Operating instructions

ManualsBrandsPanasonic ManualsFor HomeWHSXC12D6E5

HRVATSKI

ENGLISH

• It is strongly recommended to contact the nearest authorized dealer to change the water temperature range.

• Using the control panel could set the temperature range for water outlet temperature and outdoor ambient temperature.

SYSTEM SETTING MODE

SET

SELECT

CANCEL

SETTING

TIMER OUTDOOR

HEAT

SETTING

STATUS

PUMPDW

BOOSTER

QUIET

TANK

WATER OUTLET

HEATER

OPERATION

FORCE

HEATER

ACTUAL

COOL

Operation Mode Temperature display

SETTING indicator

Parameter *

1. Press

SET

for 5 seconds to enter “SETTING” mode. “SETTING” indicator is ON.

2. Press

or to choose a parameter.

3. After selecting the desired parameter, press

SELECT

to enter the parameter.

4. Press

or to set the desired temperature.

5. Press

SET

again to con rm the setting.

• Repeat steps 2 to 5 to set other parameters.

Operation

Mode

Parameter * Description

HEAT

Low outdoor ambient set temperature

(-15°C ~ 15°C).

HEAT

High outdoor ambient set temperature

(-15°C ~ 15°C).

HEAT

Water outlet set temperature at low

outdoor ambient temperature (25°C ~ 55°C).

HEAT

Water outlet set temperature at high

outdoor ambient temperature (25°C ~ 55°C).

HEAT

OFF

Set temperature for turning OFF heating operation (5°C ~ 35°C).

HEATER

Outdoor ambient set temperature for turning ON heater operation (-15°C ~ 20°C).

COOL

Water set temperature during cool mode (5°C~20°C)

TANK

Sanitary tank set temperature (40°C ~ 75°C).

WATER TEMPERATURE THERMO SHIFT SETTING

1. Press

SET

within 5 seconds.

• Repeat steps 3 to 5 to set the desired shift temperature (-5°C ~ 5°C).

Notes:

• Press

or wait 30 seconds to exit “SETTING” mode.

• The setting temperature will be stored in the system once con rm.

• “SETTING” mode cannot be activated when the “PUMPDW” and “STATUS” indicator is ON.

ADVANCE OPERATION

Water Temperature

Outdoor Temperature

• Snažno se preporučuje kontaktiranje ovlaštenog dobavljača da bi se promijenio raspon temperature vode.

• Korištenjem upravljačke ploče moguće je postaviti raspon temperature za izlaz za vodu i vanjsku okolinu.

NAČIN PODEŠENJA SUSTAVA

1. Pritisnite i držite 5 sekundi gumb da biste unijeli način "SETTING". Uključen je pokazatelj "SETTING" (postavka).

2. Pritisnite ili da biste odabrali parametar.

3. Nakon što odaberete željeni parametar, pritisnite da biste unijeliparametar.

4. Pritisnite ili da biste postavili željenu temperaturu.

5. Ponovno pritisnite da biste potvrdili postavku.

• Ponovite korake od 2 do 5 da biste postavili druge parametre.

Način

rada

Parametar * Opis

GRIJANJE

Postavljena niska vanjska temperatura

(-15 °C ~ 15 °C).

GRIJANJE

Postavljena visoka vanjska temperatura

(-15 °C ~ 15 °C).

GRIJANJE

Postavljena temperatura izlaza za vodu pri niskoj

vanjskoj temperaturi (25°C ~ 55°C).

GRIJANJE

Postavljena temperatura izlaza za vodu pri

visokoj vanjskoj temperaturi (25°C ~ 55°C).

GRIJANJE OFF Postavka temperature za radnu aktivnost grijanja OFF (5°C ~ 35°C).

GRIJAČ Postavka vanjske temperature za radnu aktivnost grijanja ON (-15°C ~ 20°C).

HLAĐENJE Postavljena temperatura vode tijekom hlađenja (5°C ~ 20°C).

SPREMNIK Temperatura sanitarnog spremnika (40°C ~ 75°C).

POSTAVKE TERMALNOG POMAKA TEMPERATURE VODE

1. Pritisnite na 5 sekundi.

• Ponovite korake od 3 do 5 da biste postavili željeni temperaturni pomak (-5°C ~ 5°C).

Napomene:

• Pritisnite ili pričekajte 30 sekundi za izlaz iz načina "SETTING".

• Temperatura se pohranjuje u sustavu jednom kada je potvrdite.

• Nije moguće aktivirati način "SETTING" kada su uključeni pokazatelji "PUMPDW" (Crpka ugašena) i "STATUS" (Status).

NAPREDNI RAD

Način rada

BASIC OPERATION

OFF

TO TURN ON OR OFF THE UNIT

• When unit is ON, operation LED is lit and the actual

temperature for water outlet and outdoor ambient are

shown on the control panel display.

MODE

TO SELECT OPERATION MODE

HEAT HEAT +TANK TANK

• HEAT MODE

- To turn ON or OFF the panel/ oor heating operation.

- In this mode, the outdoor unit will provide heating

capacity to the indoor unit.

• HEAT + TANK MODE

- In this mode, the outdoor unit will provide heating

capacity to the sanitary tank and indoor unit.

- This operation is not used when the sanitary water

tank is not installed.

• TANK MODE

- To turn ON or OFF the sanitary tank operation.

- In this mode, the outdoor unit will provide heating

capacity to the sanitary tank.

QUIET

TO ENJOY QUIET ENVIRONMENT

• This operation reduces outdoor unit noise. In this

condition, it may cause decrease in heating capacity.

HEATER

TO ENABLE THE BACKUP

HEATER

• The backup heater provides extra heating capacity

during cold outdoor temperature and only can operated

at heat mode operation for indoor unit when he was

enabled by pushing this button.

• The backup heater will automatically turn ON when the

setting conditions is ful lled.

• To disabled the Heater operation manually, press the

respective button again.

STATUS

CHECK

SYSTEM STATUS CHECK MODE

1. Press

CHECK

for 5 seconds to enter STATUS mode.

2. Press

or to check the Water Inlet

Temperature, Tank Temperature, Compressor Running

Frequency or Error History.

• Press

to exit STATUS mode.

• Once STATUS mode is entered, “STATUS”

indicator is ON.

• STATUS mode cannot be activated when the

“SETTING” indicator is ON.

•

It is strongly recommended to contact the nearest

authorized dealer to change the water temperature range.

• Using the control panel could set the temperature

range for water outlet temperature and outdoor ambient

temperature.

SYSTEM SETTING MODE

SET

SELECT

CANCEL

SETTING

TIMER OUTDOOR

HEAT

SETTING

STATUS

PUMPDW

BOOSTER

QUIET

TANK

WATER OUTLET

HEATER

OPERATION

FORCE

HEATER

ACTUAL

Operation Mode Temperature display

SETTING indicator

Parameter *

1. Press

SET

for 5 seconds to enter “SETTING” mode.

“SETTING” indicator is ON.

2. Press

or to choose a parameter.

3. After selecting the desired parameter, press

SELECT

to enter

the parameter.

4. Press

or to set the desired temperature.

5. Press

SET

again to con rm the setting.

• Repeat steps 2 to 5 to set other parameters.

Operation

Mode

Parameter * Description

HEAT

Low outdoor ambient set temperature

(-15°C ~ 15°C).

HEAT

High outdoor ambient set temperature

(-15°C ~ 15°C).

HEAT

Water outlet set temperature at low outdoor

ambient temperature (25°C ~ 55°C).

HEAT

Water outlet set temperature at high outdoor

ambient temperature (25°C ~ 55°C).

Water Temperature

Outdoor Temperature

HEAT

OFF

Set temperature for turning OFF heating

operation (5°C ~ 35°C).

HEATER

Outdoor ambient set temperature for turning

ON heater operation (-15°C ~ 20°C).

TANK

Sanitary tank set temperature

(40°C ~ 75°C).

WATER TEMPERATURE THERMO SHIFT SETTING

1. Press

SET

within 5 seconds.

• Repeat steps 3 to 5 to set the desired shift temperature

(-5°C ~ 5°C).

Notes:

• Press

or wait 30 seconds to exit “SETTING” mode.

• The setting temperature will be stored in the system once

con rm.

• “SETTING” mode cannot be activated when the

“PUMPDW” and “STATUS” indicator is ON.

ADVANCE OPERATION

Temperatura vode

Vanjska temperatura

Parametar *

Prikaz temperature

Pokazatelj SETTING (postavke)