Digital CATV Terminal Operating Instructions Model No. TZ-PCD2000 For assistance, please call : your regional operator (installer) Before connecting, operating or adjusting this product, please read these instructions completely. Save this manual for future reference.
WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock do not remove cover or back. No user-serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons.
Additional Instructions Additional Instructions l Power Sources This product shall be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your Cable operator or Digital CATV Terminal installer or local power company. l Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
Additional Instructions l Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.
FCC STATEMENT FCC INFORMATION Your Digital CATV Terminal is registered with the Federal Communication Commission and is in compliance with CFR47, Parts 15b, FCC Rules and Regulations. Radio Interference This equipment has been tested and found to comply with the limit for a Class B Digital Device in accordance with the specifications in Part 15 of FCC Rules. The rules are designed to provide reasonable protection against radio and television interference in a residential installation.
Dear Panasonic Customer Welcome to the Panasonic Family of customers. We hope that you have many years of enjoyment from your new Digital CATV Terminal. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt also, and note down the model number and serial number of your set in the space provided on the rear cover of these instructions.
Installation ACCESSORIES Check the accessories before installations. l Operating l AC Power Cord Instruction book l Remote Control Unit l Battery for the Remote Control Unit (2×AA (IEC R6) size) Remote Control battery installation Requires two AA batteries. 1. Push the section marked with an arrow while lifting the cover up to open it. 2. Install the batteries as shown in the battery compartment. (Polarity + or - must match the markings in the compartment). 3.
Installation Front and Rear View of the Digital CATV Terminal Front Panel POWER indicator(LED) Volume - Button Channel + Button Volume + Button BYPASS indicator(LED) MESSAGE indicator(LED) Display Power Button Channel - Button Factory use only Remote control signal receptor Factory use only Door Pull the door toward you to open it. Card Slot POWER Turns the Digital CATV Terminal Power On or Off.
Installation Rear Panel VIDEO jacks AUDIO jacks CABLE OUT jack CABLE IN jack DIGITAL AUDIO OUT DATA Port AC Power Input S-VIDEO jack USB(Universal Serial Bus) Port AC Switched Outlet BYPASS option CABLE IN Use to connect Cable Signal from Cable Service Provider. CABLE OUT Use to connect the Digital CATV Terminal to your TV or VCR. VIDEO Use to connect the Digital CATV Terminal to your TV or VCR. S-VIDEO Use to connect the Digital CATV Terminal to your TV with S-VIDEO, or VCR with S-VIDEO.
Installation Cable connection Connect the cable wire to the CABLE IN jack on the rear panel of the Digital CATV Terminal. Incoming signal from the Cable Service Provider Unplug the AC power cord and disconnect all cables attached to the Digital CATV Terminal. Digital CATV Terminal connection to stereo TV and stereo VCR Follow this diagram when connecting the Digital CATV Terminal to a stereo TV and stereo VCR.
Installation Digital CATV Terminal connection to TV and VCR Follow this diagram when connecting the Digital CATV Terminal to a TV and VCR. TV VCR or S-VCR Procedure l Connect the CABLE OUT jack of the Digital CATV Terminal to the ANT IN jack of the VCR, and connect the ANT OUT jack of the VCR to the ANT IN jack of the TV using 75 Ω shielded cable.
Installation Digital CATV Terminal connection to component with Digital Audio Input jack Follow this diagram to connect the Digital CATV Terminal to a component with a Digital Audio Input jack. Dolby Digital AC-3 decoder or 6-Channel Amplifier & Speakers TV Procedure 1 Connect the Digital Audio Cable from the Digital Audio Out jack on the Digital CATV Terminal to the Digital Audio Input jack on the component with the Digital Audio Input jack.
Installation Power ON/OFF Push the POWER button on this unit to turn the set on POWER-ON Power Indicator: Green Power Indicator Press POWER once more to turn off. Power Indicator: Indicator not illuminated ( Please understand the Digital CATV Terminal is not updated when you plug off from AC outlet.) 2 1 1 Press the Remote Control CBL mode button 2 Press the POWER button. Changing the TV input source (Panasonic TV models) 1 2 3 Procedure 1 Press the TV mode button.
Remote Control CBL, TV, VCR, AUX Menu Press to select remote operation. Press to display Settings menu. POWER Info Press to turn ON and OFF. Press to display channel information. Press to move through interactive screen choices. Guide Press to display interactive program guide. SELECT Press to choose interactive screen item. Exit Press to hide interactive screen. Page Press to display Next/Previous screen. A, B, C Fav On-Screen decision buttons Press to view favorite channels.
Remote Control Remote Control Function Key Chart Key Component Function ALL COMPONENTS Component mode selection for remote control ALL COMPONENTS Turn components On and OFF CBL Interactive program guide CBL TV VCR CBL TV VCR AUX Channel information On screen display Program Settings menu ACTION Menu Program mode CBL, TV Exit Menus CBL View favorite channels CBL, TV Up,Down,Left and Right navigation CBL Select CBL Display Next/Previous screen CBL On-Screen decision buttons CBL, TV, VC
Remote Control Remote Control Function Key Chart Key Component Function CBL, TV, VCR Select channel Select code VCR AUX Channel enter Disc CBL TV VCR AUX VOD rewind Punch to VCR Rewind Fast search rev CBL TV VCR AUX VOD play Punch to VCR Play Play CBL TV VCR AUX VOD fast fwd Punch to VCR Fast forward Fast search fwd CBL TV VCR VOD record Punch to VCR record CBL TV VCR AUX VOD stop Punch to VCR Stop Stop CBL TV VCR AUX VOD pause Punch to VCR Pause Pause CBL TV VCR AUX BYPASS TV/VIDEO TV/
Programming the Remote Control The Universal Remote Control can be programmed to operate many manufacturers’components using the component function buttons for TV, VCR, or AUX. Follow the procedures for programming your Remote Control with and without codes for the component. Determine the manufacturer of the component and look in the table for the code. n Programming for TV operation Use the following procedure to program the TV remote control code.
Programming the Remote Control n Programming Without Code If you cannot find the right Code, you can call up all Codes one after the other to search for a Code. POWER button AUX button VCR button LED TV button 1.Turn on the power for the Component to be programmed. 2.Press the mode button (TV, VCR or AUX) for the component to be programmed, and then press the Setup button and hold for 3 seconds (until the visible LED blinks twice). 3.Use the numeric buttons on the remote control to enter “991”.
Programming the Remote Control n Programming for volume control AUX button VCR button LED TV button CBL button The volume adjustment function can be locked so that regardless of whether CBL, TV or VCR mode is active, the volume is adjusted for only one of the modes. (Refer to the table below.) The default setting is TV. When the setting is AUX mode, you can adjust the volume for the AUX component at all times, even if some other mode is currently active.
Programming the Remote Control n Changing button functions The functions of the remote control buttons can be assigned to other buttons. Setting method (Example) Assigning the function of the POWER button in TV mode to the Exit button in VCR mode 1.Press the Setup button and hold for 3 seconds (until the visible LED blinks twice). 2.Use the numeric buttons on the remote control to enter “994”. After this number is entered, the LED on the remote control will flash twice. 3.
Programming the Remote Control Component Codes The Universal Remote Control is capable of operating many component brands after entering a code. Some components may not operate. The Universal Remote Control does not control all features in all models. Codes for TVs (for TV mode) Manufacturer List Manufacturer Set Up No. Manufacturer Set Up No.
Programming the Remote Control Codes for TVs (for TV mode) (continued) Manufacturer List Manufacturer Set Up No. Manufacturer Set Up No.
Programming the Remote Control Codes for VCRs (for VCR mode) (continued) Manufacturer List Manufacturer Set Up No. Manufacturer Set Up No.
Programming the Remote Control Codes for Audio Amp/Tuners (for AUX mode) Manufacturer List Manufacturer Set Up No. Manufacturer Set Up No.
Troubleshooting Symptom Remedy No power Check that the AC power plug is securely plugged into the power outlet. No reception l Check that equipment is connected properly. l Check that the cable wire is connected properly. No picture l Check that equipment is connected properly. l Check if the channel is available. l Make sure the TV power is turned on. l If your setup includes a VCR and/or stereo, make sure you have properly connected them to the Digital CATV Terminal unit.
Specifications Power Source 120 V AC, 60 Hz Power Consumption MAX 0.6 A Operating conditions Temperature : 32 °F-104 °F(0 °C - 40 °C) Humidity: 20 %-80 % (non-condensing) Connection terminals CABLE IN : F connector, 75 Ω CABLE OUT : F connector, 75 Ω VIDEO OUT : RCA pin jack × 2, 1 Vp-p, 75 Ω S-VIDEO OUT : Mini DIN 4-pin , Y:1 Vp-p(75 Ω), C:0.286 Vp-p(75 Ω) AUDIO OUT : RCA pin jack × 2(L-R), 0.
Notes 27
Customer Record The model number and serial number of this product can be found on its rear panel. You should note this serial number in the space provided below and retain this book, plus your purchase receipt, as a permanent record of your purchase to aid in identification in the event of theft or loss, and for Warranty Service purposes.
