INSTALLATION INSTRUCTION for ceiling fan
F6263 Installation & Operating Instructions for the Parrotuncle Owner’s Installation ,Manual Motor is core parts of the fan and the most expensive in all the components. The fan is used currently divided into two major categories of AC motor and DC motor, the AC motor is absolute mainstream. Although the AC motor occupies absolute advantage, but not the best solution. The main problem is common AC motor has big power consumption, high noise, large calorific value.
SAFETY PRECAUTION • WARNING –To make sure power is off before attempting installation. • WARNING – Support Directly From Building Structure. • WARNING –To reduce the risk of fire, electric shock, or injury to persons, unplug or disconnect the appliance from the power supply before the fan installation, cleaning, or servicing. • WARNING –Suitable for use with solid-state speed controls. • WARNING –Do not connect this fan to regulator or dimmer switch.
PARTS & ACCESSORIES Canopy Downrod Housing Blade Transmitter Kit Transmitter FAN OFF Transmitter Holder Battery Wall Screw x 2 LIGHT ON/OFF 1 4 5 2 2H F/R 4H AAA 1.5V AAA 1.
INSTALLATION INSTRUCTION STEP 1A - CONCRETE CEILING SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX. 1) Use the Mounting Bracket (1) as a guide, mark the spots where the 4 Expansion Bolts (2) will be drilled. 2) Remove the Mounting Bracket (1), drill 4 holes and insert 4 Expansion Bolts (2) into the concrete ceiling, install the mounting bracket and secure with Flat Washers (3), Spring Washers (4) and Nuts (5).
INSTALLATION INSTRUCTION Screw (1) Lock Pin (2) Hanger Ball (3) Canopy (4) Canopy Ring (5) Coupling cover (6) Downrod (7) Clevis pin (8) Nut (9) Spring Washer (11) Bolt (10) Cap (20) Coupling (14) Flat Washer (12) Screws (21) Set Screws (13) Allen Wrench (19) Fixing Screws (18) Blade (17) Hold Ring (16) Bulb (15) 4
INSTALLATION INSTRUCTION STEP 2 1) Remove the Clevis Pin (8), Nut (9), Spring Washers (11), Flat Washers(12) & Bolt (10) on Coupling (14). 2) Splice the three Blades (17) to the motor together without gaps. And align it with the hole of the motor. 3) Install the Hold Ring (16) from the bottom of the Blade, if the Hold Ring cannot be installed into the fan Blade smoothly, try to rotate the Hold Ring about 60º before installing it into the fan Blade.
INSTALLATION INSTRUCTION Safety Wire Clamp STEP 3 1) Raise the fan and place the hanger ball onto mounting bracket. 2) Rotate the fan until the notch on hanger ball snapped into the slot on mounting bracket and sits firmly. NOTE : THE DOWNROD AND HANGER BALL SHOULD NOT ROTATE IF THIS STEP IS DONECORRECTLY. 3) Tighten the safety wire clamp. 4) Place ring of safety wire through the Fan expansion bolt or self tapping screw and fix it to the building structure. 5) Connect the wire connector plugs correctly.
INSTALLATION INSTRUCTION STEP 4 MOTOR U MOTOR V MOTOR W FOR LIGHT N FOR LIGHT L G SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX. 1) Connect wires from controller to power supply with wire connectors. 2) Insert the controller into the space of the mounting bracket, and tidy up the wiring.
TRANSMITTER FUNCTION Load the battery into the transmitter, turn on the fan power supply and use it properly. FAN OFF LIGHT ON/OFF 1 4 5 2 3 2H 1H F/R 4H 8H AAA 1.5V AAA 1.5V ATTENTION 1) If the fan is not responding to the transmitter. Turn off the power supply to fan for 30 sec and hold down ”FAN OFF” the controller detects the signal and completes the setting, , The controller will issue “beep” sound two times, and the transmitter will be set successfully.
TRANSMITTER FUNCTION FAN OFF LIGHT ON/OFF 1 4 5 2 3 1H 2H F/R 4H 8H TRANSMITTER FUNCTION FAN SPEED Fan speed 1 – 5 control (1-low speed, 5-high speed) Turns off the fan FAN OFF Timing the fan 1H Auto off after 1 hr 2H Auto off after 2 hr 4H Auto off after 4 hr 8H Auto off after 8 hr Press the key or press the same time key to cancel the timer function.
TRANSMITTER FUNCTION Forward Reverse Fan rotates anti-clockwise creating a downward airflow delivering a cooling effect. Fan rotates clockwise creating an upward airflow moving warm air off the ceiling areas. This function works best at lower fan speed. Suitable for hot weather condition or air-conditioned condition. Suitable for cold weather or air-conditioned condition.
TECHNICAL SPECIFICATIONS 425mm ≥ 1000mm ≥ 2300mm 710mm Model F6263 No. of blades 3 Fan width 710mm Light Wattage Voltage 11W LED 110-120V~ 60Hz Speed Amps Wattage RPM CFM Nett weight Gross weight 1 2 3 4 5 0.060 0.081 0.161 0.212 0.285 2.9 7.5 11.1 18.5 23 100 130 160 195 220 1350 1800 2300 2600 2950 4.8 kg 5.9 kg Specifications & measurements shown are subject to ±5% variations.
MAINTENANCE Due to the fan’s natural movement, connections may get loose after a period of usage. To ensure a proper and safety usage, inspect the suspension system and tighten all connections every 6 months. Cleaning Cleaning your fan periodically will prolong its useful life. Basic cleaning procedures are as follows: 1. Please shut off the power before you clean the light fan and replace the bulbs. 2. The bulbs and nearby parts will be still hot after the power is shut off.
CAUTION THANK YOU FOR YOUR PURCHASE READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION. IF UNSURE CONSULT A QUALIFIED ELECTRICIAN Thank you for purchasing this quality product. To ensure correct function and safety, please read and save all instructions before using the product LIGHT FAN THE BEST PARTNER OF AIR CONDITIONER & AIR PURIFIER A lot of people think the fan is only used in the summer, actually fan has a great purpose is to speed up the indoor air circulation.