221 LEG PRESS ADAPTER KIT FOR 220 GYM SYSTEM WARNING: Read and follow all directions for each step to insure proper assembly of this product. USER’S GUIDE CLASS H PART # 7031101 REV.
TABLE OF CONTENTS Safety Statement.............2 General Notes..................3 Tools Required................3 Gym Layout.....................4 Parts list..........................5 Assembly Instructions.....5-10 General Maintenance.......11 Warranty Statement..........12 Product Services..............13 Insert-Registration Card IMPORTANT SAFETY INFORMATION THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES! 1.
IMPORTANT NOTES Please note: * Thank you for purchasing the ParaBody 221 Leg Press Adapter Kit. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * This product must be assembled on a flat, level surface to assure its proper function. DO NOT securely tighten any frame connections until the entire frame has been assembled, unless otherwise stated.
1’ 2’ 3’ 5’ 4’ 6’ 7’ 8’ 1’ 2’ 3’ 4’ 5’ 6’ 7’ 8’ 1 Square = 1’ X 1’ Minimum Required Usable Space Length Width Height = 82 inches (208.5 cm) 6’ 10” = 71 inches (180.5 cm) 5’11” = 83 inches (211 cm) 6’ 11” Dimensions Including Leg Press (optional) Length Width = 82 inches (208.5 cm) 6’ 10” = 108 inches (180.
PARTS LIST KEY 1 2 3 4 5 PART # 70309 7014202 3116201 6467001 3108102 DESCRIPTION FRONT LEG LEG CABLE 3-1/2” PULLEY 2” COVER CAP QUICK DISCONNECT LINK QTY 1 1 1 2 1 KEY 6 7 8 9 10 PART # 3102501 3102802 3102924 3102904 3102906 DESCRIPTION 3/8” WASHER 3/8” LOCKNUT 3/8 X 1-3/4” BOLT 3/8 X 3” BOLT 3/8 X 4” BOLT QTY 7 4 1 2 2 NOTE: The LEG PRESS ATTACHMENT (100) must be assembled before connecting it to the PARABODY 220 GYM SYSTEM and can be attached to either side of the 220 GYM SYSTEM FIGURE 1 DISCA
10 3/8 X 4” 6 7 4 FIGURE 2 STEP 2: • Slide two 2” COVER CAPS (4) over the FRONT LEG (1) as shown in FIGURE 2 • SECURELY assemble the FRONT LEG (1) to the 220 Gym System using two 3/8 X 4” BOLTS (10), one previously removed 3/8” WASHER, three 3/8” WASHERS (6), one previously removed 3/8” LOCK NUT and one 3/8” LOCK NUT (7) as shown in FIGURE 2.
2 FIGURE 3 STEP 3: • Assemble the new LEG CABLE (2) using the previously removed bolts as shown in FIGURE 3. (NOTE: Make sure the LEG CABLE is running in the grooves of all pulleys and above the retaining bolts.
3 7 2 3/8 X 1-3/4” 8 1 FIGURE 4 STEP 4: • SECURELY assemble one 3-1/2” PULLEY (3) to the FRONT LEG (1) using one 3/8 X 1-3/4” BOLT (8) and one 3/8” LOCK NUT (7). See FIGURE 4.
1 3/8 X 3” 9 5 2 7 6 100 LEG PRESS FIGURE 5 STEP 5: • SECURELY attach the 100 LEG PRESS to the FRONT LEG (1) using two 3/8” X 3” BOLTS (9), four 3/8” WASHERS (6), and two 3/8” LOCK NUTS (7). See FIGURE 5. • Route LEG CABLE (2) around the 3-1/2” PULLEY on the LEG PRESS as shown in FIGURE 5. (NOTE: Pulley may need to be temporarily removed.) • Attach the end of the LEG CABLE (2) to the QUICK DISCONNECT LINK (5). See FIGURE 5.
SPRING PIN FIGURE 6 STEP 6: • The 100 LEG PRESS is equipped with a spring pin adjustment to accommodate different sized users and allow easy entry and exit from the machine. To use, you must slightly push against the foot plates to take tension off the pin. • Before setting the correct amount of tension in the cables, push the HEAD PLATE down, insert the WEIGHT SELECTOR PIN, and perform several repetitions at the leg press station.
MAINTENANCE Please note: * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714. * Inspect equipment daily. Tighten all loose connections are replace worn parts immediately. Failure to do so may result in serious injury * Lubricate guide rods with a teflon based (or equivalent) lubricant on a regular basis * PLEASE RECORD THE INFORMATION REQUESTED BELOW.
LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired or replaced by ParaBody. Terms: Lifetime – for so long as the Customer owns the ParaBody product. 2. LIMITED WARRANTY ON PARTS.
LIFE FITNESS 14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A. Tel: 763.323.4500 Fax: 763.323.4797 800.328.9714 (Toll-free within the U.S. and Canada) www.parabody.com INTERNATIONAL OFFICES Life Fitness Atlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 Life Fitness (UK) Ltd.
