode. Preparation • Set the operational mode dial except for [ ]. (P29) ª Capturing images Example: When capturing images of the subject in sequence moving it little by little and aligning the images, the subject looks as if it were moving. 1 Select [FLIP ANIM.].
PAGE 74
LC1-GN.book 74 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) 3 ª Creating motion images Capture images for flip animation. 5 P Select [CREATE MOTION IMAGE]. 320 8 REMAIN 92 FLIP ANIM. IMAGE CAPTURE CREATE MOTION IMAGE DELETE STILL IMAGES EXIT MENU SELECT SET EXIT MENU MENU REVIEW REVIEW • You can take up to 100 pictures. 4 Check the image. REVIEW 6 320 Select [FRAME RATE] and set the number of frames.
PAGE 75
LC1-GN.book 75 ページ２００４年１月２９日木曜日午前９時１５分 Recording pictures (advanced) 7 ª Playing back a created flip animation Select [CREATE MOTION IMAGE] and create a flip animation. Follow the same procedure as you play back motion images. (P77) CREATE MOTION IMAGE 5 fps FRAME RATE CREATE MOTION IMAGE SELECT SET ª Deleting all of still pictures used for flip animation When selecting [DELETE STILL IMAGES] in flip animation screen, a confirmation screen appears. Select [YES] and then press 4/[REVIEW].
PAGE 76
LC1-GN.book 76 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Playback (advanced) Playing Back Pictures with Audio Preparation • Set the operational mode dial to playback mode [ 1 ¬Suggestions/Tips ¬ Select the picture with audio icon [ ]. • The picture with audio cannot be resized (P89) or trimmed (P91). 2560 100 _ 0001 1/19 PLAY AUDIO 10:00 1.JAN.2004 REVIEW 2 ]. (P29) Play back the audio. 2560 100 _ 0001 1/19 10:00 1.JAN.2004 REVIEW • You can hear audio from the speaker.
PAGE 77
LC1-GN.book 77 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Playing Back Motion Images Preparation • Set the operational mode dial to playback mode [ 1 ª Fast forwarding/Fast rewinding Select the picture with the motion image icon [ ]. PLAY MOTION IMAGE ]. (P29) During motion image playback, continue pressing 2/1. 1: Fast forward 2: Fast rewind 100 _ 0001 1/19 • When releasing the button, it turns to normal motion image playback. ª To pause 10:00 1.JAN.
PAGE 78
LC1-GN.book 78 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Rotating the Picture You can rotate the recorded pictures in increments of 90°. This is a convenient function to play back pictures on TV. Preparation • Set the operational mode dial to playback mode [ 1 • Close the menu by pressing the [MENU] button after finishing the setting. Select [ROTATE]. PLAY 1/2 SETUP ROTATE PROTECT DPOF PRINT SLIDE SHOW AUDIO DUB.
PAGE 79
LC1-GN.book 79 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Setting the Picture to be Printed and the Number of Prints (DPOF Print Setting) DPOF (Digital Print Order Format) is a system that allows the user to select which pictures are to be printed on compatible photo printers. DPOF also allows the user to set how many copies of each picture will be printed. Many commercial photo printing services now use DPOF. Preparation • Set the operational mode dial to playback mode [ ].
PAGE 80
LC1-GN.book 80 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) ª Multi setting/cancel 1 3 Select [DPOF PRINT]. PLAY 1/2 ROTATE PROTECT DPOF PRINT SLIDE SHOW AUDIO DUB. SELECT SET Select the pictures and set the number of prints. SETUP DPOF SET MULTI 1 8 7 10 COUNT SELECT EXIT MENU 9 11 001 12 DATE DISPLAY EXIT MENU MENU REVIEW REVIEW REVIEW 2 Select [MULTI]. PLAY 1/2 ROTATE PROTECT DPOF PRINT SLIDE SHOW AUDIO DUB.
PAGE 81
LC1-GN.book 81 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) ª To cancel all settings 1 3 Select [DPOF PRINT]. PLAY 1/2 ROTATE PROTECT DPOF PRINT SLIDE SHOW AUDIO DUB. SELECT SET SETUP Select [YES] to cancel all settings. CANCEL ALL DPOF CANCEL ALL DPOF PRINT SETTINGS? YES SELECT EXIT MENU NO SET MENU REVIEW REVIEW 2 REVIEW • Close the menu by pressing the [MENU] button after cancelling the setting. Select [CANCEL]. PLAY 1/2 ROTATE PROTECT DPOF PRINT SLIDE SHOW AUDIO DUB.
PAGE 82
LC1-GN.book 82 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) ª Index setting/cancel 1 3 Select [DPOF PRINT]. PLAY 1/2 ROTATE PROTECT DPOF PRINT SLIDE SHOW AUDIO DUB. SELECT SET Select [YES] to index setting. SETUP DPOF INDEX SET INDEX PRINT? YES SELECT EXIT MENU NO SET MENU 2 REVIEW REVIEW REVIEW • Close the menu by pressing the [MENU] button after finishing the setting. Select [INDEX]. PLAY 1/2 ROTATE PROTECT DPOF PRINT SLIDE SHOW AUDIO DUB.
PAGE 83
LC1-GN.book 83 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) ª When the index is already set ¬Suggestions/Tips ¬ • DPOF print setting is a convenient function when you print pictures with printers supporting DPOF printing. • DPOF is the abbreviation for Digital Print Order Format. This feature allows you to designate which pictures will be printed. • The setting of DPOF print will not be applied to the DPOF setting of Slide Show.
PAGE 84
LC1-GN.book 84 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Preventing Accidental Erasure of the Picture Preparation • Set the operational mode dial to playback mode [ ]. (P29) ª Single setting/cancel 1 3 Select [PROTECT]. PLAY 1/2 SETUP PROTECT THIS ROTATE PROTECT DPOF PRINT SLIDE SHOW AUDIO DUB. SELECT Select the picture and set/cancel the protection. SET EXIT MENU SELECT SET/CANCEL 100 _ 0001 1/19 EXIT MENU MENU REVIEW REVIEW REVIEW 2 Select [SINGLE].
PAGE 85
LC1-GN.book 85 ページ２００４年１月２９日木曜日 Playback (advanced) ª Multi setting/To cancel all settings Perform the same operation as in [Setting the Picture to be Printed and the Number of Prints (DPOF Print Setting)]. (P79– P81) ¬Suggestions/Tips ¬ • While this feature protects the pictures from accidental erasure, formatting the card will permanently delete all data. (P93) • If you want to delete protected pictures, cancel the protect setting first. • The protect setting may not be effective in other equipment.
PAGE 86
LC1-GN.book 86 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Playing Back with Slide Show Preparation • Set the operational mode dial to playback mode [ 1 3 Select [SLIDE SHOW]. PLAY 1/2 SET Select the following items. SETUP ROTATE PROTECT DPOF PRINT SLIDE SHOW AUDIO DUB. SELECT ]. (P29) START DURATION 1SEC. 2SEC. 3SEC. 5SEC. AUDIO EXIT MENU SELECT OFF SET EXIT MENU MENU 2 REVIEW REVIEW REVIEW • [DURATION]: It can be set among 1, 2, 3 and 5 seconds.
PAGE 87
LC1-GN.book 87 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) 4 START DURATION AUDIO SELECT SET REVIEW 5 ¬Suggestions/Tips ¬ Select [START]. • When setting the DPOF Slide Show, DPOF icon 1 appears on the picture in green. • When setting the DPOF Slide Show to the picture with DPOF printing, both of DPOF icon 1 and the number of prints appear on the picture in green. • When only the DPOF printing is set on the picture, the DPOF icon 1 and the number of prints appear in white. 1SEC.
PAGE 88
LC1-GN.book 88 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Adding Audio to Recorded Pictures (Audio Dubbing) Preparation • Set the operational mode dial to playback mode [ 1 • The audio dubbing cannot be used with motion images, pictures with setting the quality to [ RAW ] or protected pictures. Select [AUDIO DUB.]. PLAY 1/2 SETUP ROTATE PROTECT DPOF PRINT SLIDE SHOW AUDIO DUB. SELECT ]. (P29) 3 Stop audio recording. AUDIO DUB.
PAGE 89
LC1-GN.book 89 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Resizing the Pictures This function is useful if you want to reduce the file size of the picture, in those cases when it needs to be attached to an E-mail or uploaded it to a web site. Preparation • Set the operational mode dial to playback mode [ 1 3 Select [RESIZE]. PLAY 2/2 Select the size and set it. SETUP RESIZE RESIZE TRIMMING FORMAT SELECT ].
PAGE 90
LC1-GN.book 90 ページ２００４年１月２９日木曜日 Playback (advanced) 4 Select [YES] or [NO] and set it. RESIZE DELETE ORIGINAL PICTURE? YES SELECT SET NO CANCEL MENU REVIEW REVIEW • When you select [YES], the picture is overwritten. • When the original picture is protected, you cannot overwrite the resized picture. • When resized pictures are overwritten, they cannot be restored. • Close the menu by pressing the [MENU] button 2 times after finishing the resizing.
PAGE 91
LC1-GN.book 91 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Trimming the Pictures Preparation • Set the operational mode dial to playback mode [ 2 ]. (P29) Select the picture to trim. TRIMMING SELECT SET REVIEW 3 1 2560 100 _ 0001 1/19 EXIT MENU REVIEW Enlarge/decrease or shift the picture. Select [TRIMMING].
PAGE 92
LC1-GN.book 92 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) 4 ¬Suggestions/Tips ¬ Select [YES] or [NO] and set it. • The following pictures cannot be trimmed. – Pictures smaller than 640k480 pixels – Pictures recorded with setting the picture size to [HDTV] – Pictures with setting the quality to [ RAW ] – Motion images – Flip animation – Pictures with audio – Rotated pictures (You can trim them if you rotate them back.) • It may not be possible to trim pictures recorded with other equipment.
PAGE 93
LC1-GN.book 93 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Formatting the Card Preparation • Set the operational mode dial to playback mode [ 1 ¬Suggestions/Tips ¬ Select [FORMAT]. PLAY 2/2 • Usually, it is not necessary to format the card (initializing). Format the card when the message [MEMORY CARD ERROR] appears. • If the card has been formatted by a PC or other equipment, format the card on the camera again. • After formatting, recorded pictures and any other data cannot be recovered.
PAGE 94
LC1-GN.book 94 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Playing Back Pictures with a TV Screen ª Playing back pictures with AV cable (supplied) • Turn the camera and the TV off. ª Viewing pictures in other countries When setting [VIDEO OUT] on the menu (P25), you can view pictures on a TV in other countries (regions) which use the NTSC or PAL system. 2 ª Playback pictures on TV with SD Memory Card slot USB An SD Memory Card can be played back on TVs with an SD Memory Card slot.
PAGE 95
LC1-GN.book 95 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Before Connecting with USB Connection Cable Select the USB communication system according to the OS of your PC or your printer before connecting them to the camera with the USB connection cable (supplied). Set the items on [USB MODE] in the [SETUP] menu. (P25) 1 2 Select [USB MODE]. (In the recording mode) SETUP 3/3 REC RESET USB MODE LANGUAGE SELECT Select [Mass Storage] or [PTP].
PAGE 96
LC1-GN.book 96 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) ª When using Windows 2000 Professional, Windows Me, Windows 98/98 SE or Mac OS 9.x • When connecting the camera to a PC, do not set [USB MODE] to [PTP]. (When the camera is shipped, [Mass Storage] is selected.) • When using [Mass Storage] on Windows 98/98 SE, install the USB driver before connecting. (When using Windows Me/2000/XP, Mac OS 9.x and Mac OS X, you do not have to install the USB driver.
PAGE 97
LC1-GN.book 97 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Connecting to a PC (Mass Storage) When you connect to the camera to a PC supporting USB 2.0 (High Speed), you can transfer the data with higher speed in a shorter period of time. • If it is the first time for you to connect the camera to a PC, the required driver is installed automatically so that the camera can be recognized by the Windows Plug and Play, then it appears on the [My Computer] folder.
PAGE 98
LC1-GN.book 98 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Connecting to a PC (PTP) Do not follow the setting below on the OS except for Windows XP and Mac OS X. • If it is the first time for you to connect the camera to a PC, the required driver is installed automatically so that the camera can be recognized by the Windows Plug and Play, then the camera icon appears on the [My Computer] folder. [Macintosh] You can read pictures with image capture or iPhoto.
PAGE 99
LC1-GN.book 99 ページ２００４年１月２９日木曜日 Playback (advanced) ¬Suggestions/Tips ¬ • Refer to P96 carefully when connecting to the OS except for Windows XP and Mac OS X with setting [USB MODE] to [PTP]. • When connecting to a PC, we recommend using the AC adaptor as the power source. • If the remaining battery power becomes low during communication, the power indicator blinks and the alarm beeps. In this case, stop the communication. Then turn the camera off and charge the battery.
PAGE 100
LC1-GN.book 100 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Connecting to a Printer By connecting the camera directly to a printer supporting PictBridge or USB Direct-Print via the USB connection cable (supplied), you can select the pictures to be printed or start printing. ¬Suggestions/Tips ¬ USB AV OUT/ REMOTE DC IN 1 Turn the camera on and then set the [USB MODE] to [Mass Storage] (USB Direct-Print) or [PTP] (PictBridge). (P95) 2 Turn on a printer.
PAGE 101
LC1-GN.book 101 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Using a Printer (PictBridge) Preparation • Connect the camera to a printer. (P100) • The paper size cannot be changed depending on the printer. For details, refer to the operating instructions of the printer. ª Single picture 1 Select [SINGLE PICTURE]. 3 Select [YES] and print.
PAGE 102
LC1-GN.book 102 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Preparation • Connect the camera to a printer. (P100) • Set the DPOF print with this camera in advance. (P79) • The paper size cannot be changed depending on the printer. For details, refer to the operating instructions of the printer. ª DPOF picture 1 2 Select [DPOF PICTURE]. Select [YES] and print.
PAGE 103
LC1-GN.book 103 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Using a Printer (USB Direct-Print) • Connect the camera to a printer. (P100) • Set the paper size and print quality. (Read the printer operating instructions.) ª Single picture 1 Select [SINGLE PICTURE]. 3 DIRECT PRINT DIRECT PRINT PLS CHECK THE PRINTER START PRINTING? COUNT 1 SINGLE DPOF PICTURE PICTURE SELECT YES SET COUNT SELECT SET REVIEW REVIEW REVIEW • The screen shown in step 2 appears when DPOF print is not set.
PAGE 104
LC1-GN.book 104 ページ２００４年１月２９日木曜日午前９時１５分 Playback (advanced) Preparation • Connect the camera to a printer. (P100) • Set the DPOF print with this camera in advance. (P79) • Set the paper size and print quality. (Read the printer operating instructions.) ª DPOF picture 1 Select [DPOF PICTURE]. 2 DIRECT PRINT DIRECT PRINT PLS CHECK THE PRINTER START PRINTING? SINGLE DPOF PICTURE PICTURE SELECT REVIEW Select [YES] and print.
PAGE 105
LC1-GN.book 105 ページ２００４年１月２９日木曜日午前９時１５分 Others Others Using the External Flash After installing the optional flash, DMW-FL28, the effective range will be increased when compared to the camera’s built in flash. Preparation • Set the operational mode dial except for [ 1 ]. (P29) External flash Slow sync. Attach the external flash to the hot shoe 1. External flash Forced OFF ª Available external flash settings • Tighten the lock screw 2 of the external flash firmly.
PAGE 106
LC1-GN.book 106 ページ２００４年１月２９日木曜日午前９時１５分 Others ª Using the specified external flashes ª Available external flash settings • When you use the following external flashes, the information about the ISO sensitivity, the aperture value or other on the camera is transferred to the flash and then you can use various functions of the flash such as the adjustment of the range of the light control according to the aperture value or the display of the range of the light control.
PAGE 107
LC1-GN.book 107 ページ２００４年１月２９日木曜日午前９時１５分 Others ¬Suggestions/Tips ¬ • You can set the aperture value, the shutter speed and the ISO sensitivity on the camera even when attaching the external flash. • Some commercial external flashes have synchro terminals with high-voltage or reversed polarity. Using such external flashes may cause a malfunction or the camera may not operate normally.
PAGE 108
LC1-GN.book 108 ページ２００４年１月２９日木曜日午前９時１５分 Others Using the Wide Conversion Lens/Close-up Lens The wide conversion lens (DMW-LW69, optional) allows you to take pictures with wider range of focus than usual (0.82 times, 35 mm-camera equivalent: 23 mm). The close-up lens (DMW-LC69, optional), if fitted onto the camera, will give a sharper close-up image. Its multi-coated lens provides a clearer picture. Preparation • Set the operational mode dial except for [ • Check if the camera is turned off. ].
PAGE 109
LC1-GN.book 109 ページ２００４年１月２９日木曜日 Others ¬Suggestions/Tips ¬ • When using the wide conversion lens, rotate the zoom ring to Wide (35 mm-camera equivalent: 28 mm). If you rotate the zoom ring to other position, the performance of the lens may not be brought out. • Check if the lens cap is removed before attaching the wide conversion lens. • If you use the built-in flash when using the wide conversion lens, take pictures with bounce flash.
PAGE 110
LC1-GN.book 110 ページ２００４年１月２９日木曜日午前９時１５分 Others After Use After using the camera, it is recommended that you complete the following steps: 1 Turn the camera off and close the flash. 3 Remove the hood cap and the lens hood (only when using it) and then attach the lens cap. ON OFF 2 Remove the card and the battery. (P12, P16) • When removing the lens hood, push the knob on the lens hood and then slide it to the front.
PAGE 111
LC1-GN.book 111 ページ２００４年１月２９日木曜日午前９時１５分 Others Screen Display 1 2 3 P 28 27 26 25 24 23 22 21 20 4 5 6 7 ISO100 2560 19 MF H 3x 2 F2.
PAGE 112
LC1-GN.book 112 ページ２００４年１月２９日木曜日午前９時１５分 Others 1 2 3 4 5 1 7 2560 100 _ 0001 1/19 14 13 6 PLAY AUDIO 8 9 10 P F2.8 1/15 ISO100 10:00 1.JAN.
PAGE 113
LC1-GN.book 113 ページ２００４年１月２９日木曜日午前９時１５分 Others The Menu Items ª [REC] mode menu REC 1 2 3 4 SELECT 1 2 3 4 6 7 8 5 6 7 8 9 2/4 OFF EXIT MENU SETUP SELECT SET EXIT MENU SETUP 1/3 REC 14 15 16 17 MONITOR AUTO REVIEW BEEP POWER SAVE OFF 1 2MIN. ON 100 OFF EXIT MENU SELECT OFF 2x FLASH SYNC. PICT.ADJ. MOTION IMAGE 3x 1ST OFF EXIT MENU SETUP 2/3 REC 18 19 20 21 EXIT MENU D.ZOOM (P70) FLASH SYNC. (P71) PICT.ADJ.
PAGE 114
LC1-GN.book 114 ページ２００４年１月２９日木曜日午前９時１５分 Others SETUP 3/3 REC 22 23 24 RESET USB MODE LANGUAGE SELECT Mass Storage ENG SET 33 34 EXIT MENU 22 RESET (P25) 23 USB MODE (P95) 24 LANGUAGE (P25) SELECT • For items without numbers, refer to those with the same name in [REC] mode menu. 25 26 27 28 29 SET 30 31 32 RESIZE TRIMMING FORMAT SET SELECT EXIT MENU ROTATE (P78) PROTECT (P84) DPOF PRINT (P79) SLIDE SHOW (P86) AUDIO DUB.
PAGE 115
LC1-GN.book 115 ページ２００４年１月２９日木曜日午前９時１５分 Others Cautions for Use In the event of abnormal operation (e.g. if the unit emits smoke or an unusual smell), immediately stop operating the unit and consult the Panasonic Customer Care Centre on 132600. ª Optimal Use of the Camera Keep the camera away from magnetized equipment (such as a microwave oven, TV, cell phone, video game equipment, etc.).
PAGE 116
LC1-GN.book 116 ページ２００４年１月２９日木曜日午前９時１５分 Others Do not use benzine, thinner or alcohol for cleaning the camera. • Before cleaning the camera, remove the battery or disconnect the AC adaptor from the electrical outlet. • The camera body may be deformed and the surface finish may peel off. • Wipe the camera with a soft, dry cloth. To remove stubborn stains, wipe with a cloth that is soaked in a detergent diluted with water and afterward finish wiping with a dry cloth.
PAGE 117
LC1-GN.book 117 ページ２００４年１月２９日木曜日午前９時１５分 Others ª Cautions for Storage Before storing the camera, remove the card and the battery. Store all the components in a dry place with a relatively stable temperature. (Recommended temperature: 15oC to 25oC, Recommended humidity: 40% to 60%) Battery • Do not leave the camera and the battery at the place where the temperature is too high, such as inside a car during the summer. • Extremely high or low temperatures will shorten the life of the battery.
PAGE 118
LC1-GN.book 118 ページ２００４年１月２９日木曜日午前９時１５分 Others ª Folder Composition ª Motion Image When a Memory Card with data recorded on it is inserted into a PC, the folders shown below will appear. The auto focus and the aperture value are fixed to the value set when you start the recording (the value set on the first frame). Therefore, the following phenomena may appear. SD Memory Card DCIM 100_PANA EXPORT MISC PRIVATE1 • In the [100_PANA] folder it is possible to record up to 999 pictures.
PAGE 119
LC1-GN.
PAGE 120
LC1-GN.book 120 ページ２００４年１月２９日木曜日午前９時１５分 Others Message Display [NO MEMORY CARD] Insert the card. [NO ADDITIONAL DELETE SELECTIONS CAN BE MADE] You have exceeded the number of pictures that can be set at once with multi-delete setting. [THIS MEMORY CARD IS PROTECTED] Cancel the card lock. [MEMORY CARD ERROR FORMAT THIS CARD?] The format of the card cannot be recognized by this camera. Format the card again with this camera.
PAGE 121
LC1-GN.book 121 ページ２００４年１月２９日木曜日午前９時１５分 Others Troubleshooting 1: The camera is not turned on. 1-1: Are the battery inserted or the AC adaptor correctly connected? Check the connection. 1-2: Is the battery sufficiently charged? Use the battery that has been sufficiently charged. 2: 2: 3: 3: while you press the shutter button halfway. This is not a malfunction. This is caused by adjusting the aperture value. As the camera is turned on, it turns off immediately.
PAGE 122
LC1-GN.book 122 ページ２００４年１月２９日木曜日午前９時１５分 Others 13: The picture does not appear on the television. 13-1: Is the camera connected to the TV correctly? Check it. 13-2: Set the TV to video input mode. 19: 14: 20: When connecting to a PC, pictures cannot be transferred. 14-1: Is the camera connected to the PC correctly? Check it. 14-2: Is the camera recognized by the PC correctly? 14-3: Is the USB mode set correctly? 19: 20: 15: The clock setting is reset.
PAGE 123
LC1-GN.book 123 ページ２００４年１月２９日木曜日午前９時１５分 Others Specifications Digital Camera Power Source: Power Consumption: Camera Effective pixels Image sensor Lens Digital zoom Focus Focus range Shutter system Burst recording Motion image recording ISO sensitivity Shutter speed Metering range White balance Exposure (AE) Metering mode LCD monitor Viewfinder Flash Information for your safety DC 8.4 V 3.0 W (When recording with LCD Monitor) 2.5 W (When recording with Viewfinder) 1.
PAGE 124
LC1-GN.book 124 ページ２００４年１月２９日木曜日午前９時１５分 Others Microphone Speaker Recording media Picture size Quality Recording file format Still Picture Picture with audio Motion images Interface Digital Analogue video/audio Terminal USB AV OUT/REMOTE DC IN Dimensions (WkHkD) Weight Operating Temperature Operating Humidity AUTO, AUTO/Red-eye reduction, Forced ON, Forced ON/Red-eye reduction, Slow sync., Slow sync.
PAGE 125
LC1-GN.
PAGE 126
LC1-GN.
PAGE 127
LC1-GN.
PAGE 128
LC1-GN.book 128 ページ２００４年１月２９日木曜日午前９時１５分 A VQT0H07 F0204Mn0 ( 200A) C Matsushita Electric Industrial Co., Ltd. Web Site: http://www.panasonic.co.