Installation Instructions

ManualsBrandsPatriot Lighting ManualsChandeliersPhinny Matte Black 5-Light Chandelier

medium base bulbs required:

5 x 60 watt max. A19 incandescent bulbs

or 13 watt max. SBCFL/SBLED bulbs

(bulbs sold separately)

Questions, problems, missing parts?

Before returning to your retailer, call our customer service at 1-800-527-1292

Monday – Friday 8:30 a.m. – 5:00 p.m. CST

PRINTED IN CHINA

PACKAGE CONTENTS

HARDWARE CONTENTS Note: Hardware not shown actual size.

IMPORTANT REMINDER: You must

use the parts provided with this fixture for

proper installation and safety.

Sku Number: 351-8413

5-LIGHT CHANDELIER

Model Number: CHM7MBK

Wire Connector

Screw Collar Loop

(pre-attached)

Mounting Screw

Mounting strap

Connecting chain link

(pre-attached)

Threaded ring

(pre-attached)

Summary of content (7 pages)

PAGE 1
Sku Number: 351-8413 5-LIGHT CHANDELIER Model Number: CHM7MBK Questions, problems, missing parts? Before returning to your retailer, call our customer service at 1-800-527-1292 Monday – Friday 8:30 a.m. – 5:00 p.m. CST PACKAGE CONTENTS A D C B F E HARDWARE CONTENTS Note: Hardware not shown actual size. EE AA Mounting strap x1 BB Screw Collar Loop (pre-attached) CC x1 IMPORTANT REMINDER: You must use the parts provided with this fixture for proper installation and safety.
PAGE 2
SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. Please read and understand this entire manual before attempting to assemble, operate or install the product. WARNING • To reduce the risk of electrical shock, turn off the electricity at the main fuse box or circuit panel before you begin the installation or before servicing or installing the fixture.
PAGE 3
ASSEMBLY INSTRUCTIONS 1. Turn off circuit breakers and wall switch to the fixture supply line leads. WARNING: Failure to disconnect power supply prior to installation may result in serious injury. ON ON OFF OFF 2. Remove existing fixture. WARNING: When using an existing outlet box, be sure the outlet box is securely attached to the building structure and can support the full weight of the fixture. Failure to do so can result in serious injury. 3.
PAGE 4
ASSEMBLY INSTRUCTIONS (continued) 5. Attach and close connecting chain link (DD) to fixture loop (C). Feed wiring through chain (D) to desired length. D screwdriver extra chain pliers If you will be using the chain as is skip to the following step. If you wish to SHORTEN the chain remove connecting chain link (DD) from other end of chain (D). Open the chain link at desired length using pliers, a flat-head screwdriver and a soft cloth to prevent scratching the chain.
PAGE 5
ASSEMBLY INSTRUCTIONS (continued) 8. Prepare wire by stripping 1/2 inch of insulation from wire ends using wire strippers (not included). GREENscrew Feed wiring and bare GROUND wire through hole at bottom of threaded rod. Gently push wiring and bare GROUND wire until they come through top of threaded rod. Pull all wiring until there is no extra slack left in the wires running through the chain.
PAGE 6
ASSEMBLY INSTRUCTIONS (continued) 10. Gently push wiring into outlet box and then slowly slide canopy (A) and threaded ring (CC) up chain. Secure canopy (A) to mounting strap by tightening threaded ring (CC). AA BB A CC 11. Remove socket covers (E) from sockets. Place shade (F) over socket and secure by replacing socket cover (E). Install 5 medium base bulbs --either 60 watt max. A19 incandescent bulbs or 13 watt max. SBCFL/SBLED bulbs (bulbs sold separately).
PAGE 7
CARE AND MAINTENANCE • To clean, turn off power and wipe fixture with a damp, non-abrasive cloth. TROUBLESHOOTING WARNING: Failure to disconnect power supply prior to troubleshooting any wiring issues may result in serious injury. Problem: Light(s) does/do not come on. Solutions: 1. Check power (circuit box and wall switch) to fixture. 2. Verify that bulbs are installed correctly. 3. Check to be sure wires are connected properly with wire connectors. 4. Replace defective bulbs with same type of bulb.