l 441101 440 LEG PRESS ADAPTER KIT I WARNING: Read arid tbllow all directions for each step to insure proper assemblty of this product. I ASSEMBLY INSTRUCTIONS I Part # 7039101 REV.
]IMPORTANT NOTES[ There is a risk assumedby individuals whouse this type of equipment.To minimizerisk, please follow these rules: 1. Consult your physician before beginning any exercise program. 2. Inspect equipmentdaily. Tighten all loose connections and replace wornpa:rts immediately. Failure to do so mayresult in serious injury. 3. Donot allow minors or children to play on or around this equipment. 4. Exercise with care to avoid injury. 5.
PARTS LIST KEY PART # DESCRIPTION QTY KEY PART # DESCRIi?TION QTY 1 6686608 6693902 FRONT LEG 1 I 10 3102501 4 11 12 3102802 3102801 3/8" W~ ER 3/8" LO( NUT 13 3102924 3102904 3102918 2 3 4 5 6 7 8 9 6694002 6694208 3116201 6405201 6467001 3108102 6140701 PULLEY BRACKET CABLE SWIVEL BASE CONNECTION 1 1 PULLEY 2 14 2" SQ.
FIGURE 4 STEP 4 ¯ Securely fasten the FRONTLEG (1) and the BASECONNECTION (4) to the 440 HOMEGYMusing two 1/2 X 3-1/4" (15) and two 1/2" LOCKNUTS (12). See FIGURE FIGURE 5 STEP 5 ,,..., ¯ Remove one existing 3-1/2" PULLEYand two SPACERS from the ADJUSTMENT TUBE on the 100 LEG PRESS OPTIONby unfastening the 3/8 X 4-1/2" BOLTholding the pulley on. See FIGURE5. (Note: Save 3-1/2" PULLEY, it will be used in later steps.
STEP 6 ¯ Attach CABLE SWIVEL (3) to the ADJUSTMENT TUBE on the 100 LEG PRESSusing the existing previously removed 3/8 X 4-1/2" BOLTS, WASHERS, 2" WHEELS AND NUT. (Note: Securely tighten, then back off 1/4 turn to allow the CABLE SWIVEL & WHEELSto rotate freely.) See FIGURE6.
FIGURE 8 REMOVE STEP 8 Removethe existing ¯ Disconnect ¯ ¯ ¯ ¯ LATCABLE using the following steps: LAT BAR from TOP BOOM. Unscrew the threaded end of CABLEfrom the HEADPLATE ASSEMBLY. Route the LAT CABLEaround the PULLEYBLOCKas shown in FIGURE 8. Route the LAT CABLEaround the TOP BOOMas shown in FIGURE 8. The pulleys in TOP BOOM may need to be temporarily removed to remove CABLE.
FIGURE 9 ~TANT: Cable must run over the top of bolts. STEP 9 Install the NEW110-3/4" CABLE ASSY(16) using the following steps: ¯ Route the CABLE(16) through the TOP BOOM as shown in FIGURE9. The pulleys in TOPBOOM may need to be temporarily removed to perform this step. (Note: Make sure the CABLEis running OVERthe BOLTSconnecting the FRONTUPRIGHT to the TOPBOOM.These may also have to be removed to perform this step.
FIGURE 11 STEP 11 ¯ Attach the hook end of 82-1/2" CABLE(17) to the CABLESWIVEL(3) with one QUICKDISCONNECT LINK IMPORTANT:Tighten the QUICK DISCONNECTLINK (8) securely. ¯ Route the 82-1/2" 0 CABLE(17) under the WEIGHTSTACKas shown in FIGURE11.
STEP 12 FIGURE 12 ¯ Screw the threaded end of 82-1/2" CABLE(17) to the PULLEY BRACKET (2) as shown in FIGURE12. 3/8 X 1-3/4" FIGURE]13 STEP 13 ¯ Attach one 3-1/2" PULLEY(5) to the FRONTLEG (1) and one 3-1/2" PULLEY(5) to the BASECONNECI’ION (4) using 8 X 1-3/4" BOLTS(13) and two 3/8" LOCKNUTS (11). (Note: Make sure CABLE(17) is running utnder PULLEYS.
SPRING PIN ADJUSTMENT FIGURE 14 STEP 14 The 100 LEGPRESSxs equipped with a spring pin adjustment to accommodatedifferent sized users and allow easy entry and exit from the machine. To use, you must slightly push against the foot plates to take tension off the pin. To set the correct amountof tension in the cables, adjust the I00 LEGPRESSinto the last adjustment hole (so the LEGPRESSis spread apart) and remove the WEIGHTSTACKPIN.