52” TISBURY II CEILING FAN Owner’s Manual Models #20687 (355-0678) 20688 (355-0679) If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time.
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1 2 3 PACKAGE CONTENTS 12. Motor Screws (x10) 1. Canopy 4 2. Canopy Cover 3. Mounting Bracket Screw 14. Fitter Plate Screws (x3) (x4) 15. Light Kit 4. Mounting Bracket 16. Socket Ring (x3) 5 7 6 22 8 5. Downrod 17. Glass Shade (x3) 6. Downrod Pin 21 10 9 18. Owner’s Manual 7. Downrod Clip 19. Hardware Kit 8. Yoke Cover 11 9.
DIMENSION REFERENCE D C B A A. 19.35 in. B. 11.99 in. C. 11.26 in. D. 5.13 in. MOUNTING OPTIONS Three Mounting Options Closemount Downrod Mount Angled Ceiling Mount (Up to 16 degrees) Choose one of the following mounting options: Closemount method is best suited for ceilings lower than 8 feet. It does not utilize the downrod. Downrod Mount is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer downrod (not included).
SAFETY INSTRUCTIONS READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SAVE INSTRUCTIONS. CAUTION: All set screws of the fan must be checked and retightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or cleaning fan. Do not insert foreign objects in between rotating fan blades.
ASSEMBLY INSTRUCTIONS 1. Turn OFF the electrical power at the main fuse or circuit breaker. 1 Mounting Bracket Screw 2 3 2. Remove the mounting bracket by removing the two mounting bracket screws from the round holes in the canopy. Then loosen the other two mounting bracket screws from the J-shaped slots. Retain the mounting bracket screws for later. 3. Install the mounting bracket to the outlet box (not included) using the screws and washers provided with the outlet box.
ASSEMBLY INSTRUCTIONS Closemount Screw Mounting Bracket 5 Canopy 5. CLOSEMOUNT INSTALLATION (Optional) a. Remove the three Phillips-head closemount screws from the top of the motor assembly. b. Remove the canopy cover from the bottom of the canopy. c. Align the holes in the bottom of the canopy with the screw holes in the top of the motor assembly. The larger holes in the canopy will encompass the three pre-installed screws. d.
ASSEMBLY INSTRUCTIONS 9. Lift the downrod into the mounting bracket. Rotate the downrod until the tab in the mounting bracket is seated in the slot in the downrod ball. Slot Tab Downrod 9 Black (hot) White (neutral) Green White Black Blue Bare/Green (ground) J-shaped Slot 10 WARNING: Do NOT wire the fan motor to a variable-speed (dimmer) wall control. Important: After the connections have been made, the connected wires should be turned upward and pushed carefully up into the outlet box.
ASSEMBLY INSTRUCTIONS 13. Install the blade arm to the underside of the motor assembly with previously removed motor screws. Tighten each blade arm completely before moving to the next. 13 Blade Arm Note: The notch in the fitter plate allows a Phillips screwdriver access to the motor screws. Motor Screw 14. . Connect the single-pin connectors from the fitter plate to the single-pin connectors from the light kit -blue to black and white to white. Single Pin Connector 14 15.
ASSEMBLY INSTRUCTIONS 17. Install the E26-base LED bulbs into the sockets of the light kit. 17 E26 LED Bulb 18. Attach the pull chain extensions to the pull chains. 18 Pull Chain Extension 19. Restore the power at the main fuse or circuit breaker.
OPERATING INSTRUCTIONS 1. The fan pull chain has four positions to control fan speed. One pull is HIGH, two is MEDIUM, three is LOW and four turns the fan OFF. The light pull chain turns the light ON and OFF. 1 Fan Pull Chain Light Pull Chain 2. Use the reverse switch to optimize your fan for seasonal performance. Using a ceiling fan will allow you to raise your thermostat setting in summer and lower your thermostat setting in winter without feeling a difference in your comfort.
TROUBLESHOOTING If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check the Troubleshooting section below. If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time. PROBLEM SUGGESTED REMEDY 1. Fan does not start 1.
LIMITED LIFETIME WARRANTY To obtain Service, please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. central time.
