Datasheet

ManualsBrandsPatlite ManualsAutomationPatlite Signal tower component LR7-E-Y Yellow Yellow Flasher, Non-stop light signal

Mount A

WJ/PJ/WT Mounting Diagram

Mount B

LJ Mounting Diagram

Mount C

QJ Mounting Diagram

A minus driver, etc., is used

to pry the Terminal Block

open by pushing straight

onto the lever slot.

Recommended Torque

0.6 N/m

Recommended Torque

1.4 N/m

Wiring Diagrams

Mounting Dimensions (Unit: mm)

120°

Nameplate

Wiring Hole (φ12)

120°

Nameplate

Bracket

Shape

Wire Hole

φ15

φ73

φ54 - φ56

Mounting

Hole φ6x4

Mounting

φ6x4

Nut/Screw

M5x4

90°

From Pole

center

36.9

18.5

█ Wiring Method

[WT] Terminal Type

█ Terminal Block

External Contact Type

Contact Relay Type

External Contact Type

PLC (NPN Transistor Type)

Product Type

Model

External Contact Type

PLC (PNP Transistor Type)

Schematic

Output Unit 2

Output Unit 1

PLC

External

Contact

Flashing/

Buzzer

External

Contact

Non-flashing/

Buzzer

LR4, LR6

LED Red

LED Amber

LED Green

LED Blue

LED White

Power Source Line

Common Line

Flashing Common Line

Buzzer

Power Source Line

Only apply voltage to Power Supply Lines.

External Contact Type

Contact Relay Type

Product Type

Model

Fuse

AC 100 - 240 V

※ Used when buzzer unit is attached.

Flashing/

Buzzer

Non-flashing/

Buzzer

LR4, LR6

LED Red

LED Amber

LED Green

LED Blue

LED White

Power Source Line

Common Line

Flashing Common Line

Buzzer

Power Source Line

Only apply voltage to Power Supply Lines.

External Contact Type

PLC (NPN Transistor Type)

Fuse

AC 100 - 240 V

※ Used when buzzer unit is attached.

[01] DC 12V [02] DC 24V [M2] AC 100 - 240V

█

Recommended Wire Gauges

UL1007 / UL1430

Wire Type

0.14 - 1.5mm

Wire (Solid)

AWG30 - 14

Wire (Frayed)

Lever

The stripped lead wire

is inserted into the slot.

Removing the driver

releases the lever.

Mounting Holes x3

φ4

φ5

LR4/5-WJ

LR5-WT

LR4/5/6-PJ

LR6/7-WJ

LR7-WT

Nut/

Screw

φ30

φ40

LR4/5-WJ

LR5-WT

LR4/5/6-PJ

LR6/7-WJ

LR7-WT

17 18

Specification

• Temperature rating should be above 75

C, and the

conductor material should be of copper wire.

Orange

Brown

Red

Green

Blue

White

Purple

Gray

Yellow

Black

Orange

Brown

Red

Green

Blue

White

Purple

Gray

Yellow

Black

LR - 02 / LR5- 01 W

LR - M2 W

DC 12 V (LR5 included) (Class 2) (Non-polar)

DC 24 V (Class 2) (Non-polar)

Schematic

Output Unit 2

Output Unit 1

Do not Apply Voltage!

Fuse

PLC

LR4 - LR7

LED Red

LED Amber

LED Green

LED Blue

LED White

Power Source Line

Flashing Common Line

Buzzer

Power Source Line

Flashing/

Buzzer

Non-flashing/

Buzzer

※ Used when buzzer unit is attached.

LR4-LR7

DC 12 V (LR5 included) (Class 2) (Non-polar)

DC 24 V (Class 2) (Non-polar)

LED Red

LED Amber

LED Green

LED Blue

LED White

Power Source Line

Flashing Common Line

Buzzer

Power Source Line

External

Contact

Flashing/

Buzzer

External

Contact

Non-flashing/

Buzzer

Do not Apply Voltage!

※ Used when buzzer unit is attached.

Fuse

Do not Apply Voltage!

Fuse

PLC

Schematic

Output Unit 2

Output Unit 1

LR4 - LR7

LED Red

LED Amber

LED Green

LED Blue

LED White

Power Source Line

Flashing Common Line

Buzzer

Power Source Line

Flashing/

Buzzer

Non-flashing/

Buzzer

※ Used when buzzer unit is attached.

DC 12 V (LR5 included) (Class 2) (Non-polar)

DC 24 V (Class 2) (Non-polar)

LED Yellow

LED Red

LED Green

LED Blue

LED White

Buzzer

Power (Common)

Flashing Common

Power (Signal)

Black

Grey

Blue

Grey

Green

Orange

Red

Yellow

White

Make holes for the mounting and wire-distribution. Refer to the

suitable attachment or mounting dimension figure for the model.

Run wiring

through the

mounting hole.

Secure the product with the bolts, nuts and

screws. Required nuts and bolts for (LJ) are not

included.

When not using an

L-bracket, make a

fitting hole of

22-23mm.

12.2 N/m

Recommended Bolt Torque

30 N

Recommended Torque

Point

Feed the wiring

through the hole

and set the pole

in place to install.

Mounting

Surface

L-bracket

Mounting

Hole

(φ9)

Mounting

Surface

Mounting

Hole

(φ11)

For M8 bolt and nut size

For M10 bolt and nut size

Orange

Brown

Red

Green

Blue

White

Purple

Gray

Yellow

Orange

Brown

Red

Green

Blue

White

Purple

Gray

Yellow

Orange

Brown

Red

Green

Blue

White

Purple

Gray

Yellow

Specifications

-20

℃

- +50

℃

90% RH or less, no condensation

-30

℃

- +60

℃

90% RH or less, no condensation

Indoor Use

Upright Position

IP65 (IEC 60529) / NEMA TYPE 4X, 13

Upright Position

More than 1M

at DC500V between the power input lead and chassis

AC500V for 1 minute between terminals and chassis without breaking insulation (M2: AC1500V for 1 min.)

60 ±2 flashes/ min

ab. -10dB reduction

Buzzer Sound No.4 (Sweep) from all directions at a 1m distance

NPN / PNP (AC100 - 240V is NPN only)

Operating Ambient Temperature

Operating Humidity Range

Storage Temperature Range

Storage Humidity Range

Mounting Location

Mounting Direction

Protection Rating

Environmental Conditions

Insulation Resistance

Withstand Voltage

Flash Rate

Sound Level

Sound Reduction

Environmental Conditions

Buzzer Sound

Transistor Output

Conformity Standards

●UL 508, CSA-C22.2 No.14 ●EMC Directive (EN 61000-6-4, EN 61000-6-2)

●FCC Part 15 Subpart B Class A ●KC (KN 61000-6-4, KN 61000-6-2)

●RoHS Directive (EN 50581) ●Low-voltage Directive (IEC/EN 60947-5-1, EN62471)

LED Unit Specifications Buzzer Unit Specifications

Conformity Standards

Current

Consumption/

Power

Consumption

Rated Voltage

Color Red Amber Green Blue White

Typ.

Max.

Rated Voltage

Current

Consumption/

Power

Consumption

Typ.

Max.

0.3A/1.3W

0.04A/1W

DC24V

●UL 508, CSA-C22.2 No.14

●EMC Directive (EN 61000-6-4, EN 61000-6-2)

●RoHS Directive (EN 50581)

●UL 508, CSA-C22.2 No.14

●EMC Directive (EN 61000-6-4, EN 61000-6-2)

●FCC Part 15 Subpart B Class A

●RoHS Directive (EN 50581)

0.045A/

1.3W

0.04A/

0.045A/

1.3W

0.04A/

0.045A/

1.3W

0.04A/

0.045A/

1.3W

0.04A/

0.045A/

1.3W

0.04A/

DC24V

AC100 - 240V

40mA

≧

100mA Vs

≧

DC35V

40mA

≧

300mA Vs

≧

DC35V

150mA

Current rating higher than inrush current

None

25A (Ta=25℃) , 50A (Ta=50℃) at 2.0ms

or less

LED Unit

(Per Tier)

Buzzer

Power

Inrush Current

Signal Line Current

Contact Capacity

Signal Line Current

Contact Capacity

Current Consumption

Contact Capacity

Signal Line

Power Line

Rated Voltage

DC12V

90mA

≧

100mA Vs

≧

DC35V

90mA

≧

300mA Vs

≧

DC35V

500mA

≧

700mA Vs

≧

DC35V

None

0.7A at 15ms or less

DC24V

40mA

≧

100mA Vs

≧

DC35V

40mA

≧

300mA Vs

≧

DC35V

250mA

≧

700mA Vs

≧

DC35V

None

0.7A at 0.5ms or less

≦

0.1 mA

Leakage Contact Current

External Contact Capacity

Is:Current Capacity Vs:Saturated Voltage I

:Leakage Current Ta:Ambient Temperature

*1: LR5 Only *2: LR4/LR6 Only *3: An inrush current of 0.7A flows through the signal line when the Gray power source line is disconnected. Be sure to select an external contact which can withstand the capacity.

[Recommended Fuse] Rated Current: 250V / 1A 5x20mm Fast-blow Glass Fuse

*1: LJ Type is IP54 *2: Dependent on DIP Switch Settings *3: M2 Type Only

Typ. 85dB

LR4

Typ. 85dB

LR5

Typ. 88dB

LR6

Typ. 90dB

LR7

Typ. 80dB

LR5 DC12V

4 patterns

Rapid Intermittent sound

No.1

Continuous sound

No.2

Rapid Hi-low

No.3

Sweep sound

No.4