WJ-FS409 WJ-FS416 FRANÇAIS Model No. ENGLISH Operating Instructions DEUTSCH Video Multiplexer POWER ON Video Multiplexer WJ-FS 409 OFF Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
ENGLISH VERSION We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/89/336. Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC ja 89/336/EE. säädöksiä.
PREFACE .................................................................................................................................................... 4 FEATURES .................................................................................................................................................. 4 PRECAUTIONS ...........................................................................................................................................
PREFACE The WJ-FS409 and WJ-FS416 are Colour Video Multiplexers designed for use in surveillance security systems combined with cameras, alarm sensors, a Time Lapse VTR, two video monitors and a PC. Spot pictures and image sequences of multiple cameras can be monitored simultaneously on two video monitors. Multiscreen pictures and the Multiscreen sequence pictures can be displayed on Multiscreen monitors.
PRECAUTIONS • Refer all work related to the installation of this product to qualified service personnel or system installers. • Do not block the ventilation opening or slots on the cover. To prevent the appliance temperature from rising, place the appliance at least 5 cm (2 inches) away from the wall. • Do not drop metallic parts through slots. This could permanently damage the appliance. Turn the power off immediately and refer servicing to qualified service personnel.
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ■ Front View t SPOT MULTISCREEN POWER ALARM ON ALARM MULTI SCREEN RESET SELECT SWITCH PROTECTER STILL CAMERA SELECT MENU SEQ 1 OFF 2 3 4 5 6 7 8 EL-ZOOM FS 9 VTR CAM 9 ESC Video Multiplexer WJ-FS SET 409 t ALARM POWER CAMERA SELECT SPOT MULTISCREEN STILL 1 ON SWITCH PROTECTER OFF ALARM MULTI SCREEN RESET SELECT 2 3 4 5 6 7 MENU 9 10 11 12 13 14 15 ESC Note: To prevent that the power of the
The 4A screen is a compressed picture of channels 1 through 4, the 4B of channels 5 through 8, the 4C of channels 9 through 12, and the 4D of channels 13 through 16. The 9-segment screen shows the pictures of channels 1 through 9 in a 3x3 pattern. t Spot/Multiscreen Selection Button (SPOT/MULTISCREEN) This button is used to select either the Spot output or Multiscreen output. y Sequence Button (SEQ) This button activates the sequence mode.
■ Rear View i o !0 9 8 7 6 5 4 3 2 1 IN ALARM/REMOTE CAMERA SW IN DATA SIGNAL GND OUT 9 8 7 6 5 4 3 2 1 VIDEO PLAY IN MULTI REC OUT SCREEN OUT SPOT OUT u !1 i o !0 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 IN ALARM/REMOTE DATA CAMERA SW IN SIGNAL GND OUT 16 15 14 13 12 11 10 9 8 VIDEO 7 6 5 4 3 2 1 PLAY IN MULTI REC OUT SCREEN OUT SPOT OUT u !1 q Video Input Connectors (VIDEO IN) These connectors accept a composite vide
SETUP MENU In the SETUP menu you can set preferences for ALARM, MONITOR, REC OUT, SEQUENCE and SYSTEM to meet your requirements. ● Displaying the SETUP menu 1. Confirm that the camera and peripherals are connected correctly and securely. 2. Turn on the power switches of all system components. 3. Press the MENU/ESC button for 2 seconds or more. The SETUP menu appears on the monitor as shown below. • The following buttons are used in the SETUP menu: C: Moves the cursor downward. D: Moves the cursor upward.
■ Setup Menu As shown below, the SETUP menu has five main submenus: Alarm Setup, Monitor Output Setup, Record Output Setup, Sequence Setup and System Setup. All of these submenus are further divided into additional submenus.
■ Alarm Setup Menu GROUP SETUP WJ-FS416 SETUP ALM ALM ALM ALM ALM ALM ALM ALM ALM ALARM SETUP MONITOR OUTPUT SETUP REC OUTPUT SETUP SEQUENCE SETUP SYSTEM SETUP 1 2 3 4 5 6 7 8 9 → → → → → → → → → CH 1 2 3 4 5 6 7 8 9 CH ---------- CH ---------- CH ---------- Move the cursor to ALARM SETUP on the SETUP menu, then press the SET button. The ALARM SETUP menu appears on the monitor screen as shown below.
Notes: • If set to EXT, make sure that the CAMERA SW IN terminal on the rear panel is connected to the Time Lapse VTR. • Depending on the mutual timing between the alarm trigger and the field rate, the initial picture recorded after an alarm is activated may not be related to the alarm. 3. AUTO RESET This item lets you set the time the Video Multiplexer retains the alarm mode before automatic resetting to non-alarm mode.
9. MLT OUT MODE ■ Monitor Output Setup Menu This item lets you select whether to switch the multiscreen output monitor screen automatically to the camera picture of the channel whose alarm is activated. 1. MULTI OUTPUT WJ-FS416 SETUP 1. Move the cursor to the MLT OUT MODE parameter. 2. Select OFF or SPOT by pressing the + or – button. The initial factory setting is SPOT. OFF: Ignores alarm activation and continues to display the pictures in the mode selected previously.
1-3. BORDER ■ Record Output Setup Menu This item lets you select the colour of the border that splits the multiscreen output pictures in a Multiscreen display. WJ-FS416 SETUP 1. Move the cursor to the BORDER parameter. 2. Select the desired mode or colour by pressing the + or – button. The initial factory setting for the border colour is WHITE. WHITE: GREY: BLACK: OFF: ALARM SETUP MONITOR OUTPUT SETUP REC OUTPUT SETUP SEQUENCE SETUP SYSTEM SETUP White Border Grey Border Black Border No border 1-4.
2. REC MODE ■ Sequence Setup Menu This item lets you select the time interval (field rate) for switching the camera channel of the REC OUT signal. When REC MODE is set to EXT, the timing is controlled by the connected VTR. When 004 - 255 (INT) is selected, the timing corresponds to the field rate set here. The parameter settings for different VTR models are shown in the ADDENDUM. 1. MULTI OUTPUT WJ-FS416 SETUP ALARM SETUP MONITOR OUTPUT SETUP REC OUTPUT SETUP SEQUENCE SETUP SYSTEM SETUP 1.
1-2. SEQ MODE This item lets you select the Sequence pattern for display on the Multiscreen monitor. 1. Move the cursor to the SEQ MODE parameter. 2. Select the desired Sequence mode or dwell time by pressing the + or – button. The initial factory setting is QUAD. QUAD: Pictures are displayed on a quad screen in the selected sequence mode and dwell time. Note: In the 9-channel pattern of WJ-FS409, channels 1 - 8 are displayed on two quad screen pages. Channel 9 is not displayed.
■ System Setup Menu 2. SPOT OUTPUT 2-1. AUTO SKIP This item lets you enable or disable the Auto Skip function to skip any steps where no video signal is present at the Spot output. Proceed as described in MULTI OUTPUT, 1-1. AUTO SKIP on page 15. WJ-FS416 SETUP ALARM SETUP MONITOR OUTPUT SETUP REC OUTPUT SETUP SEQUENCE SETUP SYSTEM SETUP 3. MLT/SPT SEQ SETUP This item lets you program or edit a Multi or a Spot Sequence. Up to 9 (16) steps can be assigned in the SPOT SEQ SETUP menu.
2. TITLE POSI This item lets you select the position on the monitor where the camera title is displayed. The initial factory setting places the title at the bottom centre of the monitor screen. TITLE SETUP MENU CH 1 2 3 4 5 6 7 8 9 TITLE 1······· 2······· 3······· 4······· 5······· 6······· 7······· 8······· 9······· 1. Move the cursor to TITLE POSI parameter, then press the SET button. The position setting menu appears on the monitor screen. 2.
ON: Enables the PLAYBACK AUTO mode. OFF: Disables the PLAYBACK AUTO mode. 5. PASSWORD This item lets you select whether to permit free or limited access to the Setup menus. When PASSWORD is set to ON, the operator must enter the password to access the menus. 1. Move the cursor to the PASSWORD parameter. 2. Select ON or OFF by pressing the + or – button. The initial factory setting is OFF. 5-1. Password registration Enter a 4-digit password consisting of numbers from 1 to 9 (except 0).
8. COMMUNICATION SETUP This item lets you set the parameters for the Video Multiplexer to communicate with the appliances linked to the RS-485 chain. Camera numbers also need to be specified since the system can comprise tens of units with 16 or 9 cameras connected to each. 3. Repeat step 2 until each camera has been assigned a unique number. COMMUNICATION SETUP UNIT ADDRESS CAM NUMBER BAUD RATE DATA BIT PARITY CHECK STOP BIT WAIT TIME ALARM DATA 2.
9. ENCODE This item lets you adjust parameters for playing back tapes that are recorded on a Panasonic system or a nonPanasonic system. 1. Move the cursor to the ENCODE parameter. 2. Select PANA or OTHERS by pressing the + or – button. The initial factory setting is PANA. Playback of Tapes Recorded with Other Multiplexer Systems The following settings are necessary to play back video tapes recorded with multiplexer systems of other manufacturers. SYSTEM SETUP ENCODE SW INTERVAL NO.
INSTALLATIONS ■ Mounting in the Rack 1. Remove the four rubber feet by removing the four screws on the bottom of the video multiplexer. 3. Install the video multiplexer with the rack mounting brackets in the rack by using four screws (not included). Remove 4 rubber feet 2. Place the rack mounting brackets on both sides of the video multiplexer and tighten with the six supplied screws (M3 x10).
SYSTEM CONNECTIONS ■ Basic System Connection The Video Multiplexers WJ-FS409 and WJ-FS416 are connected with cameras, video monitors and a Time Lapse VTR. A typical connection example is shown below. The ALARM/REMOTE connector is described later.
■ Connection with the Time Lapse VTR Connect the time lapse VTR as shown in the example below.
■ Connection of the Digital Disk Recorder (Example: WJ-HD100) to a Video Multiplexer Connect the Digital Disk Recorder as shown in the example below.
■ Connection with the Monitors Connect the Monitors to the Spot Output (SPOT OUT) Connector and Multiscreen Output (MULTISCREEN OUT) Connector on the rear of the Video Multiplexer. If the cable is locally procured, make sure it is data grade cable suitable for RS-485 communication. A 2wire twisted pair shielded cable, BELDEN 9406 or equivalent should be used. Pin assignments and data flow are shown below. No.
■ ALARM/REMOTE Connector This 25-pin connector connects alarm related control signals and/or remote switch inputs depending on the status of pins #5 and #22. The tables below show the pin assignment for the WJ-FS409 and WJ-FS416, respectively.
■ Connection with the Alarm Sensors ■ Connection with the Alarm Output Connect alarm sensors to the ALARM/REMOTE connector. As shown in the tables on page 27, the WJ-FS409 accepts up to 9 sensors and the WJ-FS416 up to 16. The sensors should meet the following specifications: 1. Allowable input voltage: Non-voltage contact, or 0 V to 5 V DC 2. Input definition: Specified by ALM INPUT settings, N.O. (Normally Open/Low active) or N.C. (Normally Closed/High active) 3.
■ Connection with the Remote (External) Switches Remote SW1 Function 2 Open or +5V SEQUENCE The Video Multiplexer can be remote controlled if external switches (locally procured) are connected to the ALARM/REMOTE connector. Remote switches, except SEQUENCE, are grouped under Remote SW1 and SW2. For more information refer to the pin assignment tables on page 27.
OPERATING PROCEDURES ■ Monitoring the Camera Picture Example of spot camera picture sequence ● SPOT OUT 1. Spot Picture 1. Press a SPOT/MULTISCREEN button so that the LED of SPOT/MULTISCREEN button lights up. Camera 3 Picture SPOT MULTISCREEN 2. Press a CAMERA SELECT button to display a camera picture on the monitor screen. The LED on the pressed CAMERA SELECT button lights up. Camera 6 Picture 2. To cancel a sequence, press the respective CAMERA SELECT button.
● MULTISCREEN OUT Example of spot camera picture sequence 1. Spot Picture 1. Press a SPOT/MULTISCREEN button so that the LED of SPOT/MULTISCREEN button goes off. Camera 3 Picture SPOT MULTISCREEN 2. Confirm that the LED on the VTR/CAM button is not lit. If the LED is lit, press the VTR/CAM button so that the VTR/CAM indicator goes off. Camera 6 Picture VTR CAM 3. Press a CAMERA SELECT button to display a camera picture on the monitor screen. The LED on the pressed CAMERA SELECT button lights up.
3. Still Spot Picture The following function is available in MULTISCREEN OUT picture only. 1. Repeat the procedures described above for Spot Picture. 2. Press the STILL button to freeze the displayed picture. The LED on the STILL button lights up, and the LED on the pressed CAMERA SELECT button starts to blink. The camera title and “STILL” (both blinking) alternate in the display. 3. To cancel the still picture, press the STILL button again.
5. Multiscreen Picture 1. Press a SPOT/MULTISCREEN button so that the LED of SPOT/MULTISCREEN button goes off. SPOT MULTISCREEN 2. Confirm that the LED on the VTR/CAM button is not lit. If the LED is lit, press the VTR/CAM button so that the VTR/CAM indicator goes off. 4.
■ Recording on the Time Lapse VTR Confirm the parameters on the REC OUTPUT SETUP menu. See page 14 for details. Note: When EXT is selected but no camera switching signal is supplied, time lapse recording will not work properly. In this case, supply the camera switching signal or set REC MODE to 004 (INT) for normal recording. ■ Monitoring the Playback Picture Playback picture is only displayed in MULTI OUTPUT. Caution: Set the time lapse VTR to the playback mode.
3. Press the SPOT/MULTISCREEN button so that the LED of SPOT/MULTISCREEN button goes off. 4. Press a CAMERA SELECT button to display a camera playback picture on the monitor screen. The LED on the pressed CAMERA SELECT button lights up, and the selected playback picture appears on the monitor. 3. Zoomed Spot Playback Picture 1. Repeat the procedures described above for Spot Playback Picture. 2. Press the EL-ZOOM button to display the zoomed picture. The “+” sign appears in the picture.
4. Multiscreen Playback Picture 5. Still Multiscreen Playback Picture 1. Operate the VTR in playback mode. 2. Confirm that the LED on the VTR/CAM button is lit. If the LED is not lit, press the VTR/CAM button so that the LED on the VTR/CAM button lights. 3. Press the SPOT/MULTISCREEN button so that the LED of SPOT/MULTISCREEN button goes off. 4. Press the MULTISCREEN SELECT button to select multiscreen pattern (4-, 9- or 16-segment screen). Note: 16-segment screen is not available for WJ-FS409. 1.
ALARM CONTROL FUNCTION ■ Alarm Input PRI is specified in the ALARM SETUP menu. The Video Multiplexer can handle the following alarms: 2. Alarm Only Mode • Interface Alarm Alarm received from the ALARM/REMOTE connector. “ALARM” is displayed on the monitor screen. • Camera Switching Signal Loss Alarm Alarm indicating that camera switching signal loss has occurred. “SW LOSS” is displayed on the monitor screen. • Video Input Signal Loss Alarm Alarm indicating that camera signal loss has occurred.
2. Alarm Channel Monitor Mode The picture of the channel where alarm is activated is displayed on the monitor if Alarm MLT OUT MODE is set to SPOT. The picture displayed before alarm was activated will be restored after the alarm is reset. It remains on the monitor if Alarm MLT OUT MODE is set to OFF. ■ Alarm Reset ● Manual Reset When an alarm is activated, the ALARM Indicator blinks. The indicator keeps blinking until all alarms are cleared by pressing the ALARM RESET button.
OTHER FUNCTIONS ■ Camera Switching Pulse Loss Display • When loss of the camera switching pulse is detected, “SW LOSS” will blink on the monitor screen. • The buzzer does not beep. • When the camera switching pulse is recovered, “SW LOSS” is cleared from the monitor. ALL RESET The Video Multiplexer WJ-FS409 (WJ-FS416) can be reset to the initial factory settings as follows. 1. Turn off the Power Switch. 2. Turn on the Power Switch (;) while pressing the and buttons (WJ-FS409) or , and buttons (WJ-FS416).
APPENDIX This appendix details the elements for communication between the Video Multiplexers and the System Controller. For BAUD RATE, DATA BIT, PARITY CHECK, STOP BIT and WAIT TIME, see page 20 COMMUNICATION SETUP menu. ● Communication Protocol Data Format Code [STX] [ADuuu] [;] [Command] [;] [Parameter] [EXT] (02H) ( )() ( ASCII uuu=001 to 099 (Unit address) )() ( ) (03H) A message consists of [STX], [Address], [;], [Command], [;], [Parameter], and [ETX].
Item Format Note/Parameter Example Still OST : ccccc : m OST : 00005 : 1 CH #5 will be stilled. OST : ccccc : m Every segment in a multiscreen will be stilled. “cccc” expresses individual camera channel or all camera channels in a multiscreen. ccccc = 00001 to 00128 For individual ccccc = 00000 For all in a multiscreen “m” denotes display mode selection. m = 0: STILL OFF m = 1: STILL ON Multiscreen Pattern Select OTC : + OTC : + 4-segment, 9-segment or 16-segment toggles.
SPECIFICATIONS Power Source: Power Consumption: Camera Input (1-16)/(1-9)*: Playback Input: Camera Switching Input: Sampling Frequency: Quantizing: Pixels: Maximum Refreshing Rate: Camera Output (1-16)/(1-9)*: Recording Output: Multiscreen Output: Spot Output: Data (Input/Output): Alarm/Remote Control: Alarm Recover Input: Alarm Recover Output: Alarm Output: Ambient Operating Temperature: Ambient Operating Humidity: Dimensions: Weight: 220 V - 240 V AC 50 Hz 14 W 1.
Matsushita Electric Industrial Co., Ltd. Central P.O. Box 288, Osaka 530-91, Japan N0201-0 2001 © Matsushita Communication Industrial Co., Ltd. All rights reserved.
