52” CROWN POINT CEILING FAN Owner’s Manual Model #20675 SKU #355-0641 If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: 1-877-459-3267, 8 a.m. - 5 p.m. Central Time, Monday - Friday.
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1 2 PACKAGE CONTENTS 4 3 11 13 15 20 7 10 21 12 18 16 14 16 22 Hardware Kit 17 23 Owner’s Manual 14. Switch Housing Cap 5. Downrod 17. Light Cage Screw (x12) 6. Downrod Pin 18. Light Cage (x3) 7. Downrod Clip 19. E26-base LED Bulb (x3) 8. Yoke Cover 20. Blade (x5) 9. Set Screw (x2) 21. Blade Arm (x5) 10. Closemount Screw (x3) 22. Hardware Kit 11. Motor Assembly 23.
DIMENSION REFERENCE D C B A A. 17.87 in. B. 12.41 in. C. 10.92 in. D. 5.13 in. MOUNTING OPTIONS Three Mounting Options Closemount Downrod Mount Angled Ceiling Mount (Up to 16 degrees) Choose one of the following mounting options: Closemount is best suited for ceilings lower than 8 feet. It does not utilize the downrod. Downrod Mount is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer downrod (not included).
SAFETY INSTRUCTIONS READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SAVE INSTRUCTIONS. CAUTION: All set screws of the fan must be checked and retightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or cleaning fan. Do not insert foreign objects in between rotating fan blades.
ASSEMBLY INSTRUCTIONS 1. Turn OFF the electrical power at the main fuse or circuit breaker. DANGER: Failure to disconnect the power supply prior to installation may result in serious injury or death. 1 Mounting Bracket Screw 2 2. Loosen all four mounting bracket screws located on the mounting bracket and completely remove the two screws from the round holes in the canopy. Save the screws for later. Remove the canopy from the mounting bracket.
ASSEMBLY INSTRUCTIONS Downrod 5. DOWNROD MOUNT - Remove the downrod clip and downrod pin from the downrod. Then, loosen but don’t remove the two set screws at the top of the yoke. Downrod Clip Downrod Pin Set Screw 5 Yoke 6. Insert the downrod through the canopy and yoke cover. Feed the wires from the fan through the downrod. Canopy Yoke Cover Downrod 6 Set Screw Downrod Downrod Pin Yoke Downrod Clip Downrod Slot 7 Tab 8 Mounting Bracket 7.
ASSEMBLY INSTRUCTIONS 10. Use wire connectors to connect the fan wires to the power supply wires according to the wiring diagram and the following instructions: Black (hot) White (neutral) Green White Black Blue Bare/Green (ground) 10 Wire Connector WARNING: Do NOT wire the fan motor to a variablespeed (dimmer) wall control. Note: If there is a second hot/power wire coming from the outlet box, connect it to the blue (light power) fan wire for separate light and fan control.
ASSEMBLY INSTRUCTIONS Cage Screw 14. Remove the four cage screws from the brackets inside the shade. Install the E26-base LED bulb into the socket of the light kit. Then attach the light cage to the shade using the four cage screws. Repeat for each shade. Light Cage Bulb Bracket 14 Important: Make sure you allow the bulb and light kit to cool before you replace the bulb. Shade Switch Housing Single-Pin Connector Reverse Switch Notch 15 Switch Housing Screw Light Kit 15.
ASSEMBLY INSTRUCTIONS 18. INSTALLATION WITHOUT THE LIGHT KIT (continued) Reverse Switch Notch Switch Housing Cap Switch Housing Screw 18 c. Remove the three switch housing screws from the top edge of the switch housing cap. e. Use the switch housing screws to attach to the switch housing. Note: Align the notch in the switch housing cap with the reverse switch. Attach the pull chain extension to the pull chain (see Step 16). 19.
OPERATING INSTRUCTIONS Reverse Switch 1 1. Using a ceiling fan will allow you to raise your thermostat setting in summer and lower your thermostat setting in winter without feeling a difference in your comfort. In warmer weather, push the reverse switch down which will result in downward airflow creating a wind chill effect. In cooler weather, push the reverse switch up which will result in upward airflow that can help move stagnant, hot air off the ceiling area.
TROUBLESHOOTING If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check the Troubleshooting section below. If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: 1-877-459-3267, 8 a.m. - 5 p.m. Central Time, Monday - Friday.
LIMITED LIFETIME WARRANTY To obtain Service, please contact the Service Department: 1-877-459-3267, 8 a.m. - 5 p.m. Central Time, Monday - Friday.
