Model No.
Package Contents: 1 2 6 3 7 4 5 10 9 8 X16 11 9V 12 13 14 15 16 Unpack your fan and check the contents. You should have the following items. 1.) Hanger Bracket 2.) Canopy 3.) Canopy Cover (Comes in a separate bag) 4.) Downrod Set (Included Hanger Ball, 6” Downrod, Hanger Pin & Lock Pin) 5.) Downrod Stand Cover 6.) Fan Blade (5 PCS) 7.) Fan Motor Assembly 8.) Blade bracket (5 PCS) 9.) Fan Light 10.) Glass Shade (3 PCS) 11.) Assembly Kit 12.) Installation Instructions 13.
Exploded View Detail Hanger Bracket Hanger Ball Canopy Downrod Canopy Cover Lock Pin Hanger Pin Downrod Stand Cover Collar Housing Blade Bracket Switch Box Blade Fan Light Glass Shade LED Bulb Triple Mount Options Ceiling Mount Downrod Mount Slope Ceiling Mount ( Up to 23 degrees) PAGE: 3 / 11 191022
Safety Instructions READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN TO INSTALL THE FAN AND SAVE INSTRUCTIONS. All set screws of the fan must be checked and retightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or cleaning the fan. Do not insert foreign objects between rotating fan blades.
INSTALLATION INSTRUCTIONS IMPORTANT: BEFORE YOU BEGIN INSTALLATION, CAREFULLY READ ALL INFORMATION PROVIDED IN THE SAFETY INSTRUCTIONS AND INSTALLATION INSTRUCTIONS. IF IN DOUBT, CONSULT A QUALIFIED ELECTRICIAN. SAVE ALL INSTRUCTIONS. NOTE: The fan weight is 18.96 lbs (8.6 kgs). Be sure the outlet box you are using is securely attached to the building structure and can support the full weight of the fan. Failing to do so can result in serious injury.
Antenna Receiver There is a code switch in the transmitter and receiver. This "DIP Switch" is a 4 key unit (Fig.9). All keys were set at "ON" position in the beginning. Set the keys to a different code. Make sure the same numbered keys are switched "ON" for both DIP Switches (Fig.9a). Take note that the "ON" position may have different orientation in each. DIP Switch Fig.9a Fig.9 Code example: 1-ON 2-OFF 3-ON 4-OFF on both DIP Switches. Transmitter Fig.
Fig.12 Fig.14 Hanger Bracket Screw Blade Screw Washer Blade Canopy Plastic Insert Washer Washer Attach the canopy to the hanger bracket, and then secure it with four screws and washers. Blade Bracket Fig.13 Tighten blades to blade brackets by using blade screws and washer. Blade Bracket Motor Screw Remove the motor screws and washers from the fan motor assembly. Secure blade brackets to the motor with washers and motor screws.
Reverse Slide Switch Fig.21 Fig.20 Turn on the electric power at the main fuse or circuit breaker box. Forward The slide switch on switch box sets direction of fan rotation. Select the desired direction of fan rotation. Push the slide switch down for " Forward" and up for "Reverse". Note: Wait for fan to stop before reversing the direction of blade rotation. Fig.22 Note: 1. This remote controller has memory function setting.
For a single switch Follow these steps: ck Bla e Whit White G ro Blue Connect the black (hot) wire (This is for fan control) and blue wire (This is for light control) from motor to the black (hot) wire from outlet box with a wire connector. en Gre Connect the white (neutral) wire from motor to the white (neutral) wire from the outlet box with a wire connector. un Connect three ground wires (Green or bare copper) coming from outlet box, downrod and hanging bracket with a wire connector.
Troubleshooting Guide If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation or wiring. If you experience any faults, please check this Troubleshooting Guide. If a problem cannot be remedied or you are experiencing difficulty in installation, please call our Customer Service Department (1-800-887-6326). PROBLEM SUGGESTED REMEDY 1. If fan does not start: 1. Check main and branch circuit fuses or circuit breakers. 2.
DYNAMIC BLADE BALANCING KIT YARDSTICK 1 BALANCING WEIGHT CENTERLINE 2 3 4 5 6 7 8 MEASURING POINT 9 PLASTIC CLIP COUNTERCLOCKWISE PREFACE Your ceiling fan may sometimes have wobbling problems when operating due to irregularity in the blades or the blade brackets. Improper assembly in the mounting system may cause some additional problems. This balancing kit can be used to fix wobbling problems. DYNAMIC BLADE BALANCING KIT FOR CEILING FANS 1.