Operating Instructions Electronic Board (elite Panaboard) Model No. UB-T880W UB-T880W UB-T880 Stand is sold separately. Installation Manual Included (for qualified service personnel) • To assemble this unit, please refer to the Installation Manual on pages 35 through 55. • Before operating this unit, please read these instructions completely and keep them carefully for future reference. • This unit is designed for installation by a qualified servicing dealer.
Introduction Introduction Introduction Thank you for purchasing the Panasonic Electronic Board. For optimum performance and safety, please read these instructions carefully. Feature Highlights By connecting the elite Panaboard to a computer and using a projector to display the contents of the computer’s screen on the elite Panaboard, you can do the following. Touch and Electronic Pen Features • Manipulate objects on the computer screen by using your finger as a mouse.
Introduction For Business • Visually convey your product’s characteristics and create an appealing product presentation by displaying images and using your finger or the electronic pen to highlight key points. • Information projected on the elite Panaboard at your company—including what you add, using your finger or the electronic pen—can be displayed in real-time at remote locations using videoconferencing equipment.
Introduction Help of the Software Instructions for elite Panaboard software and elite Panaboard book (included) are provided in the help information accompanying the software. For details on accessing this information, see “Viewing the Help of the Software” (page 27). Federal Communications Commission and Industry Canada Requirements For United States and Canada Only This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules.
Introduction Warning about saving data When the system storage device or any of its optional storage device is adversely effected by operational errors, static electricity, electrical noise, vibration, dust or when the power has been cut off due to malfunction, repair or inadvertently, the memory contents may be lost or changed. Before operating the system, make a point of reading the precautionary notes in the Operating Instructions and the help information, and observe them during operation.
Introduction For FRG Users (For Germany Only) Note Machine noise information regulation - 3.GPSGV, the maximum sound pressure level is 70 dB(A) or less, in conformity with EN ISO 7779. This device is not intended for use in the direct field of view at visual display workplaces. To avoid incommoding reflexions at visual display workplaces this device must not be placed in the direct field of view.
Table of Contents Table of Contents Table of Contents For Your Safety..........................................................................................8 For Your Safety .................................................................................................................. 8 For Users............................................................................................................................ 8 Safety Information (For United Kingdom only) ...................................
For Your Safety For Your Safety For Users For Your Safety To prevent severe injury and loss of life, read this section carefully before using the unit to ensure proper and safe operation of your unit. • This section explains the graphic symbols used in this manual. WARNING Denotes a potential hazard that could result in serious injury or death. CAUTION Denotes hazards that could result in minor injury or damage to the unit.
For Your Safety Plug the power cord firmly into an AC outlet. Otherwise, it can cause fire or electric shock. Do not pull, bend, rest objects on, or chafe the power cord and plug. Damage to the power cord or plug can cause fire or electric shock. Do not attempt to repair the power cord or plug. If the power cord or plug is damaged or frayed, contact an authorized service representative for a replacement.
For Your Safety Battery Electronic Pen / elite Panaboard Use only the specified type of battery. Using the incorrect type of battery can result in overheating/burning or leakage of battery acid. Make sure that the battery is installed with the correct polarity as indicated on the battery holder. Incorrectly installed batteries may burst or leak, resulting in injuries. Do not use the damaged batteries. Using damaged batteries may result in leaking.
For Your Safety After installing or moving the unit, lock the casters and set the fall-prevention extension legs. CAUTION Power When the unit is not used over an extended period of time, switch it off and unplug it. If an unused unit is left connected to a power source for a long period, degraded insulation may cause electric shock, current leakage, or fire. The unit should be used only with the power cord enclosed with the unit.
For Your Safety Safety Information (For United Kingdom only) This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse.
For Your Safety Precautions Other Information Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. Usage Note About Using the Battery If a battery is used improperly, the battery may leak, causing corrosion of the unit, or it may burst. To prevent this, always follow the precaution given below.
Usage Included Accessories Usage Check that all of the following items are included with your elite Panaboard. In the event that an item is missing, please contact your dealer. List of Accessories Power Cord (3 m [9 ft. 10 1/8 in.]) 1 USB Cable (5 m [16 ft. 4 7/8 in.]) 1 Software DVD-ROM 1 AAA Battery (LR03) (Disposable) 1 Electronic Pen 1 Penpoint (Replacement) 1 Operating Instructions (this document) 1 Warranty 1 2.4 GHz USB Wireless Adaptor* 1 * A 2.
Usage Names and Uses of the Parts Screen Screen Board Detects the position of your finger or the electronic pen. Project the contents of a computer screen using a projector. Power Switch/Power LED (green) Turns the elite Panaboard on or off each time the power switch is pressed. Lights green when the power is on. Error LED (red) Blinks red when an error occurs. Pen Tray Push the center of the door to open the pen tray, which can hold the electronic pen.
Usage Electronic Pen Strap Loop For attaching straps, if desired. (No strap is included. Use a strap from which the cord will detach if excessive force is applied.) Selector Dial Selects features of the electronic pen. Status LED (green) Lights when the electronic pen power is on. Blinks when the electronic pen battery is low. Prepare a new battery and replace the old battery soon. Up Button Performs the same function as pressing the Page Up key on a computer by remote control.
Usage Notice • When the electronic pen and your finger are used simultaneously, the elite Panaboard can not recognize these separately. Wait 1 second or more when changing between your finger and the electronic pen. When changed in a shorter time or when the electronic pen and your finger touch simultaneously, the result is according to which one the elite Panaboard recognized first. • Confirm that the status LED lights when using the electronic pen.
Usage Connecting External Components 1. Connect the power cord (included) to the elite Panaboard, and plug the power cord into an AC outlet. Power Cord (Included) • Plug the power cord into an outlet that is close to the elite Panaboard and in a location that is easy to unplug. • If you are using the optional stand, plug the power cord into the AC inlet, and secure the cord as shown in the illustrations below. When attaching the power cord downward.
Usage 2. Connect the elite Panaboard to a computer using the USB cable (included). • elite Panaboard: Plug the B connector (smaller connector) into the elite Panaboard’s USB port. Computer: Plug the A connector (larger connector) into a USB port on the computer. • Do not connect the elite Panaboard via a USB hub. This could result in erroneous operation. Notice • Do not connect the elite Panaboard to a computer via USB unless elite Panaboard driver/software/ book is installed.
Usage Connecting External Devices 1. Connect the external device to the elite Panaboard using a USB cable (sold separately). • elite Panaboard: Plug the A connector (larger connector) into the elite Panaboard’s USB port. External device: Plug the B connector (smaller connector) into a USB port on the external device. To USB Port USB Cable (Sold Separately) Flatbed Scanner MFP To USB Port About the Usage Location • Do not place the elite Panaboard where it is directly exposed to sunlight.
Usage Volume Control • The volume of the USB speaker on the elite Panaboard can be controlled using the Volume Dial, the volume of Windows, and the volume of the application being used. To adjust the volume, use the Volume Dial, or adjust the volume of the application. Power Switch • After turning the elite Panaboard off, wait more than 2 seconds before turning it back on. Moving the elite Panaboard When Using the Stand (Sold Separately) 1.
Usage Installing the Software 5. Click [Install elite Panaboard] on the “Menu” To install the elite Panaboard driver/software/book, follow the procedure below. 6. If you agree to the terms in the “END-USER Notice • Do not connect the USB cable until the installation is completed. • Do not connect more than 1 elite Panaboard to the same computer. (Doing so can cause erroneous behavior on the computer.) 1. Turn on your computer and start the Windows operating system.
Usage 8. When the following screen is displayed, confirm that the USB cable is not connected to your computer or the elite Panaboard, and click [OK]. • If the USB cable is connected to the elite Panaboard, disconnect the cable, and click [OK]. • If Microsoft® .NET Framework 3.0 (SP 2 or later) or 3.5 (SP 1 or later) is not installed, an installation screen will be displayed. Follow the on-screen directions to install these components. 10. When installation has finished, click [Finish].
Usage Setting the Projector Set up your projector as instructed below. About Positioning the Image • When you are projecting an image, make sure the • If the image is projected trapezoidally, the position may not be read correctly. Adjust the projector so that the projected image is a rectangle. Refer to your projector’s documentation for information on adjusting the projected image. image is inside the screen frame.
Usage Using the elite Panaboard After Positioning the System (Calibration) 3. Calibrate the equipment by using your finger to touch the center of the indicated points following the instructions on the screen for about 2 seconds each. About Calibration Calibration refers to setting up the elite Panaboard and projector so that lines and comments drawn with your finger or the electronic pen are displayed in the correct position. Be sure to perform calibration before use.
Usage Starting the elite Panaboard software When the elite Panaboard software is installed, the icon is displayed in the notification area when calibration is finished, and you can use the elite Panaboard software. • To display the Select Function Menu, click the Menu Start Tab (left side: with your finger. / right side: ) on the screen Starting the elite Panaboard book The elite Panaboard book can be started in the following ways.
Usage Viewing the Help of the Software Follow the procedure below to view the help of the software installed on your computer. 1. Turn on your computer and start Windows. 2. Open “Software Help” from the Start menu. ([Start] → [All Programs] → [Panasonic] → [elite Panaboard] → [Software Help]) • General help information of the installed software is displayed. 3. Open Panasonic Software Update Manager help from the Start menu.
Appendix Daily Care Appendix When cleaning the elite Panaboard or inside the elite Panaboard, make sure to switch off the power and unplug the power cord from the AC outlet. Cleaning the elite Panaboard Replacing the Battery in the Electronic Pen When the electronic pen battery is low, the pen status LED blinks. Continued use of the electronic pen can lead to poor performance. Replace the battery as soon as possible. See “Inserting (Replacing) Batteries” (page 17) for details on replacing the battery.
Appendix Replacing the Penpoint of the Electronic Pen As the penpoint of the electronic pen becomes worn, the penpoint will no longer slide easily across the surface. Continuing to use the electronic pen in this condition may make the screen dirty and cause malfunction. Replace the penpoint with a new one as soon as possible. 1. Remove the penpoint cover. 1 2. Remove the old penpoint and attach the new one. in t po nt n e oi d P enp Ol P w Ne 3. Reattach the penpoint cover.
Appendix Troubleshooting When experiencing problems, please refer to the table below for possible solutions. If the problem persists, contact your dealer. In the case of the kinds of trouble which are not described in the table below, refer to “Troubleshooting” in the software help. Symptom Possible cause and solution See page The LEDs do not light when the power switch is turned on. Check that the power cord is properly plugged in.
Appendix Symptom Possible cause and solution See page • You are using the electronic pen and your finger simultaneously. The electronic pen loses the functions. (Buttons are unresponsive.) (Lines written with the electronic pen are broken or colors change.) • • • • • → While you operate the elite Panaboard with your finger, the electronic pen produces the same result as when touching the elite Panaboard with your finger.
Appendix Specifications Model Number General Electronic Pen Audio Features 32 UB-T880 / UB-T880W Power AC 100 V–240 V, 50 Hz/60 Hz Power Consumption During Operation: 0.5 A (When power is OFF by the power switch: 0.2 W) Operating Environment Temperature: 10 °C to 35 °C (50 °F to 95 °F) Humidity: 30 % to 80 % Storage Environment Temperature: -20 °C to 40 °C (-4 °F to 104 °F) Humidity: 15 % to 80 % Interface USB 2.0 No.
Appendix Model Number UB-T880 External Dimensions: Height × Width × Depth 1,320 mm × 1,657 mm × 117 mm (4 ft. 4 in. × 5 ft. 5 1/4 in. × 4 5/8 in.) Weight 40 kg (88 lbs) Input Unit Screen Board Size: Height × Width 1,175 mm × 1,602 mm (3 ft. 10 1/4 in. × 5 ft. 3 1/16 in.) Interactive Features Effective Area: Height × Width 1,175 mm × 1,567 mm (3 ft. 10 1/4 in. × 5 ft. 1 11/16 in.) (77 in.
Appendix Supplies & Accessories Optional Device Consumables Stand KX-B061 Electronic Pen UE-608026 Stylus Pen UE-608027 Pointer UE-608028 Up / Down Unit UE-608030 Stand Table Unit UE-608031 Short-Throw Arm Unit UE-608032 Penpoint (Replace the penpoint after it has become worn and no longer slides across the surface.) UG-6026 • To purchase separately sold items, contact your dealer.
Installation Manual Installation Manual (for qualified service personnel) Installation Manual • Request assembly of the Electronic Board, stand and wall mounting from your dealer. • Before constructing or installing the elite Panaboard, please read “Installation Manual (for qualified service personnel)” carefully. Panasonic System Networks Co., Ltd. cannot be held responsible for accidents or damage to property resulting from incorrect installation.
Installation Manual Have the unit installed, removed and disposed of only by qualified service personnel. To ensure safe operation the power cord supplied must be inserted into a standard three-prong AC outlet which is effectively grounded (earthed) through the normal wiring. The fact that the equipment operates satisfactorily does not imply that the power point is grounded (earthed) and that the installation is completely safe.
Installation Manual Included Accessories Installation Manual Confirm that the following items are included with the elite Panaboard. No. Part Name Illustration Q’ty Remarks Power Cord (3 m [9 ft. 10 1/8 in.]) 1 The illustration of the power cord is for the United States. The shape of the plug may vary depending on country/area. USB Cable (5 m [16 ft. 4 7/8 in.
Installation Manual No. Part Name Warranty Illustration Q’ty Remarks 1 May not be included depending on country/ area. Notice • Screws (8 count) for wall mounting are not included. Please purchase screws with a size of M6, appropriate for your type of wall (page 42).
Installation Manual Wall Mounting Construction Checking the Wall When mounting on a wall, consult with your building’s owner, caretaker or construction manager to determine if the wall strength is sufficient to install the elite Panaboard. For safety, install the elite Panaboard only after thoroughly understanding the type of walls, the appropriate types of screws and the construction method (page 42). CAUTION Do not attach the electronic board to mortared walls.
Installation Manual Installing the Wall Mounting Plates 1. Ensure that the wall is strong enough to support the elite Panaboard. Rated strength: greater than 1,962 N (200 kgf) 2. Using the measuring tape and level, mark the 8 locations to insert the screws. UB-T880 421.8 mm (1 ft. 4 19/32 in.) 208.2 mm (8 3/16 in.) 813 mm (2 ft. 8 in.) 40 mm (1 9/16 in.) 1,006 mm (3 ft. 3 19/32 in.) 324.2 mm (1 ft. 49/64 in.) 23.5 mm (15/16 in.) 220.9 mm (8 11/16 in.) UB-T880W 543.3 mm (1 ft. 9 3/8 in.) 208.
Installation Manual 4. Install the wall mounting plates using the 4 screws. • 2 screws are used for each wall mounting plate. The remaining 4 screws are used after installing the elite Panaboard on the wall (page 50). UB-T880 / UB-T880W 813 m m (2 ft . 8 in.) 40 mm (1 9/16 in.) 1 1,006 mm (3 ft. 3 19/32 in.) 23.5 m m ( 15/16 in.) 220.9 m (8 11/1 m 6 in.) • Screws (8 count) are not included with the elite Panaboard. Please purchase screws with a size of M6, appropriate for your type of wall.
Installation Manual Wall Types and Installation Procedures The method for attaching the wall mounting plates to the wall will vary depending on the wall’s structure. Three available options are listed below. Other methods may be necessary depending on the wall. Metal or Concrete walls Stud plugs (not included) are needed. Drill bit Drill 8 holes in the wall. For the correct hole size, refer to the instructions for the particular stud plugs used.
Installation Manual Plasterboard walls Split-wing toggles (not included) are needed. Split-wing toggle Wall mounting plate Plasterboard Bolt Arms Arms Insert the bolt through the hole in the wall mounting plate and into the hole in the wall so that the arms of the split-wing toggle are horizontal. For the correct hole size, refer to the instructions for the particular split-wing toggles used.
Installation Manual Stand KX-B061 Assembly (Sold Separately) Included Parts Check that the following parts are included with the stand KX-B061. No. Part Name Illustration Stand Base 2 Support Beam 2 Cross Bar (A) 2 Cross Bar (B) 1 Screw (M6 × 45 mm [1 3/4 in.]) 10 Two-wing Bolt (M5 × 12 mm [1/2 in.])*1 2 Support Bracket 2 Fall-prevention Extension Leg 4 Screw (M6 × 60 mm [2 3/8 in.
Installation Manual CAUTION Before assembly, be sure to lock the casters. Locking the casters (Push to lock) 1 Assembly Instructions 1. Assemble the fall-prevention extension legs.
Installation Manual 2. Assemble the stand. Assemble with the holes toward the front. Locking caster side (rear) FRONT REAR Locking caster side (rear) Notice • Do not over-tighten the screw (5). (Doing so can warp the support beams.) • Assemble the stand so that the locking casters are on the rear side.
Installation Manual 3. Pull the fall-prevention extension legs down. 1 2 Note • When folding back the fall-prevention extension legs, release the lock as follows (1, 2). 1 1 1 2 4. Mount the elite Panaboard. • See “Assembling the elite Panaboard” (For Mounting on a Stand KX-B061 (Sold Separately) → page 52).
Installation Manual Assembly Instructions Preparing for Removing the elite Panaboard from Its Packaging Remove the 10 joints, open the box, remove the accessory box & packing foam and open the plastic sheet of the elite Panaboard. Shipping Box [Accessory Box Contents] Cushioning material Electronic Board • Power Cord ......................... 1 • USB Cable .......................... 1 • DVD-ROM........................... 1 • Wall Mounting Plate (Right, Left) ..............1 (Each) • Battery...........
Installation Manual Assembling the elite Panaboard For Wall Mounting 1. Attach the power cord. • Connect the power cord to the elite Panaboard 3. Remove the push-turn rivets (4) on the fasteners on the bottom of the board. • Turn the push-turn rivets counter-clockwise with a Phillips-head screwdriver. When the fastener pops up, the part can be removed. before installing on a wall. Power Cord 2. Depending on the location of the outlet, install the power cord as illustrated in the following diagrams.
Installation Manual 5. Remove the screws on each end of the bottom of the lower frame cover. • UB-T880: 2 screws, UB-T880W: 4 screws (UB-T880 is shown in the following figure as an example.) 6. Open the pen tray, remove the screw caps and the screws, and remove the lower frame cover. • Open the pen tray (1), and remove the right and left screw caps (2 locations). Then, remove the screws, and remove the lower frame cover (2).
Installation Manual 10. Turn off the power switch and unplug the power cord from the AC outlet. 11. Wipe the screen board surface. • Gently wipe the screen board surface with a soft, moist cloth. 1 Notice • Do not use thinner, benzene, or abrasive chemicals to clean. (Doing so can result in discoloration.) • Do not wipe the screen board with a dry cloth. (Doing so can cause static electricity buildup.
Installation Manual For Mounting on a Stand KX-B061 (Sold Separately) 3. Hang the elite Panaboard on the stand with the screw heads. 1. Attach the power cord. • Connect the power cord to the elite Panaboard before installing on the stand. Power Cord 2. Depending on the location of the outlet, install the power cord as illustrated in the following diagrams. • When attaching the power cord downward. 4. Secure the elite Panaboard to the stand frame using the two-wing bolts (M5 × 12 mm [1/2 in.
Installation Manual • When installing the elite Panaboard on the stand, you can adjust its height to 4 different levels. When changing the height, remove the left and right screws from the back of the elite Panaboard, and securely insert them at the desired height. Torque (greater than 1 N•m [10 kgf•cm (9 lbf•in.)]). elite Panaboard Height Screw Position -100 mm (-3 7/8 in.) Highest Standard 2nd from top +100 mm (+3 7/8 in.) 2nd from bottom +200 mm (+7 7/8 in.) Lowest 1 5.
Installation Manual Confirming the elite Panaboard Operation After assembling the elite Panaboard, confirm that it operates properly by following the procedure below. Checkpoints Action Operation 1 Turn on the power. Measure Power LED (green) lights. (Normal operation) Power LED (green) does not light, or Error LED (red) is blinking. Check the power cord. See step 1 of “Assembling the elite Panaboard”.
Installation Manual Repackaging To repackage the elite Panaboard, perform steps in the following “Assembling the elite Panaboard” in reverse. • For Wall Mounting → page 49 • For Mounting on a Stand KX-B061 (Sold Separately) → page 52 Package the unit as depicted in the diagram in “Preparing for Removing the elite Panaboard from Its Packaging” (page 48). Notice • When handling the electronic board, hold it by the edge frame and not the screen board. (Holding the screen board can result in damage.
Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.