UB5838C-PJQXC0259ZA_mst.book 1 ページ 2009年5月26日 火曜日 午後2時59分 Operating Instructions Electronic Board Model No. [Stand (option)] [Wall-mounting] UB-5838C UB-5338C The unit in this picture is UB-5838C. (Stand kit is optional.) Installation Manual Included (for qualified service personnel) • To assemble this unit, please refer to the Installation manual on page 38 through 55. • Before operating this unit, please read these instructions completely and keep them carefully for future reference.
UB5838C-PJQXC0259ZA_mst.book 2 ページ 2009年5月26日 火曜日 午後2時59分 Thank you for purchasing the Panasonic Electronic Board. For optimum performance and safety, please read these instructions carefully. Accessories Check that all of the following items are included with the unit. In the event that an item is missing, please contact your dealer. Q’ty • Markers (Black, Red, Blue) . . . . . . . . . . . 1 each • Eraser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 • Power cord . . . . . . . . . .
UB5838C-PJQXC0259ZA_mst.book 3 ページ 2009年5月26日 火曜日 午後2時59分 Federal Communications Commission Requirements (For United States only) Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
UB5838C-PJQXC0259ZA_mst.book 4 ページ 2009年5月26日 火曜日 午後2時59分 Illegal Duplication It is unlawful to make duplication of certain documents. Duplicating certain documents may be illegal in your country. Penalties of fines and/or imprisonment may be imposed on those found guilty. The following are examples of items that may be illegal to duplicate in your country.
UB5838C-PJQXC0259ZA_mst.book 5 ページ 2009年5月26日 火曜日 午後2時59分 Trademarks • Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • IBM and AT are trademarks of International Business Machines Corporation in the United States, other countries, or both. • SD Logo is a trademark. • All trademarks referred to in this manual are property of their respective companies.
UB5838C-PJQXC0259ZA_mst.book 6 ページ 2009年5月26日 火曜日 午後2時59分 Features The UB-5838C / UB-5338C is a color electronic board. It is possible to output scanned hand-written text/diagrams as follows: ■ Storing on a USB Flash Memory Device Allows scanned hand-written text/diagrams to be stored onto a USB flash memory device.*1 *1 Not all USB flash memory devices are compatible with this unit. ■ Storing on an SD Memory Card Allows scanned hand-written text/diagrams to be stored onto an SD memory card.
UB5838C-PJQXC0259ZA_mst.book 7 ページ 2009年5月26日 火曜日 午後2時59分 Table of Contents Before You Start Page Before You Start For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 • Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UB5838C-PJQXC0259ZA_mst.book 8 ページ 2009年5月26日 火曜日 午後2時59分 For Your Safety To prevent severe injury and loss of life, read this section carefully before using the unit to ensure proper and safe operation of your unit. WARNING CLASS 1 LED PRODUCT The following graphic symbols are used in this Operating Instructions manual. Power and Ground Connection WARNING Denotes a potential hazard that could result in serious injury or death. The power source voltage of this unit is listed on the nameplate.
UB5838C-PJQXC0259ZA_mst.book 9 ページ 2009年5月26日 火曜日 午後2時59分 For Your Safety Ensure that the plug connection is free of dust. In a damp environment, a contaminated connector can draw a significant amount of current that can generate heat and eventually cause fire if left unattended over an extended period of time. Never touch the plug with wet hands. Danger of electric shock exists. Stop operation immediately if the unit emits smoke, excessive heat, abnormal smell or unusual noise.
UB5838C-PJQXC0259ZA_mst.book 10 ページ 2009年5月26日 火曜日 午後2時59分 For Your Safety CAUTION After installing or moving the unit, lock the casters and set the fall-prevention extension legs. Power When the unit is not used over an extended period of time, switch it Off and unplug it. If an unused unit is left connected to a power source for a long period, degraded insulation may cause electric shock, current leakage or fire. The unit should be used only with the power cord that is supplied by the manufacturer.
UB5838C-PJQXC0259ZA_mst.book 11 ページ 2009年5月26日 火曜日 午後2時59分 For Your Safety This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp. fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amps. and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse.
UB5838C-PJQXC0259ZA_mst.book 12 ページ 2009年5月26日 火曜日 午後2時59分 Precautions 12 Installation • Do not install the unit where it may be exposed to direct sunlight, near heating equipment, or near air-conditioning vents as this may cause discoloration of the screen. • Do not install the unit in strong sunlight or strong lighting. Proper copying may become impossible.
UB5838C-PJQXC0259ZA_mst.book 13 ページ 2009年5月26日 火曜日 午後2時59分 Precautions Before You Start Battery If a battery is used improperly, the battery may leak, causing corrosion of the unit, or it may burst. To prevent this, always follow the precautions given below. • Always insert battery with its polarity properly oriented. • If the battery has run out, remove it immediately and dispose of it according to local regulations. Leaving drained battery may result in leakage.
UB5838C-PJQXC0259ZA_mst.
UB5838C-PJQXC0259ZA_mst.book 15 ページ 2009年5月26日 火曜日 午後2時59分 Part Names and Functions Before You Start Control Panel Mode Key Display Advance Key Set-up Key Name Start/Stop Key Description When in standby mode, the display shows the current status of the unit as follows: • The time is shown on the top left corner of the display. • The scanning mode is shown on the icons on the left side of the display. • The destination for scanned images is shown in the center of the display.
UB5838C-PJQXC0259ZA_mst.book 16 ページ 2009年5月26日 火曜日 午後2時59分 Before Using This unit has the following functions concerning information security. Please use them properly. ■ Screen Erase Announce function ■ Operation Password function After scanning the screen, the following display appears to prompt you to erase the text/diagrams on the screen.
UB5838C-PJQXC0259ZA_mst.book 17 ページ 2009年5月26日 火曜日 午後2時59分 Scanning It is possible to output scanned images to a USB flash memory device, SD memory card, external printer, or computer. If multiple output devices are connected to this unit at the same time, the output destination will be selected in the following priority: 1. Computer 2. USB flash memory device 3. SD memory card 4. External printer The current destination is shown on the display.
UB5838C-PJQXC0259ZA_mst.book 18 ページ 2009年5月26日 火曜日 午後2時59分 Scanning • When scanning has finished, a preview of the scanned image is shown on the display. Storing images on a USB flash memory device 1 2 Set the power switch to on ( I ). Connect the USB flash memory device to “USB Connector-A for USB Flash Memory Device”. Note • Do not remove the USB flash memory device until the preview is shown on the display.
UB5838C-PJQXC0259ZA_mst.book 19 ページ 2009年5月26日 火曜日 午後2時59分 Scanning Storing images on an SD memory card 1 2 3 Press the Mode Key scanning mode. 4 Press the Start/Stop Key. Set the power switch to on ( I ). to select the • The unit starts scanning. • The scanning status is shown on the display. Open the SD memory card cover and insert the SD memory card into the SD memory card slot until it is locked. Then close the SD memory card cover. • The SD memory card icon is shown on the display.
UB5838C-PJQXC0259ZA_mst.book 20 ページ 2009年5月26日 火曜日 午後2時59分 Scanning 6 Press the Mode Key ( ). 7 After erasing the written text/diagrams on the screen, press the Mode Key ( ) to return to standby mode. • The Screen Erase Announce is shown on the display. • Only remove the SD memory card once you have returned to standby mode. • To remove the SD memory card, open the SD memory card cover and unlock the SD memory card by pressing it once. Once it is unlocked you may remove it.
UB5838C-PJQXC0259ZA_mst.book 21 ページ 2009年5月26日 火曜日 午後2時59分 Scanning 6 Press the Start/Stop Key. • The unit starts scanning and the image is printed. • The copying status is shown on the display. Scanning to a computer ■ System Requirements Computer IBM® PC/AT® or compatible machine Interface USB 2.0 or USB 1.
UB5838C-PJQXC0259ZA_mst.book 22 ページ 2009年5月26日 火曜日 午後2時59分 Scanning Note • The use of a USB hub is not recommended. We cannot guarantee that the unit will work properly. • Do not connect two or more Panasonic electronic boards to a computer. It may cause the computer operation to become unstable. 3 Press the Mode Key scanning mode. 4 Press the Start/Stop Key. Open the Removable Disk displayed on the computer screen, and click [Refresh] from the [View] in the Windows Explorer window.
UB5838C-PJQXC0259ZA_mst.book 23 ページ 2009年5月26日 火曜日 午後2時59分 Moving the Electronic Board 1 Make sure that the power switch is set to off ( ), and disconnect the power cord on both ends. • Make sure if there are any other devices connected to the unit. If so, disconnect them. 2 Release the lock A and fold back the fallprevention extension legs B as follows: A A B Using 3 Release the caster locks and move the unit. Releasing the lock Note • Always move the unit with 2 people.
UB5838C-PJQXC0259ZA_mst.book 24 ページ 2009年5月26日 火曜日 午後2時59分 Setting the Unit The following settings can be made using the control panel. Note • The item “Setting the number of copies” is displayed at the top of the set-up menu only when the printer is connected. Setting for scanning time display It is possible to select whether the time that an image is scanned is displayed on the image.
UB5838C-PJQXC0259ZA_mst.book 25 ページ 2009年5月26日 火曜日 午後2時59分 Setting the Unit 3 Press the Advance Key ( ) repeatedly to select (On) or (Off). • When the scanning time display is set to “off”, the following screen is displayed. 4 Press the Mode Key ( mode. File format set-up It is possible to select the file format for outputting images to a USB flash memory device, SD memory card or computer. 1 Press the Set-up Key . 2 Press the Set-up Key ( the following item.
UB5838C-PJQXC0259ZA_mst.book 26 ページ 2009年5月26日 火曜日 午後2時59分 Setting the Unit Setting for Full Size Scanning (UB-5838C only) When images are scanned in full size mode, they are stretched and enlarged in order to utilize the entire space of a page. [Regular size] Press the Set-up Key It is possible to set the current time for the unit clock. 1 Press the Set-up Key 2 Press the Set-up Key ( the following item. 3 Press the Advance Key ( . • The set-up screen is displayed.
UB5838C-PJQXC0259ZA_mst.book 27 ページ 2009年5月26日 火曜日 午後2時59分 Setting the Unit Setting the Password 6 2 Press the Set-up Key ( the following item. . • The set-up screen is displayed. 7 • The interval for entering the password can be selected from 15 minutes / 30 minutes / 1 hour / 2 hours / 4 hours / 8 hours. ) repeatedly to select 3 4 Press the Advance Key ( 5 Press the Advance Key ( ) repeatedly to select (Password on) or (Password off).
UB5838C-PJQXC0259ZA_mst.book 28 ページ 2009年5月26日 火曜日 午後2時59分 Setting the Unit Testing the Printer By performing the Test Print feature, it is possible to clean the printer head from this unit when scanned images are not printed correctly (ex. certain areas appear blank). Once the printer head is cleaned, the following pattern will be printed. If the pattern is printed as shown below, the problem has been fixed. If the pattern is not printed as shown below, refer to the manual of the printer for details.
UB5838C-PJQXC0259ZA_mst.book 29 ページ 2009年5月26日 火曜日 午後2時59分 Daily Care and Maintenance Always turn off the power switch and unplug the power plug when cleaning the unit. Cleaning the Screen and the Unit Caring for the Eraser When the erasing surface of the eraser becomes dirty, hold down the sheet under the top sheet with your finger and peel off the dirty sheet (white or gray sheet) by pulling in the direction of the arrow.
UB5838C-PJQXC0259ZA_mst.book 30 ページ 2009年5月26日 火曜日 午後2時59分 Daily Care and Maintenance Replacing the Battery for the unit clock When the clock battery has been drained, the time setup screen is displayed each time the unit’s power is turned on. Replace the battery as follows and set the current time (see page 26). 1 Loosen the screw attached to the lower side of the Control Panel 1, then remove the battery holder 2.
UB5838C-PJQXC0259ZA_mst.book 31 ページ 2009年5月26日 火曜日 午後2時59分 Troubleshooting To identify error message that are displayed on the control panel, refer to “Error Codes” on page 33. The following table lists solutions to problems that you may have concerning this unit as well as tips in avoiding these problems in the future. If problems still persist, call your dealer. Issue Solution and Care See Page The power switch is on but the display is off. Confirm that the power plug is securely plugged in.
UB5838C-PJQXC0259ZA_mst.book 32 ページ 2009年5月26日 火曜日 午後2時59分 Troubleshooting 32 Issue Solution and Care See Page The USB flash memory device, SD memory card, or printer is not recognized. The USB flash memory device, SD memory card, or printer is not supported by this unit. For information regarding available USB flash memory devices, SD memory cards, and printers, refer to the following site: http://panasonic.co.jp/pcc/products/en/eboard/ ub-5838c_info.
UB5838C-PJQXC0259ZA_mst.book 33 ページ 2009年5月26日 火曜日 午後2時59分 Troubleshooting Error Codes The following table describes the meaning of each error code which may appear on the display. Error Code Cause Remedy See Page U103021 ~ U103025 U403021 ~ U403025 The scanner or screen is in strong sunlight or strong lighting. Change the location of the unit or block the light. U403011 U403012 The screen will not move. Turn off the power and slowly move the screen by hand.
UB5838C-PJQXC0259ZA_mst.book 34 ページ 2009年5月26日 火曜日 午後2時59分 Troubleshooting Cause Remedy See Page USB flash memory device writing error occurred. Check whether the USB flash memory device is written normally using a computer. – U306144 SD memory card writing error occurred. Check whether the SD memory card is written normally using a computer. – U407209 USB flash memory device was removed while scanning. Connect the USB flash memory device, then scan again.
UB5838C-PJQXC0259ZA_mst.book 35 ページ 2009年5月26日 火曜日 午後2時59分 Troubleshooting Error Code U306001 U306002 U413209 U413010 U407208 U406208 Cause Remedy See Page SDHC memory card is connected. SDHC memory card is not supported. Use an SD memory card. – Unsupported SD memory card is connected. If an SD memory card has been formatted (ex. by the general formatting software of a computer), it oftentimes cannot be recognized by this unit.
UB5838C-PJQXC0259ZA_mst.book 36 ページ 2009年5月26日 火曜日 午後2時59分 Specifications Model No.
UB5838C-PJQXC0259ZA_mst.book 37 ページ 2009年5月26日 火曜日 午後2時59分 Specifications Model No. Printer Output Block UB-5838C UB-5338C Interface Full Speed USB 2.0 Support printer language PCL 3 GUI Paper size A4/Letter*1 Print resolution 300 dpi Continuous printing 1 to 9 sheets USB Flash Memory Device Output Block Interface Full Speed USB 2.0 Support Format FAT (FAT16)/FAT32 format (Maximum capacity: 32 GB) Store File Format PDF/JPEG SD Memory Card Output Block SD specification Version 1.
UB5838C-PJQXC0259ZA_mst.book 38 ページ 2009年5月26日 火曜日 午後2時59分 Installation Manual (for qualified service personnel) Table of Contents page For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Assembling the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 ● Accessories for assembling. . . . . . . . . . . . . . . . . . . . . . . . . . 40 ● Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UB5838C-PJQXC0259ZA_mst.book 39 ページ 2009年5月26日 火曜日 午後2時59分 For Your Safety To prevent severe injury and loss of life, read this section carefully before using the unit to ensure proper and safe operation of your unit. The following graphic symbols are used in this Installation Manual. WARNING Denotes a potential hazard that could result in serious injury or death. CAUTION Denotes hazards that could result in minor injury or damage to the unit.
UB5838C-PJQXC0259ZA_mst.book 40 ページ 2009年5月26日 火曜日 午後2時59分 Assembling the unit ■ Accessories for assembling The package includes the parts for setting up the unit shown below. Make sure that all of these parts are included in the package before proceeding. No. Part Name Illustration Q’ty Washer 4 For assembling the stand Wall-mounting fixture 2 For wall-mounting Clamp 1 For power cord when using the stand 1 The illustration of the power cord is for the United States.
UB5838C-PJQXC0259ZA_mst.book 41 ページ 2009年5月26日 火曜日 午後2時59分 Assembling the unit ■ Assembly 1 Assemble the wall-mounting fixture or optional stand. 2 Remove the joints and the shipping box. • If you are using a wall-mounting fixture, refer to “Wall-Mounting Construction” on page 48. • If you are using a stand, refer to “Optional Stand Assembly (UE-608035)” on page 53. • UB-5838C has 12 joints. • UB-5338C has 8 joints.
UB5838C-PJQXC0259ZA_mst.book 42 ページ 2009年5月26日 火曜日 午後2時59分 Assembling the unit 3 Collapse the carton box. [Wall-mounting] 5 4 Remove the four rivets. Rivet Remove the protective plastic bag and lay down the unit onto the shipping box with the screen film surface facing downward. Note • To remove the rivets, turn them counterclockwise with a screwdriver. (The fixed part of the rivets will be raised.) 6 Hang the two wall-mounting shafts of the unit to the wall-mounting fixtures.
UB5838C-PJQXC0259ZA_mst.book 43 ページ 2009年5月26日 火曜日 午後2時59分 Assembling the unit 7 After unscrew the 4 screws from the lower center frame cover, remove it. [Optional Stand] 10 Attach the optional stand to the unit. • Each stands has four holes (A, B, C, D). 1) Attach the stand to the unit with the locking caster up.
UB5838C-PJQXC0259ZA_mst.book 44 ページ 2009年5月26日 火曜日 午後2時59分 Assembling the unit 11 Stand the unit up. 12 Attach the rivets (included in the stand) to the holes in the stand that are not already in use. • normal height: 2 places • higher than normal height: 4 places 13 44 Attach the clamp to the stand. • Attach the 3 clamp for the power cord to the upper side of the stand, on the control box side.
UB5838C-PJQXC0259ZA_mst.book 45 ページ 2009年5月26日 火曜日 午後2時59分 Electronic Board Operations Check ■ Before Operation Check ■ Setting the time Set the time as follows. 1 2 Wipe the screen film surface. • Soak a soft cloth with water, wring well, and wipe the screen film surface. 1 Turn the power switch on. Note • Do not wipe the screen film surface with paint thinner, benzene, or cleaners that contain abrasives. Doing so may cause discoloration. • Do not wipe the screen film surface with a dry cloth.
UB5838C-PJQXC0259ZA_mst.book 46 ページ 2009年5月26日 火曜日 午後2時59分 Electronic Board Operations Check ■ Operation Check Procedure After assembling the unit and setting the time, perform the procedures presented in the following table to make sure it functions properly. Points to Check Step 1 2 Turn the power switch on. Press the Advance Key. Condition Solutions The standby message is displayed after the initial message is displayed. (Normal operation) Display does not appear. Check the power cord.
UB5838C-PJQXC0259ZA_mst.book 47 ページ 2009年5月26日 火曜日 午後2時59分 Repacking Perform Assembly Steps 2 through 13 on pages 41 - 44 in reverse to repack the unit and accessories. Use the joints to fasten the shipping box. Note • When handling the screen unit, grasp the side cover on either side of screen. Do not grasp the screen film surface, as this may scratch it.
UB5838C-PJQXC0259ZA_mst.book 48 ページ 2009年5月26日 火曜日 午後2時59分 Wall-Mounting Construction ■ Checking the Wall When mounting on a wall, consult with your building’s owner, caretaker or construction manager to determine if the wall strength is sufficient to install this unit. For safety, install this unit only after thoroughly understanding the type of walls, the appropriate types of screws and the construction method (page 51). Note • Do not attach the electronic board to mortared walls.
UB5838C-PJQXC0259ZA_mst.book 49 ページ 2009年5月26日 火曜日 午後2時59分 Wall-Mounting Construction ■ Installing the Wall-Mounting Fixtures 1 Ensure that the wall is strong enough to support the unit. 2 Using the measuring tape and level, mark the 8 locations to insert the screws. For UB-5838C: 1,373 N [140 kgf (309 lbf)] For UB-5338C: 1,275 N [130 kgf (287 lbf)] UB-5838C: 1,927 mm (6' 3 7/8") UB-5338C: 1,565 mm (5' 1 5/8") 35.5 mm (1 25/64") 35.
UB5838C-PJQXC0259ZA_mst.book 50 ページ 2009年5月26日 火曜日 午後2時59分 Wall-Mounting Construction 4 Install the wall-mounting fixtures using the 4 screws. • 2 screws are used for each wall-mounting plate. The remaining 4 screws are used after installing the unit on the wall. UB-5838C: 1,927 mm (6' 3 7/8") UB-5338C: 1,565 mm (5' 1 5/8") 86 mm (3 25/64" ) Wall-mounting fixture 1,009.
UB5838C-PJQXC0259ZA_mst.book 51 ページ 2009年5月26日 火曜日 午後2時59分 Wall-Mounting Construction ■ Wall Types and Installation Procedures The method for attaching the wall-mounting fixtures to the wall will vary depending on the nature of the wall’s structure. Three available options are listed below. Other methods may be necessary depending on the wall. ● Metal or Concrete walls Stud plugs (sold in stores) are needed. Drill bit Drill eight holes in the wall.
UB5838C-PJQXC0259ZA_mst.book 52 ページ 2009年5月26日 火曜日 午後2時59分 Wall-Mounting Construction ● Plasterboard walls Split-wing toggles (sold in stores) are needed. Split-wing toggle Wall-mounting fixture Plasterboard Bolt Insert the bolt through the hole in the wall-mounting fixture and attach the split-wing toggle. Then insert the split-wing toggle into the hole while the arms are horizontal. For the correct hole size, refer to the instructions for the particular split-wing toggles used.
UB5838C-PJQXC0259ZA_mst.book 53 ページ 2009年5月26日 火曜日 午後2時59分 Optional Stand Assembly (UE-608035) ■ Included Parts Check that the following parts are included with the optional stand (UE-608035). No. Part name 2 Support Beam 2 Fall-prevention Extension Leg 4 Flat Head Screw (M6 × 60 mm [2 3/8"]) 4 Nut 4 Wrench (4 mm [5/32"])*2 1 Support Bracket 2 Spring Washer 4 Screw (M6 × 45 mm [1 25/32"]) 4 Not use with this electronic board (This is used for other models.
UB5838C-PJQXC0259ZA_mst.book 54 ページ 2009年5月26日 火曜日 午後2時59分 Optional Stand Assembly (UE-608035) ■ Assembly Instructions 1 Assemble the fall-prevention extension legs.
UB5838C-PJQXC0259ZA_mst.book 55 ページ 2009年5月26日 火曜日 午後2時59分 Optional Stand Assembly (UE-608035) 3 Pull the fall-prevention extension legs down. 1 2 Note • When folding back the fall-prevention extension legs, release the lock as follows (1, 2). 1 1 4 2 Mount the unit. • Refer to “Assembling the unit” (page 40).
UB5838C-PJQXC0259ZA_mst.book 56 ページ 2009年5月26日 火曜日 午後2時59分 Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.